Initial Stages of Growth of Gallium Nitride via Iodine Vapor Phase Epitaxy

2004 ◽  
Vol 831 ◽  
Author(s):  
WJ Mecouch ◽  
BJ Rodriguez ◽  
ZJ Reitmeier ◽  
J-S Park ◽  
RF Davis ◽  
...  

ABSTRACTThin layers of GaN have been deposited on 1μm thick MOVPE GaN(0001) thin film substrates using a novel vertical iodine vapor phase epitaxy system. The system features three concentric flow zones that separate the reactant gasses until they reach the substrate. Hydrogen flows through the innermost zone to deliver iodine vapor from an external bubbler to the molten Ga maintained at ∼1050°C and GaI to the substrate; high-purity ammonia flows through the outermost zone; nitrogen flows through the middle zone to prevent reaction between the growth species at the GaI nozzle. GaN growth was found to be a function of time, with decreasing concentration of iodine the likely cause of a decrease in growth rate at longer growth times. The step-and-terrace microstructure of the MOVPE seeds was replaced with a smooth morphology film after the shortest growth experiment. Star-shaped features with hexagonal symmetry grew on the surface with increasing growth time. These features became the tops of hexagonal pyramids; these pyramids grew competitively and dominated the final growth surface. The surface of the films grown for the longest period contained a step-and-terrace microstructure; however, the density of steps of was lower than that on the surface of underlying MOVPE substrate.

MRS Advances ◽  
2019 ◽  
Vol 4 (10) ◽  
pp. 593-599 ◽  
Author(s):  
A. Grundmann ◽  
D. Andrzejewski ◽  
T. Kümmell ◽  
G. Bacher ◽  
M. Heuken ◽  
...  

ABSTRACTThe 2D transition metal dichalcogenide (TMDC) tungsten disulfide (WS2) has attracted great interest due to its unique properties and prospects for future (opto)electronics. However, compared to molybdenum disulfide (MoS2), the development of a reproducible and scalable deposition process for 2D WS2 has not advanced very far yet. Here, we report on the systematic investigation of 2D WS2 growth on hydrogen (H2)-desorbed sapphire (0001) substrates using a hydrogen sulfide (H2S)-free metal-organic vapor phase epitaxy (MOVPE) process in a commercial AIXTRON planetary hot-wall reactor in 10 × 2" configuration. Tungsten hexacarbonyl (WCO, 99.9 %) and di-tert-butyl sulfide (DTBS, 99.9999 %) were used as MO sources, nitrogen (N2) was selected as carrier gas for the deposition processes (standard growth time 10 h). In an initial study, the impact of growth temperature on nucleation and growth was investigated and an optimal value of 820 °C was found. The influence of the WCO flow on lateral growth was investigated. The aim was to maximize the edge length of triangular crystals as well as the total surface coverage. Extending gradually the growth time up to 20 h at optimized WCO flow conditions yields fully coalesced WS2 samples without parasitic carbon-related Raman peaks and with only sparse bilayer nucleation. After substrate removal, a fully coalesced WS2 film was implemented into a light-emitting device showing intense red electroluminescence (EL).


2005 ◽  
Vol 475-479 ◽  
pp. 1729-1732
Author(s):  
J.F. Wang ◽  
G.M. Lalev ◽  
M. Isshiki

The quaternary HgCdZnTe (MCZT) epilayer was successfully grown on lattice matched Cd0.96Zn0.04Te/Si(111) substrates using isothermal vapor phase epitaxy (ISOVPE) method. It was found that Si wafer is an excellent barrier against Hg and Cd diffusion. Cross-sectional images reveal a flat and well-distinguished interface between MCZT and Si, and voids formed due to interdiffusion was not observed in MCZT layer above the Si wafer. It was demonstrated that it was possible to yield an almost homogeneous MCZT epilayer without compositional gradient by selecting suitable growth time.


2020 ◽  
Vol 50 (2) ◽  
Author(s):  
Adriana Łozińska ◽  
Mikołaj Badura ◽  
Joanna Jadczak ◽  
Katarzyna Bielak ◽  
Beata Ściana

In the presented work, an optical approach of stress determining in metalorganic vapor phase epitaxy (MOVPE) grown quantum cascade laser (QCL) structures was reported. In the case of such sophisticated structures containing hundreds of thin layers, it is important to minimize the stress generated in the QCL core. Techniques enabling determination of stress in such thin layers as those described in the article are photoluminescence and Raman spectroscopies. Based on Raman shift or changes in photoluminescence signal, it is possible to analyze stress occurring in the structure.


2010 ◽  
Vol 312 (16-17) ◽  
pp. 2324-2327 ◽  
Author(s):  
Rui Masuda ◽  
Tetsuo Fujii ◽  
Naoki Yoshii ◽  
Yoshinao Kumagai ◽  
Akinori Koukitu

2002 ◽  
Vol 14 (13-14) ◽  
pp. 991-993 ◽  
Author(s):  
H.-M. Kim ◽  
D.S. Kim ◽  
Y.S. Park ◽  
D.Y. Kim ◽  
T.W. Kang ◽  
...  

Author(s):  
Wondwosen Metaferia ◽  
Anna K. Braun ◽  
John Simon ◽  
Corinne E. Packard ◽  
Aaron J. Ptak ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document