High Strength Soft Magnetic Composites

2001 ◽  
Vol 674 ◽  
Author(s):  
Ronghai Yu ◽  
Michelle M. Corte-Real ◽  
Adrian Gorea ◽  
Libo Ren ◽  
Azar Parvizi-Majidi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Volume Fraction ◽  
High Strength ◽  
Soft Magnetic Materials ◽  
High Coercivity ◽  
Soft Magnetic ◽  
Fiber Volume ◽  
Magnetic Composites ◽  
Feco Alloys

ABSTRACTThere has been an increasing demand for high temperature soft magnetic materials with mechanical properties better than those of existing commercial materials such as FeCo alloys. We have designed new magnetic composites by reinforcing FeCo alloys with high strength tungsten fibers. The composite materials were fabricated by electrodeposition. In general, the as-deposited composites have a relatively high coercivity Hc and low magnetic permeability μ, because of induced strain during fabrication. After appropriate thermal annealing, the composites have good soft magnetic properties, comparable to commercial bulk alloys. However, the saturation induction is reduced due to the non-magnetic inclusions. The composites also show significant enhancements in yield strength and tensile strength that increases linearly with fiber volume fraction as seen in other common composite materials. In addition, near zero creep is observed at 600 °C under a stress of 600 Mpa. The mechanical properties can be further improved by co-depositing soft magnetic material and Al2O3 onto the fibers. An approximately linear relationship was observed between the coercivity and volume fraction of Al2O3 particles. The square-root relationship was observed between the hardness and the Al2O3 concentration.

Mechanical Properties of Modified Polypropylene Coarse Fiber-Reinforced, High-Strength, Lightweight Concrete

2011 ◽  
Vol 374-377 ◽  
pp. 1499-1506
Author(s):  
Rong Hui Zhang ◽  
Jian Li
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Volume Fraction ◽  
High Strength ◽  
Lightweight Aggregate Concrete ◽  
Fiber Reinforced ◽  
Fiber Volume

In this study, the effect of micro-expansion high strength grouting material (EGM) and Modified polypropylene coarse fiber (M-PP fiber) on the mechanical properties of lightweight concrete are investigated. The influence of EGM and M-PP fiber on compressive strength , flexural strength and drying shrinkage of concrete are researched, and flexural fracture toughness are calculated. Test results show that the effect of EGM and M-PP fiber volume fraction (Vf) on flexural strength and fracture toughness is extremely prominent, compressive strength is only slightly enhanced, and the rate of shrinkage is obviously decreased. It is observed that the shape of the descending branch of load-deflection and the ascending branch of shrinkage-age tends towards gently with the increase of Vf. And M-PP fiber reinforced lightweight aggregate concrete is more economical.

Monitoring of mechanical properties of prestressed glass fiber epoxy composites over 12 months after fabrication

2021 ◽  
pp. 002199832110047
Author(s):  
Mahmoud Mohamed ◽  
Siddhartha Brahma ◽  
Haibin Ning ◽  
Selvum Pillay
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Flexural Strength ◽  
Compressive Residual Stress ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Initial Increase ◽  
Fiber Volume

Fiber prestressing during matrix curing can significantly improve the mechanical properties of fiber-reinforced polymer composites. One primary reason behind this improvement is the generated compressive residual stress within the cured matrix, which impedes cracks initiation and propagation. However, the prestressing force might diminish progressively with time due to the creep of the compressed matrix and the relaxation of the tensioned fiber. As a result, the initial compressive residual stress and the acquired improvement in mechanical properties are prone to decline over time. Therefore, it is necessary to evaluate the mechanical properties of the prestressed composites as time proceeds. This study monitors the change in the tensile and flexural properties of unidirectional prestressed glass fiber reinforced epoxy composites over a period of 12 months after manufacturing. The composites were prepared using three different fiber volume fractions 25%, 30%, and 40%. The results of mechanical testing showed that the prestressed composites acquired an initial increase up to 29% in the tensile properties and up to 32% in the flexural properties compared to the non-prestressed counterparts. Throughout the 12 months of study, the initial increase in both tensile and flexural strength showed a progressive reduction. The loss ratio of the initial increase was observed to be inversely proportional to the fiber volume fraction. For the prestressed composites fabricated with 25%, 30%, and 40% fiber volume fraction, the initial increase in tensile and flexural strength dropped by 29%, 25%, and 17%, respectively and by 34%, 26%, and 21%, respectively at the end of the study. Approximately 50% of the total loss took place over the first month after the manufacture, while after the sixth month, the reduction in mechanical properties became insignificant. Tensile modulus started to show a very slight reduction after the fourth/sixth month, while the flexural modulus reduction was observed from the beginning. Although the prestressed composites displayed time-dependent losses, their long-term mechanical properties still outperformed the non-prestressed counterparts.

Modeling The Microwave Frequency Dielectric Properties of Thermoplastic Composite Materials

1992 ◽  
Vol 269 ◽  
Author(s):  
Mitchell L. Jackson ◽  
Curtis H. Stern
Keyword(s):  
Composite Materials ◽  
Dielectric Properties ◽  
Volume Fraction ◽  
Perturbation Technique ◽  
Resonant Cavity ◽  
Microwave Frequency ◽  
Thermoplastic Composite ◽  
Fiber Volume ◽  
Thermoplastic Matrix ◽  
Rotation Procedure

ABSTRACTMixture models were studied in an effort to predict the microwave frequency permittivities of unidirectional-fiber-reinforced thermoplastic-matrix composite materials as a function of fiber volume fraction, fiber orientation relative to the electric field, and temperature. The permittivities of the constituent fiber and plastic materials were measured using a resonant cavity perturbation technique at 9.4 GHz and at 2.45 GHz. The permittivities of the composite specimens were measured using a reflection cavity technique at 9.4 GHz and at 2.45 GHz. Simple “rule-of-mixtures” models that use the fiber and plastic permittivities have been found to approximate the complex dielectric properties of the composite for varied fiber volume fractions. The permittivities of oriented composites were modeled using a tensor rotation procedure. Composite permittivities were modeled with temperature up to the glass transition temperature of the thermoplastic matrix.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Study of Whiskers to be Used in Composite Materials

2021 ◽  
Vol 316 ◽  
pp. 51-55
Author(s):  
Tamara I. Shishelova ◽  
Vadim V. Fedchishin ◽  
Mikhail A. Khramovskih
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Chemical Properties ◽  
High Strength ◽  
Rapid Expansion ◽  
Physical And Chemical Properties ◽  
Reinforcement Fiber ◽  
Object Of Study ◽  
Physical And Chemical ◽  
And Chemical Properties

Rapid expansion of technologies poses higher requirements to structural materials and items made of them. Conventional materials are being replaced by composite materials (composites). Different additives enhancing the properties of initial materials are used as reinforcement fibers of composites. Utilization of micro-and nanosize particles for production of present-day materials is paid much attention to. Whiskers are among such materials. These crystals have high strength, high chemical and temperature resistance. But for rational utilization of whickers of different chemical composition in composite materials one should know their physical and chemical properties. Objectives of the paper: to study physical and chemical properties of whiskers in different compounds, their composition and structure; to prove experimentally the feasibility of utilizing whiskers as a reinforcement fiber of composite materials. Object of study: specimens of whiskers of silicon nitride (Si3N4), aluminum oxide (Al2O3), aluminum nitride (AlN), and mullite (Al6Si2O13). Methods of investigation: thermal study of specimens, study of mechanical properties and chemical strength, and IR-spectroscopy. Results of study: specimens of whiskers have been studied and their mechanical properties have been tabulated for comparison. Extensive thermal investigation was followed by deduction of regularities and identification of chemical properties of whiskers. IR-spectra of whiskers have been studied and conclusions on molecular composition and on presence of impurities in some whiskers have been made.

scholarly journals Modelling mechanical properties of the multilayer composite materials with the polyamide core

2018 ◽  
Vol 157 ◽  
pp. 02052 ◽  
Author(s):  
Krzysztof Talaśka ◽  
Dominik Wojtkowiak
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
High Strength ◽  
Conveyor Belt ◽  
Complex Model ◽  
Multilayer Composite ◽  
Thermosetting Polymers ◽  
Wide Range ◽  
Belt Conveyors ◽  
Polyamide Film

Due to the wide range of application for belt conveyors, engineers look for many different combinations of mechanical properties of conveyor and transmission belts. It can be made by creating multilayer or fibre reinforced composite materials from base thermoplastic or thermosetting polymers. In order to gain high strength with proper elasticity and friction coefficient, the core of the composite conveyor belt is made of polyamide film core, which can be combined with various types of polymer fabrics, films or even rubbers. In this paper authors show the complex model of multilayer composite belt with the polyamide core, which can be used in simulation analyses. The following model was derived based on the experimental research, which consisted of tensile, compression and shearing tests. In order to achieve the most accurate model, proper simulations in ABAQUS were made and then the results were compared with empirical mechanical characteristics of a conveyor belt. The main goal of this research is to fully describe the perforation process of conveyor and transmission belts for vacuum belt conveyors. The following model will help to develop design briefs for machines used for mechanical perforation.

Effects of Fiber Volume Fraction on Mechanical Properties of SiC-Fiber/Si3N4-Matrix Composites

1994 ◽  
Vol 77 (7) ◽  
pp. 1897-1900 ◽  
Author(s):  
Hockin H. K. Xu ◽  
Claudia P. Ostertag ◽  
Linda M. Braun ◽  
Isabel K. Lloyd
Keyword(s):  
Mechanical Properties ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Matrix Composites ◽  
Fiber Volume ◽  
Sic Fiber ◽  
Si3n4 Matrix

Biomimetic composites inspired by venous leaf

2017 ◽  
Vol 52 (3) ◽  
pp. 361-372 ◽  
Author(s):  
Gongdai Liu ◽  
R Ghosh ◽  
A Vaziri ◽  
A Hossieni ◽  
D Mousanezhad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Stress ◽  
Poisson’S Ratio ◽  
Composite Structures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Poisson's Ratio ◽  
Fiber Volume ◽  
Young’S Moduli

A typical plant leaf can be idealized as a composite having three principal fibers: the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary fibers embedded in a matrix material. This paper introduces a biomimetic composite design inspired by the morphology of venous leafs and investigates the effects of venation morphologies on the in-plane mechanical properties of the biomimetic composites using finite element method. The mechanical properties such as Young’s moduli, Poisson’s ratio, and yield stress under uniaxial loading of the resultant composite structures was studied and the effect of different fiber architectures on these properties was investigated. To this end, two broad types of architectures were used both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions were kept constant and a comparative parametric study was carried out by varying the inclination of the secondary fibers. The results show that the elastic modulus of composite in the direction of main fiber increases linearly with increasing the angle of the secondary fibers. Furthermore, the elastic modulus is enhanced if the secondary fibers are closed, which mimics composites with closed cellular fibers. In contrast, the elastic modulus of composites normal to the main fiber ( x direction) exponentially decreases with the increase of the angle of the secondary fibers and it is little affected by having secondary fibers closed. Similar results were obtained for the yield stress of the composites. The results also indicate that Poisson’s ratio linearly increases with the secondary fiber angle. The results also show that for a constant fiber volume fraction, addition of various tertiary fibers may not significantly enhance the mechanical properties of the composites. The mechanical properties of the composites are mainly dominated by the secondary fibers. Finally, a simple model was proposed to predict these behaviors.

Sign in / Sign up

Export Citation Format

Share Document