Annealing induced structural changes and microcracking in Mo-Mo3Si

2002 ◽  
Vol 753 ◽  
Author(s):  
X.-L. Wang ◽  
J. H. Schneibel ◽  
Y. D. Wang ◽  
J. W. Richardson
Keyword(s):  
Electron Microscopy ◽  
Experimental Data ◽  
High Temperature ◽  
Structural Changes ◽  
Thermal Stresses ◽  
Annealing Temperature ◽  
Composition Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

ABSTRACTCast Mo-Mo3Si intermetallic composites develop microcracks after annealing at high temperature. Neutron diffraction, x-ray diffraction, composition analysis, and scanning electron microscopy have been used to characterize the structural changes induced by annealing of Mo-Mo3Si. It is shown that the observed cracking cannot be attributed to differential thermal stresses that developed on cooling from the annealing temperature. Instead, the experimental data suggest that the cracks were initiated at high temperature, possibly due to diffusion of Si atoms from supersaturated α-Mo to Mo3Si.

scholarly journals A Study on the Characteristics of Cu–Mn–Dy Alloy Resistive Thin Films

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 118 ◽  
Author(s):  
Ho-Yun Lee ◽  
Chi-Wei He ◽  
Ying-Chieh Lee ◽  
Da-Chuan Wu
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Annealing Temperature ◽  
Phase Evolution ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Temperature Coefficient Of Resistance ◽  
X Ray ◽  
Transmission Electronmicroscopy ◽  
Scanning Electron

Cu–Mn–Dy resistive thin films were prepared on glass and Al2O3 substrates, which wasachieved by co-sputtering the Cu–Mn alloy and dysprosium targets. The effects of the addition ofdysprosium on the electrical properties and microstructures of annealed Cu–Mn alloy films wereinvestigated. The composition, microstructural and phase evolution of Cu–Mn–Dy films werecharacterized using field emission scanning electron microscopy, transmission electronmicroscopy and X-ray diffraction. All Cu–Mn–Dy films showed an amorphous structure when theannealing temperature was set at 300 °C. After the annealing temperature was increased to 350 °C,the MnO and Cu phases had a significant presence in the Cu–Mn films. However, no MnO phaseswere observed in Cu–Mn–Dy films at 350 °C. Even Cu–Mn–Dy films annealed at 450 °C showedno MnO phases. This is because Dy addition can suppress MnO formation. Cu–Mn alloy filmswith 40% dysprosium addition that were annealed at 300 °C exhibited a higher resistivity of ∼2100 μΩ·cm with a temperature coefficient of resistance of –85 ppm/°C.

SIZE-INDUCED EFFECTS IN NANOSTRUCTURED NiFe2O4

2010 ◽  
Vol 24 (30) ◽  
pp. 5973-5985
Author(s):  
M. GUNES ◽  
H. GENCER ◽  
T. IZGI ◽  
V. S. KOLAT ◽  
S. ATALAY
Keyword(s):  
Electron Microscopy ◽  
Annealing Temperature ◽  
Structural Parameters ◽  
Hydrothermal Process ◽  
Lattice Parameter ◽  
Effect Of Temperature ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

NiFe 2 O 4 nanoparticles were successfully prepared by a hydrothermal process, and the effect of temperature on them was studied. The particles were annealed at various temperatures ranging from 413 to 1473 K. Studies were carried out using powder X-ray diffraction, scanning electron microscopy, infrared spectroscopy, differential thermal analysis, thermogravimetric analysis and a vibrating sample magnetometer. The annealing temperature had a significant effect on the magnetic and structural parameters, such as the crystallite size, lattice parameter, magnetization and coercivity.

A Study of Phase Reactions in a Complex 4.5 Al–3.5 Ti–Ni Base Alloy

1960 ◽  
Vol 4 ◽  
pp. 233-243
Author(s):  
John F. Radavich ◽  
W. J. Boesch
Keyword(s):  
Electron Microscopy ◽  
High Temperature ◽  
Structural Changes ◽  
Base Alloy ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
High Temperature Alloy ◽  
X Ray ◽  
Nickel Base ◽  
Precipitated Phases

AbstractAn investigation of the phase changes in a complex aluminum-titanium-hardened nickel-base high-temperature alloy was carried out after solutioning at high temperatures and aging at lower temperatures. The physical distribution and size of the precipitated phases were studied by electron microscopy. X-ray diffraction and fluorescence analyses were carried out on chemically extracted residues. The results of the xtructure changes as well as correlation of some physical properties with the structural changes are presented.

A Porous TiO2 Coating with Vermiform Morphology Formed on Ti through Micro-Arc Oxidation

2013 ◽  
Vol 652-654 ◽  
pp. 1818-1821
Author(s):  
Zhen Fei Liu ◽  
Wei Qiang Wang ◽  
Min Qi
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Temperature ◽  
Rutile Phase ◽  
Sodium Tetraborate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Porous Titania ◽  
Micro Arc Oxidation ◽  
Scanning Electron

A porous titania (TiO2) coating with vermiform slots was prepared on the Ti substrate through micro-arc oxidation (MAO) treatment using sodium tetraborate as electrolyte. Morphologies and phase structure were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. Results show that the rutile phase increases and anatase decreases gradually with increasing MAO time. The electrolyte of sodium tetraborate has significant influence on the formation of vermiform coatings, which determine the corrosive patterning in the first stage during MAO processing. The evolution of vermiform morphology is proposed as followed: some corrosive pores appear on the surface before arcing; afterward, the adjacent micropores in the dense regions link each other due to the high temperature result from continuous arc action; then, the micropores grow up to big pits and combine with each other with increasing MAO treating time; finally, the vermiform morphology forms on the surface of Ti metal.

SiO2ZrO2 Thin Films as Low Temperature NO2 and O3 Sensors

2015 ◽  
Vol 1088 ◽  
pp. 81-85 ◽  
Author(s):  
T.N. Myasoedova ◽  
Victor V. Petrov ◽  
Nina K. Plugotarenko ◽  
Dmitriy V. Sergeenko ◽  
Galina Yalovega ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Scanning Electron Microscopy ◽  
Low Temperature ◽  
Annealing Temperature ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Operating Temperatures ◽  
Scanning Electron

Thin SiO2ZrO2films were prepared, up to 0.2 μm thick, by means of the sol–gel technology and characterized by a Scanning electron microscopy and X-ray diffraction. It is shown the presence of monoclinic, cubic and tetragonal phases of ZrO2in the SiO2matrix. The crystallites sizes depend on the annealing temperature of the film and amount to 35 and 56 nm for the films annealed at 773 and 973 K, respectively. The films resistance is rather sensitive to the presence of NO2and O3impurity in air at lower operating temperatures in the range of 30-60°C.

Biomorphic TiO2 Ceramics Prepared from Cotton Stalk

2012 ◽  
Vol 602-604 ◽  
pp. 526-529
Author(s):  
Qing Wang ◽  
Lin Zhang ◽  
Ya Hui Zhang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Phase Composition ◽  
High Temperature ◽  
Sol Gel ◽  
Cotton Stalk ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carbon Template ◽  
Scanning Electron

Biomorphic TiO2 was prepared by high temperature pyrolysis and a modified sol-gel route. The morphology and microstructure of TiO2 samples were characterized by scanning electron microscopy. The phase composition of the resulting sample was analyzed by X-ray diffraction. The results suggest that the biomorphic TiO2 mainly consists of rutile TiO2, and replicates the shape and part microstructure of the carbon template.

Structural and Morphological Properties of HfxZr1-xO2 Thin Films Prepared by Pechini Route

2010 ◽  
Vol 644 ◽  
pp. 113-116
Author(s):  
L.A. García-Cerda ◽  
Bertha A. Puente Urbina ◽  
M.A. Quevedo-López ◽  
B.E. Gnade ◽  
Leo A. Baldenegro-Perez ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Annealing Temperature ◽  
Precursor Solution ◽  
Dip Coating ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dip Coating Technique ◽  
Scanning Electron

In this study, HfxZr1-xO2 (0 < x < 1) thin films were deposited on silicon wafers using a dip-coating technique and by using a precursor solution prepared by the Pechini route. The effects of annealing temperature on the structure and morphological properties of the proposed films were investigated. HfxZr1-xO2 thin films with 1, 3 and 5 layers were annealed in air for 2 h at 600 and 800 °C and the structural and morphological properties studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD results show that the films have monoclinic and tetragonal structure depending of the Hf and Zr concentration. SEM photographs show that all films consist of nanocrystalline grains with sizes in the range of 6 - 13 nm. The total film thickness is about 90 nm.

scholarly journals Synthesis and Catalase Mimic Activity of MnO2 Nano Powder Prepared by Hydrothermal Process

2019 ◽  
Vol 27 (2) ◽  
pp. 228-237 ◽  
Author(s):  
Rashed T. Rasheed ◽  
Sariya D. Al-Algawi ◽  
Rosul M. N.
Keyword(s):  
Crystal Structure ◽  
Electron Microscopy ◽  
Annealing Temperature ◽  
Hydrothermal Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Atomic Force ◽  
Different Temperatures ◽  
Scanning Electron

Manganese dioxide (MnO2) nanopowder has been synthesized by hydrothermal method. MnO2 was annealed at different temperatures (250, 400, 550, 700˚C). The crystal structure and surface morphology of these nanostructures were characterized by X-ray diffraction (XRD), Atomic Force Microscope (AFM) and Scanning Electron Microscopy (SEM). The catalase mimic activity (catalytic activity) of MnO2 against hydrogen peroxide (H2O2) was studied by using the new method and found that 400˚C is the best annealing temperature.

scholarly journals A novel and facile method for silica nanoparticles synthesis from high temperature vulcanization (HTV) silicon

10.30544/134 ◽  
2016 ◽  
Vol 22 (1) ◽  
pp. 1-8 ◽  
Author(s):  
Mohammad Senemar ◽  
Ali Maleki ◽  
Behzad Niroumand ◽  
Alireza Allafchian
Keyword(s):  
Electron Microscopy ◽  
High Temperature ◽  
Silica Nanoparticles ◽  
Amorphous Silica ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Nanoparticles Synthesis ◽  
Novel Method ◽  
Scanning Electron

This study is introducing a facile and novel method for synthesis of amorphous silica nanoparticles. Silica nanoparticles were synthesized by pyrolysis and combustion of high temperature vulcanization (HTV) silicone at 700 oC for 1 h. The products were investigated employing transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), dynamic light scattering (DLS), X-ray diffraction (XRD), Brunauer Emmett and Teller (BET) test and Fourier Transform Infrared (FTIR) Spectroscopy. The results indicated that the method is capable of synthesis of amorphous silica nanoparticles with sizes of mostly between 10 and 50 nm.

Research on the High-Temperature Compatibility between SiCf and Mo Substrate

2011 ◽  
Vol 393-395 ◽  
pp. 269-273
Author(s):  
Hang Zhou ◽  
Yun Peng Zhang ◽  
Shu Ai Pang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
High Temperature ◽  
Sintered Body ◽  
Synergy Effect ◽  
Chemical Compatibility ◽  
X Ray Diffraction ◽  
X Ray ◽  
New Phase ◽  
Scanning Electron

For preparing Mo-based composite materials enhanced by SiCf by powder metallurgy, the high temperature of chemical compatibility between SiCf and Mo was analyzed by experimental method in order to find whether the reinforcement can effectively composite with matrix for playing synergy effect. The mixture of SiCf and Mo powder was pressed and then sintered. Using scanning electron microscopy (SEM), the fracture surface of the sintered body was observed. Using X-ray diffraction (XRD), the generation of new phase in the sintered body was analyzed. The sinter's density and hardness was tested also. The results are as follows. After 1750°C sintered, SiCf in the presence of metal Mo had decomposed and disappeared. Decomposed products which were C and Si had reacted with Mo to produce mainly compounds Mo5Si3, MoC and a small amount of MoSi2. The disappearance of the SiCf leave more holes in the substrate. Both density and hardness of the sinter are decreased.

Sign in / Sign up

Export Citation Format

Share Document