HEAT TRANSFER CHARACTERISTICS DURING THE CRITICAL HEAT FLUX CONDITION IN A SUBCOOLED FLOW BOILING SYSTEM

1986 ◽  
Author(s):  
Tatsuhiro Ueda ◽  
Kyung-kun Kim
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
Heat Transfer Characteristics ◽  
Subcooled Flow Boiling ◽  
Transfer Characteristics ◽  
Flux Condition ◽  
Subcooled Flow

scholarly journals Alumina Nanoparticle Pre-Coated Tubing Enhancing Subcooled Flow Boiling Critical Heat Flux

2009 ◽  
Author(s):  
Bao Truong ◽  
Lin-wen Hu ◽  
Jacopo Buongiorno ◽  
Thomas McKrell
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Subcooled Flow Boiling ◽  
Nanoparticle Deposition ◽  
Subcooled Flow ◽  
Flow Boiling Heat Transfer

Nanofluids are engineered colloidal dispersions of nano-sized particle in common base fluids. Previous pool boiling studies have shown that nanofluids can improve critical heat flux (CHF) up to 200% for pool boiling and up to 50% for subcooled flow boiling due to the boiling induced nanoparticle deposition on the heated surface. Motivated by the significant CHF enhancement of nanoparticle deposited surface, this study investigated experimentally the subcooled flow boiling heat transfer of pre-coated test sections in water. Using a separate coating loop, stainless steel test sections were treated via flow boiling of alumina nanofluids at constant heat flux and mass flow rate. The pre-coated test sections were then used in another loop to measure subcooled flow boiling heat transfer coefficient and CHF with water. The CHF values for the pre-coated tubing were found on average to be 28% higher than bare tubing at high mass flux G = 2500 kg/m2 s. However, no enhancement was found at lower mass flux G = 1500 kg/m2 s. The heat transfer coefficients did not differ much between experiments when the bare or coated tubes were used. SEM images of the test sections confirm the presence of a nanoparticle coating layer. The nanoparticle deposition is sporadic and no relationship between the coating pattern and the amount of CHF enhancement is observed.

Flow Pattern Analysis and Heat Transfer Characteristics During Subcooled Flow Boiling in a Rectangular Microchannel on ZnO Microrod Surface

2021 ◽  
Vol 143 (12) ◽  
Author(s):  
Yuhao Lin ◽  
Junye Li ◽  
Jia Sun ◽  
Wei Li ◽  
Yanlong Cao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Pattern ◽  
Titanium Surface ◽  
Flow Boiling ◽  
Bubbly Flow ◽  
Heat Transfer Characteristics ◽  
Rectangular Microchannel ◽  
Subcooled Flow Boiling ◽  
Subcooled Flow

Abstract The combination of microstructured surface and microchannel flow boiling is expected to solve the thermal management problems of high-heat-flux devices. In this study, the experimental investigation of subcooled flow boiling in a high aspect ratio, one-sided heating rectangular microchannel was conducted with de-ionized water as the working fluid. ZnO microrods were synthesized on the titanium surface to be used as the heated surface compared with the bare titanium surface. A facile image tool is utilized to process the flow patterns photographed by a high-speed camera, which is analyzed with the heat transfer characteristics. The flow pattern of isolated bubbly flow reveals the large number of nucleation sites formed on the microrod surface but the heat transfer performance deteriorates with increasing mass flux because of the smaller bubble area and weaker nucleation. With increasing heat flux, the flow pattern changes from isolated bubbly flow to alternating bubbly/slug flow and alternating slug/annular flow. The latter flow pattern is confirmed to bring a higher heat transfer coefficient due to the larger area of thin-film evaporation. Compared with the bare surface, a higher heat transfer coefficient is achieved on the ZnO microrod surface for up to 37% due to the more nucleate sites and strengthened convective evaporation. Therefore, this surface might be suitable for heat dissipation in the watercraft or aerospace industry considering the low density, strong intensity, and corrosion resistance of titanium.

Sign in / Sign up

Export Citation Format

Share Document