Deformation Induced Dilatations and New Observations on Fracture In Compression in Metallic Glasses at Low Temperatures

1981 ◽  
Vol 8 ◽  
Author(s):  
Janez Megusar ◽  
Ali S. Argon ◽  
Nicholas J. Grant
Keyword(s):  
Fracture Surface ◽  
Metallic Glasses ◽  
Low Temperatures ◽  
Fracture Surfaces ◽  
Dilatometric Method ◽  
Characteristic Features

ABSTRACTDeformation induced dilatations were measured on a Pd-Cu-Si glass by a differential dilatometric method during crystallization. At large pre-strains, these dilatations are large and of the order of 20%. Fracture surfaces of specimens in compression show either the characteristic features of tensile separation or evidence for repeated nucleation of fracture. Rubbing was observed only in a small fraction of a fracture surface.

Scanning tunneling microscope observations of metallic glass fracture surfaces

1993 ◽  
Vol 8 (10) ◽  
pp. 2543-2553 ◽  
Author(s):  
D.M. Kulawansa ◽  
J.T. Dickinson ◽  
S.C. Langford ◽  
Yoshihisa Watanabe
Keyword(s):  
Fracture Surface ◽  
Metallic Glass ◽  
Metallic Glasses ◽  
Scanning Tunneling Microscope ◽  
Shear Bands ◽  
Scanning Tunneling ◽  
Tunneling Microscope ◽  
Fracture Surfaces ◽  
Glass Fracture ◽  
Shear Instabilities

We report scanning tunneling microscope observations of fracture surfaces formed during catastrophic crack growth in three metallic glasses: Ni56Cr18Si22B4, Co69Fe4Ni1Mo2B12Si12, and Fe78B13Si9. Macroscopically, the first two glasses fail along a slip band formed during loading and display a characteristic, μm-scale pattern of vein-like ridges; in contrast, Fe78B13Si9 displays little slip prior to fracture, and its fracture surface shows a μm-scale chevron pattern of steps. STM observations of fracture surfaces of all three materials show nm-scale grooves. The grooves in Co69Fe4Ni1Mo2B12Si12 are especially prominent and display stepped edges which we attribute to the intersection of shear bands with the surface. STM observations of the vein-like features on Ni56Cr18Si22B4 also show stepped edges. We attribute the vein features to the interaction of adjacent crack fingers in which the material between adjacent fingers fails in plane stress. The origin of the grooves is uncertain, but may be due to other shear instabilities along crack fingers.

ULTRASONIC STUDIES OF METALLIC GLASSES AT LOW TEMPERATURES

1981 ◽  
Vol 42 (C5) ◽  
pp. C5-517-C5-521
Author(s):  
G. Park ◽  
A. Hikata ◽  
C. Elbaum
Keyword(s):  
Metallic Glasses ◽  
Low Temperatures

Research on Anisotropic Fracture Mechanical Behavior of Cortical Bone with Combined Method of Fractal and Gray Level Co-Occurrence Matrix

2021 ◽  
Vol 11 (1) ◽  
pp. 67-75
Author(s):  
Dagang Yin ◽  
Bin Chen ◽  
Huifen Zhou
Keyword(s):  
Mechanical Properties ◽  
Fracture Surface ◽  
Cortical Bone ◽  
Fracture Mechanisms ◽  
Gray Level ◽  
Combined Method ◽  
Characteristic Parameters ◽  
Fracture Surfaces ◽  
Anisotropic Fracture ◽  
Occurrence Matrix

The irregular fracture surface of cortical bone, which is caused by complex multilevel micro-nanostructure, reflects the mechanical properties and fracture mechanisms. It is of great significance to characterize some characteristic parameters from the fracture surfaces of bone. In this research, anisotropic fracture mechanical properties of bovine femoral cortical bone along transverse, longitudinal and radial direction are firstly obtained by three-point bend experiment. Then the fracture routes and fracture surfaces are observed by scanning electron microscope. The observation shows that the formed fracture surfaces, which are caused by different crack routes, are extremely rough and have complex textures. Lastly, the combined method of fractal and gray level co-occurrence matrix are adopted to describe the morphology of fracture surface of cortical bone objectively and quantitatively. It is shown that the fracture surface of cortical bone has obvious fractal characteristics and four statistical texture feature parameters (contrast,angular second moment, correlation and entropy) of GLCM of fracture surfaces can describe a certain fracture texture character. The relationship between the characteristic parameters and macroscopic mechanical properties are established. The quantitative analysis and automatic class identification for the fracture surfaces of cortical bone can be achieved.

Scanning Auger and Xps Studies of Fracture Surfaces of B4C Hot Pressed with Excess Carbon

1989 ◽  
Vol 153 ◽  
Author(s):  
Benjamin M. DeKoven ◽  
Eric A. Ness ◽  
David D. Hawn
Keyword(s):  
Fracture Surface ◽  
Boron Carbide ◽  
Carbon Content ◽  
Low Dose ◽  
Xps Spectra ◽  
Excess Carbon ◽  
Fracture Surfaces ◽  
Four Point Bending ◽  
Hardness Values

AbstractA series of boron carbide materials was hot pressed with 0-7% excess carbon. The strength of each material was determined by four point bending, and found to decrease from about 600MPa to 300MPa as the carbon content increased from 0% to 7%. Diamond indentation yielded hardness values that decreased from 28.3 to 25.OGPa and toughness values that increased from 3.5 to 4.5 MPa√mover the same carbon range. Each sample was fractured in situ in ultrahigh vacuum (UHV) and examined by scanning Auger microanalysis (SAM) and XPS to determine both the elemental and chemical state distributions. For the samples with excess carbon, localized carbonrich regions are observed on fracture surfaces by SAM. XPS reveals a 50% enhancement of excess carbon on the fracture surface compared to the bulk for the sample with 7% excess carbon. A correlation was observed between surface carbon composition and the bulk toughness and hardness. The C(ls) XPS spectra were utilized to determine the nature of carbon in B4C on freshly fractured and Ne+ bombarded surfaces. Two distinct peaks were observed in the C(ls) region. Low dose ion bombardment resulted in a single broad C(ls) peak at the midpoint of the two initial peaks. It can be inferred from this data that there are C-C-C intericosahedral linkages in B4C.

New Computational Procedures for Evaluation of Fracture Surfaces of the Drop Weight Tear Test of the Piping Steel

2011 ◽  
Author(s):  
Pavel Zˇidli´k ◽  
Petr Ferfecki ◽  
Bohumi´r Strnadel
Keyword(s):  
Fracture Surface ◽  
Ductile Fracture ◽  
Unstable Fracture ◽  
Fracture Surfaces ◽  
Drop Weight ◽  
Highly Sensitive ◽  
Drop Weight Tear Test ◽  
Computational Procedures ◽  
New Procedures

Drop weight tear test (DWTT) is one of the standard methods for evaluation of the ductility of large-dimensional structural components, such as pipelines used for gas and/or oil transportation. In general, the pipelines are even used in places with temperatures close to −40 °C, and in such environments, it is necessary to guarantee the resistance of the material used for pipeline against the initiation of unstable fracture. Currently, the percentage portion of the ductile fracture of the DWTT specimen is determined by an expert evaluator. The objective of this paper is to introduce new procedures working on the principle of deterministic, statistical and fractal description of the fracture surface. For the proposed computational procedures, the fracture surface of the test specimen is scanned at the macroscopic level using the 3D-Cam scanner. The newly investigated procedures show highly sensitive to the determination of the percentage portion of the ductile fracture on the tested DWTT specimens. The developed procedures to assess the fracture surfaces of the DWTT specimens contributes to making the results of this test more correct, objective and also increases the reliability and safety of the manufactured pipelines.

Self-affine Fracture Surface Parameters and Their Relationship with Microstructure in a Cast Aluminum Alloy

2002 ◽  
Vol 17 (6) ◽  
pp. 1276-1282 ◽  
Author(s):  
M. Hinojosa ◽  
J. Aldaco
Keyword(s):  
Aluminum Alloy ◽  
Fracture Surface ◽  
The Self ◽  
Cast Aluminum Alloy ◽  
Cast Aluminum ◽  
Force Microscopy ◽  
Fracture Surfaces ◽  
Atomic Force ◽  
Roughness Exponent

The possible role of microstructural features in determining the self-affinity of the fracture surface of a cast aluminum alloy is explored in this work. Fracture surfaces generated both in tension and impact tests were topometrically analyzed by atomic force microscopy, scanning electron microscopy, and stylus profilometry. The roughness exponent exhibited the “universal” value ζ ≈ 0.78, and the correlation length ζ was of the order of the grain size. The brittle intermetallic compounds known to be important in crack initiation did not show any correlation with the self-affine parameters of the resulting fracture surfaces in this particular case.

scholarly journals The Evaluation of the Fracture Surface in the AW-6060 T6 Aluminium Alloy under a Wide Range of Loads

Metals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 324 ◽  
Author(s):  
Marcin Chybiński ◽  
Łukasz Polus ◽  
Maria Ratajczak ◽  
Piotr Sielicki
Keyword(s):  
Fracture Surface ◽  
Strain Rate ◽  
Aluminium Alloy ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Tensile Loading ◽  
Engineering Structures ◽  
Fracture Surfaces ◽  
Wide Range ◽  
Scanning Electron

The present study focused on the behaviour of the AW-6060 aluminium alloy in peak temper condition T6 under a wide range of loads: tensile loading, projectile and explosion. The alloy is used as a structural component of civil engineering structures exposed to static or dynamic loads. Therefore, it was crucial to determine the material’s behaviour at low and intermediate rates of deformation. Despite the fact that the evaluation of the strain rate sensitivity of the AW-6060 aluminium alloy has already been discussed in literature, the authors of this paper wished to further investigate this topic. They conducted tensile tests and confirmed the thesis that the AW-6060 T6 aluminium alloy has low strain rate sensitivity at room temperature. In addition, the fracture surfaces subjected to different loading (tensile loading, projectile and explosion) were investigated and compared using a scanning electron microscope, because the authors of this paper were trying to develop a new methodology for predicting how samples had been loaded before failure occurred based on scanning electron microscopy (SEM) micrographs. Projectile and explosion tests were performed mainly for the SEM observation of the fracture surfaces. These tests were unconventional and they represent the originality of this research. It was found that the type of loading had an impact on the fracture surface.

Sign in / Sign up

Export Citation Format

Share Document