AN EXPERIMENTAL INVESTIGATION INTO FILM COOLING WITH PARTICULAR APPLICATION TO COOLED TURBINE BLADES

1970 ◽  
Author(s):  
D.W. Artt ◽  
A. Brown ◽  
P.P. Miller
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Turbine Blades

scholarly journals Comparison of Two-Equation Turbulence Models for Prediction of Heat Transfer on Film-Cooled Turbine Blades

1997 ◽  
Author(s):  
Vijay K. Garg ◽  
Ali A. Ameri
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Computer Time ◽  
Suction Surface ◽  
The Heat Transfer Coefficient

A three-dimensional Navier-Stokes code has been used to compute the heat transfer coefficient on two film-cooled turbine blades, namely the VKI rotor with six rows of cooling holes including three rows on the shower head, and the C3X vane with nine rows of holes including five rows on the shower head. Predictions of heat transfer coefficient at the blade surface using three two-equation turbulence models, specifically, Coakley’s q-ω model, Chien’s k-ε model and Wilcox’s k-ω model with Menter’s modifications, have been compared with the experimental data of Camci and Arts (1990) for the VKI rotor, and of Hylton et al. (1988) for the C3X vane along with predictions using the Baldwin-Lomax (B-L) model taken from Garg and Gaugler (1995). It is found that for the cases considered here the two-equation models predict the blade heat transfer somewhat better than the B-L model except immediately downstream of the film-cooling holes on the suction surface of the VKI rotor, and over most of the suction surface of the C3X vane. However, all two-equation models require 40% more computer core than the B-L model for solution, and while the q-ω and k-ε models need 40% more computer time than the B-L model, the k-ω model requires at least 65% more time due to slower rate of convergence. It is found that the heat transfer coefficient exhibits a strong spanwise as well as streamwise variation for both blades and all turbulence models.

Aerothermal Effect of Cavity Welding Beads on a Transonic Squealer Tip

2020 ◽  
Author(s):  
Joao Vieira ◽  
John Coull ◽  
Peter Ireland ◽  
Eduardo Romero
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
Blade Tip ◽  
Mass Flow Rates

Abstract High pressure turbine blade tips are critical for gas turbine performance and are sensitive to small geometric variations. For this reason, it is increasingly important for experiments and simulations to consider real geometry features. One commonly absent detail is the presence of welding beads on the cavity of the blade tip, which are an inherent by-product of the blade manufacturing process. This paper therefore investigates how such welds affect the Nusselt number, film cooling effectiveness and aerodynamic performance. Measurements are performed on a linear cascade of high pressure turbine blades at engine realistic Mach and Reynolds numbers. Two cooled blade tip geometries were tested: a baseline squealer geometry without welding beads, and a case with representative welding beads added to the tip cavity. Combinations of two tip gaps and several coolant mass flow rates were analysed. Pressure sensitive paint was used to measure the adiabatic film cooling effectiveness on the tip, which is supplemented by heat transfer coefficient measurements obtained via infrared thermography. Drawing from all of this data, it is shown that the weld beads have a generally detrimental impact on thermal performance, but with local variations. Aerodynamic loss measured downstream of the cascade is shown to be largely insensitive to the weld beads.

An Experimental Investigation of a New Hybrid Film Cooling Scheme

2010 ◽  
Author(s):  
M. Ghorab ◽  
I. Hassan ◽  
T. Lucas
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Hybrid Film ◽  
Density Ratio ◽  
Thermochromic Liquid Crystal ◽  
Hybrid Scheme ◽  
Cooling Performance ◽  
Average Heat ◽  
Bending Effect ◽  
Turbine Airfoils

This paper presents an experimental investigation of the film cooling performance of a New Hybrid Film Cooling Scheme using Thermochromic Liquid Crystal technique. The new scheme has been designed to improve the film cooling performance of gas turbine airfoils. The scheme includes two consecutive film hole configurations with interior bending. The cooling performance of the new scheme was analyzed across blowing ratios of 0.5, 1.0 and 1.5, at a density ratio of 0.94. The results showed that the new scheme enhanced the local and the laterally averaged film cooling performance in terms of effectiveness, and net heat flux reduction in compared to other film hole configurations. The bending effect of the new scheme throttled the secondary flow causing it to spread widely over the downstream surfaces, hence enhancing the film cooling performance at low and high blowing ratios. The hybrid scheme provided an average heat transfer ratio near unity over the downstream surfaces at low and high blowing ratios.

scholarly journals Numerical Prediction of Film Cooling Effectiveness and the Associated Aerodynamic Losses With a Three-Dimensional Calculation Procedure

1990 ◽  
Author(s):  
G. H. Dibelius ◽  
R. Pitt ◽  
B. Wen
Keyword(s):  
Experimental Data ◽  
Film Cooling ◽  
Reverse Flow ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Temperature Pattern ◽  
Main Stream ◽  
Cooling Efficiency ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Losses

Film cooling of turbine blades by injecting air through holes or slots affects the main stream flow. A numerical model has been developed to predict the resulting three-dimensional flow and the temperature pattern under steady flow conditions. An elliptic procedure is used in the near injection area to include reverse flow situations, while in the upstream area as well as far downstream a partial-parabolic procedure is applied. As first step an adiabatic wall has been assumed as boundary condition, since for this case experimental data are readily available for comparison. At elevated momentum blowing rates, zones of reverse flow occur downstream of the injection holes resulting in a decrease of cooling efficiency. A variation of the relevant parameters momentum blowing rate m, injection angle α and ratio of hole spacing to diameter s/d revealed the combination of m ≈ 1, α ≈ 30° and s/d ≈ 2 to be the optimum with respect to the averaged cooling efficiency and to the aerodynamic losses. Cooling is more efficient with slots than with a row of holes not considering the related problems of manufacture and service life. The calculated temperature patterns compare well with the experimental data available.

Sign in / Sign up

Export Citation Format

Share Document