BUBBLE DYNAMICS AND POOL BOILING HEAT TRANSFER FROM TRIANGULAR AND RECTANGULAR GROOVED SURFACES

2018 ◽  
Author(s):  
Sathyabhama A ◽  
Satyajit Malode
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Bubble Dynamics ◽  
Pool Boiling ◽  
Pool Boiling Heat Transfer

Pore-Scale Simulation on Pool Boiling Heat Transfer and Bubble Dynamics in Open-Cell Metal Foam by Lattice Boltzmann Method

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Jie Qin ◽  
Zhiguo Xu ◽  
Xiaofei Ma
Keyword(s):  
Heat Transfer ◽  
Lattice Boltzmann ◽  
Boiling Heat Transfer ◽  
Bubble Dynamics ◽  
Metal Foam ◽  
Pool Boiling ◽  
Open Cell ◽  
Pool Boiling Heat Transfer ◽  
Boltzmann Method ◽  
Foam Thickness

Abstract Based on the newly developed geometrical model of open-cell metal foam, pool boiling heat transfer in open-cell metal foam, considering thermal responses of foam skeletons, is investigated by the phase-change lattice Boltzmann method (LBM). Pool boiling patterns are obtained at different heat fluxes. The effects of pore density and foam thickness on bubble dynamics and pool boiling heat transfer are revealed. The results show that “bubble entrainment” promotes fluid mixing and bubble sliding inside metal foam. Based on force analysis, the sliding bubble is pinned on the heating surface and cannot lift off completely at high heat flux due to the increasing surface tension force. Pool boiling heat transfer coefficient decreases with increasing pore density and foam thickness due to high bubble escaping resistance.

Experimental Study of Effect of Nucleation Site Size on Bubble Dynamics during Nucleate Pool Boiling Heat Transfer

2014 ◽  
Vol 592-594 ◽  
pp. 1596-1600 ◽  
Author(s):  
Abdul Najim ◽  
Anil R. Aacharya
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Bubble Dynamics ◽  
Bubble Diameter ◽  
Pool Boiling ◽  
Growth Period ◽  
Nucleation Site ◽  
Hypodermic Needle ◽  
Nucleate Pool Boiling ◽  
Pool Boiling Heat Transfer

In this paper, effect of nucleation site size on bubble dynamics during nucleate pool boiling heat transfer in saturated water is studied experimentally. Single bubble was generated using right angle tip of a hypodermic needle as a nucleation site. The hypodermic needles were used of inner diameters 0.413mm, 0.514mm, and 0.603 mm with a constant depth of 25mm. The bubble dynamics was studied using SONY Cyber-shot DSC-H100 camera operating at 30 frames per second at atmospheric pressure and at a wall superheat of 5K. The results show that, bubble diameter, bubble height and bubble volume increases with increase in diameter of nucleation site. The bubble growth period is found to be dependent on nucleation site size, and it decreases with increase in diameter of nucleation site. This happens because as volume of vapor bubble increases, buoyancy force starts dominates the capillary force and bubble detaches earlier. Effect of nucleation site size on bubble departure diameter and bubble release frequency is also discussed.

Characteristics of Pool Boiling Bubble Dynamics in Bead Packed Porous Structures

2010 ◽  
Vol 133 (3) ◽  
Author(s):  
Calvin H. Li ◽  
Ting Li ◽  
Paul Hodgins ◽  
G. P. Peterson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Computer Simulation ◽  
Boiling Heat Transfer ◽  
Bubble Dynamics ◽  
Pool Boiling ◽  
Theoretical Models ◽  
High Heat Flux ◽  
Porous Structures ◽  
Pool Boiling Heat Transfer

Spherical glass and copper beads have been used to create bead packed porous structures for an investigation of two-phase heat transfer bubble dynamics under geometric constraints. The results demonstrated a variety of bubble dynamics characteristics under a range of heating conditions. The bubble generation, growth, and detachment during the nucleate pool boiling heat transfer have been filmed, the heating surface temperatures and heat flux were recorded, and theoretical models have been employed to study bubble dynamic characteristics. Computer simulation results were combined with experimental observations to clarify the details of the vapor bubble growth process and the liquid water replenishing the inside of the porous structures. This investigation has clearly shown, with both experimental and computer simulation evidence, that the millimeter scale bead packed porous structures could greatly influence pool boiling heat transfer by forcing a single bubble to depart at a smaller size, as compared with that in a plain surface situation at low heat flux situations, and could trigger the earlier occurrence of critical heat flux by trapping the vapor into interstitial space and forming a vapor column net at high heat flux situations. The results also proved data for further development of theoretical models of pool boiling heat transfer in bead packed porous structures.

Characteristics of Pool Boiling Bubble Dynamics in Bead Packed Porous Structures

2009 ◽  
Author(s):  
Calvin H. Li ◽  
Ting Li ◽  
Paul Hodgins ◽  
G. P. Peterson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Bubble Dynamics ◽  
Pool Boiling ◽  
Heating Surface ◽  
Theoretical Models ◽  
Porous Structures ◽  
Pool Boiling Heat Transfer ◽  
Simulation Results

Spherical glass and copper beads have been used to create bead packed porous structures for an investigation of two-phase heat transfer bubble dynamics under geometric constraints. The results demonstrated a variety of bubble dynamics characteristics under a range of heating conditions. At low heat flux of 18.9 kW/m2, a single spherical bubble formed at nucleation sites of a heating surface and departed to the interstitial spaces of porous structure. When heat flux increased to 47 kW/m2, a single bubble grew into a Y shape between beads layers and connected with others to generate a horizontal vapor column. As heat flux reached 76.3 kW/m2, vertical vapor columns obtained strong momentum to form several major vapor escaping arteries, and glass beads were pushed upward by the vapor in the escaping arteries. According to Zuber’s hydrodynamics theory, choking will take place when the size of vapor columns reaches a certain value that is comparable to the critical hydrodynamic wavelength of the vapor column in plain surface pool boiling. The experimental and simulation results of this investigation illustrated that, under the geometric constrains of bead packed porous structures, similar characteristics had been induced to trigger the earlier occurrence of vapor column chocking inside porous structures. The bubble generation, growth, and detachment during the nucleate pool boiling heat transfer have been filmed, the heating surface temperatures and heat flux were recorded, and theoretical models have been employed to study bubble dynamic characteristics. Computer simulation results were combined with experimental observations to clarify the details of the vapor bubble growth process and the liquid water replenishing the inside of the porous structures. This investigation has clearly shown, with both experimental and computer simulation evidence, that the millimeter scale bead packed porous structures could greatly influence pool boiling heat transfer by forcing a single bubble to depart at a smaller size as compared to that in a plain surface situation at low heat flux situations, and could trigger the earlier occurrence of critical heat flux (CHF) by trapping the vapor into interstitial space and forming a vapor column net. The results also proved data for further development of theoretical models of pool boiling heat transfer in bead packed porous structures.

scholarly journals Effect on bubble dynamics during pool boiling heat transfer in a novel aqueous binary mixture of surfactants

2020 ◽  
Vol 814 ◽  
pp. 012045
Author(s):  
Prashant B. Pawar ◽  
Ganesh N. Rakate ◽  
Sujit V. Yadav ◽  
Vivek S. Gondkar ◽  
Suresh L. Chittewar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Binary Mixture ◽  
Boiling Heat Transfer ◽  
Bubble Dynamics ◽  
Pool Boiling ◽  
Pool Boiling Heat Transfer
Sign in / Sign up

Export Citation Format

Share Document