CONDENSATION HEAT TRANSFER IN SMALL DIAMETER TUBES

1998 ◽  
Author(s):  
Ralph L. Webb ◽  
Ming Zhang ◽  
Ram Narayanamurthy
Keyword(s):  
Heat Transfer ◽  
Small Diameter ◽  
Condensation Heat Transfer

A Experimental Study of Condensation Heat Transfer and Pressure Drop in a Single High Aspect Ratio Micro-Channel for Refrigerant R134a

2006 ◽  
Author(s):  
Sourav Chowdhury ◽  
Ebrahim Al-Hajri ◽  
Serguei Dessiatoun ◽  
Amir Shooshtari ◽  
Michael Ohadi
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Small Diameter ◽  
Hydraulic Diameter ◽  
Condensation Heat Transfer ◽  
Small Scale ◽  
Measurement Instruments

Only recently, experimental data is available in open literature in condensation of various refrigerants in small hydraulic diameter microchannels. The phenomenon of two-phase flow and heat transfer mechanism in small diameter microchannels (< 1 mm) may be different than that in conventional tube sizes due to increasing dominance of several influencing parameters like surface tension, viscosity etc. This paper presents an on-going experimental study of condensation heat transfer and pressure drop of refrigerant R134a is a single high aspect ratio rectangular microchannel of hydraulic diameter 0.7 mm and aspect ratio 7:1. This data will help explore the condensation phenomenon in microchannels that is necessary in the design and development of small-scale heat exchangers and other compact cooling systems. The inlet vapor qualities between 20% and 80% and mass fluxes of 130 and 200 kg/m2s have been studied at present. The microchannel outlet conditions are maintained at close to thermodynamic saturated liquid state through a careful experimental procedure. A unique process for fabrication of the microchannel involving milling and electroplating steps has been adopted to maintain the channel geometry close to design values. Measurement instruments are well-calibrated to ensure low system energy balance error, uncertainty and good repeatability of test data. The trends of data recorded are comparable to that found in recent literature on similar dimension tubes.

scholarly journals Correlation for Condensation Heat Transfer in a 4.0 mm Smooth Tube and Relationship with R1234ze(E), R404A, and R290

2018 ◽  
Vol 8 (11) ◽  
pp. 2267 ◽  
Author(s):  
Norihiro Inoue ◽  
Masataka Hirose ◽  
Daisuke Jige ◽  
Junya Ichinose
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Small Diameter ◽  
Saturation Temperature ◽  
Condensation Heat Transfer ◽  
Smooth Tube ◽  
General Correlation ◽  
Condensation Heat Transfer Coefficient

In this study, the condensation heat transfer coefficient and pressure drop characteristics of a 4 mm outside diameter smooth tube, using R32, R152a, R410A, and R1234ze(E) refrigerants, were examined. Condensation heat transfer coefficients and pressure drops were measured at a saturation temperature of 35 °C, in the region of mass velocities from 100 to 400 kg m−2s−1. The frictional pressure drop, and the condensation heat transfer from the new measurements, using R1234ze(E) as a refrigerant, were compared with those of R32, R152a, and R410A, in the smooth tube. Experimental values of condensation heat transfer coefficient of smooth tube were also compared to the predicted values obtained using the previously established correlations. The previous correlation from Cavallini et al., for the condensation heat transfer coefficient of small-diameter smooth tube, was estimated to be within ±30%. However, the general correlation, which can be easily predicted, for condensation heat transfer inside small-diameter smooth tubes, was suggested, and the relationship of the general correlation was compared with data for R1234ze(E) obtained by us, and R404A and R290 obtained by other researchers.

Sign in / Sign up

Export Citation Format

Share Document