AN EXPERIMENTAL INVESTIGATION OF THE EARTH-RESISTANCE RESPONSE OF A REINFORCED CONCRETE PILE.

1981 ◽  
Vol 71 (4) ◽  
pp. 1101-1129 ◽  
Author(s):  
WJ MCCARTER ◽  
HW WHITTINGTON ◽  
MC FORDE
Keyword(s):  
Experimental Investigation ◽  
Reinforced Concrete ◽  
Resistance Response ◽  
The Earth ◽  
Concrete Pile

scholarly journals Effect of the Geometrical Constraints to the Wenner Four-Point Electrical Resistivity Test of Reinforced Concrete Slabs

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4622
Author(s):  
Kevin Paolo V. Robles ◽  
Jurng-Jae Yee ◽  
Seong-Hoon Kee
Keyword(s):  
Experimental Investigation ◽  
Electrical Resistivity ◽  
Reinforced Concrete ◽  
Concrete Slab ◽  
Plain Concrete ◽  
Electrode Spacing ◽  
Concrete Slabs ◽  
Reinforced Concrete Slabs ◽  
Spacing Ratio ◽  
Geometrical Constraints

The main objectives of this study are to evaluate the effect of geometrical constraints of plain concrete and reinforced concrete slabs on the Wenner four-point concrete electrical resistivity (ER) test through numerical and experimental investigation and to propose measurement recommendations for laboratory and field specimens. First, a series of numerical simulations was performed using a 3D finite element model to investigate the effects of geometrical constraints (the dimension of concrete slabs, the electrode spacing and configuration, and the distance of the electrode to the edges of concrete slabs) on ER measurements of concrete. Next, a reinforced concrete slab specimen (1500 mm (width) by 1500 mm (length) by 300 mm (thickness)) was used for experimental investigation and validation of the numerical simulation results. Based on the analytical and experimental results, it is concluded that measured ER values of regularly shaped concrete elements are strongly dependent on the distance-to-spacing ratio of ER probes (i.e., distance of the electrode in ER probes to the edges and/or the bottom of the concrete slabs normalized by the electrode spacing). For the plain concrete, it is inferred that the thickness of the concrete member should be at least three times the electrode spacing. In addition, the distance should be more than twice the electrode spacing to make the edge effect almost negligible. It is observed that the findings from the plain concrete are also valid for the reinforced concrete. However, for the reinforced concrete, the ER values are also affected by the presence of reinforcing steel and saturation of concrete, which could cause disruptions in ER measurements

Experimental Study on Earth Pressure of Corrugated Steel Culvert under High Fill Embankment

2013 ◽  
Vol 405-408 ◽  
pp. 1815-1819
Author(s):  
Wen Sheng Yu ◽  
Zhu Long Li ◽  
Xiao Ru Xie ◽  
Li Yuan Guo
Keyword(s):  
Mechanical Property ◽  
Experimental Study ◽  
Reinforced Concrete ◽  
Concrete Slab ◽  
Earth Pressure ◽  
Reinforced Concrete Slab ◽  
The Earth ◽  
Filling Height ◽  
Test Points ◽  
Better Than

To analyze the earth pressure of corrugated steel culvert under high fill embankment, a field test was taken and the change law was got with the filling height increasing, the force state when geotechnical grilles were laid on the top of corrugated steel culvert was compared to that of reinforced concrete slab culvert. Results show that the pressure on the top of corrugated steel culvert is smaller than that on the external in same level when test points are near to culvert, the values of test points above and below geotechnical grilles are close, and the pressure of corrugated steel culvert is smaller than that of reinforced concrete slab culvert when filling height is above 7.3 m. So analysis indicates corrugated steel culvert spreads the upper load better, the geotechnical grille can reduce the pressure effectively through earth pressure redistribution, and the mechanical property of corrugated steel culvert is better than reinforced concrete slab culvert under high fill embankment.

Sign in / Sign up

Export Citation Format

Share Document