Electro-resistive Memory Effect in Colossal Magnetoresistive Films and Performance Enhancement by Post-annealing

2000 ◽  
Vol 648 ◽  
Author(s):  
Shangqing Liu ◽  
Naijuan Wu ◽  
Alex Ignatiev ◽  
Gustavo Tavizon ◽  
Christina Papagianni
Keyword(s):  
Nonvolatile Memory ◽  
Colossal Magnetoresistance ◽  
Room Temperature ◽  
Performance Enhancement ◽  
Electric Pulse ◽  
Zero Magnetic Field ◽  
Colossal Magnetoresistive ◽  
Change Effect ◽  
Electrical Pulses ◽  
And Performance

AbstractColossal magnetoresistive thin films have shown a large electric-pulse-induced resistivity change effect in zero magnetic field and at room temperature. The resistance of such films can be both decreased and increased through multiple nonvolatile intermediate levels by short electrical pulses. The effect provides a potential to develop a novel nonvolatile memory with high density, fast speed, and low power-consumption. An example of this effect has been seen for Pr0.7Ca0.3MnO3 films within which the thermal behavior of the film revealed a method for signal enhancement through annealing. An increase of 700% of the resistance ratio has been demonstrated for a film annealed at 170oC for 30 min. The effect is also observed to be active at room temperature but inefficient at low temperatures, which is interestingly contrary to the behavior of the colossal magnetoresistance effect and provides a clue to understanding the effect.

Materials Characterization and Device Performance of a CMR-Ferroelectric Heterostructure

2001 ◽  
Vol 699 ◽  
Author(s):  
S. R. Surthi ◽  
S. Kotru ◽  
R. K. Pandey
Keyword(s):  
Nonvolatile Memory ◽  
Room Temperature ◽  
Field Effect Transistor ◽  
Film Growth ◽  
Switching Voltage ◽  
Memory Element ◽  
Colossal Magnetoresistive ◽  
Channel Modulation ◽  
Annealing Conditions ◽  
Effect Transistor

Abstract:The films of colossal magnetoresistive La0.67Ca0.33MnO3 (LCMO) and ferroelectric SbSI were grown by pulsed laser deposition method for fabricating their heterostructures. By varying the processing conditions during film growth and controlling subsequently the annealing conditions, the resistivity transport properties of the LCMO films could be greatly modified. Preliminary tests on the ferroelectric field effect transistor (FeFET) based on LCMO-SbSI heterostructure showed that the device behaves like a nonvolatile memory element. The FeFET showed a maximum channel modulation of ∼10% at room temperature, and the switching voltage was less than 2 V.

scholarly journals The frontiers of functionalized graphene-based nanocomposites as chemical sensors

2021 ◽  
Vol 10 (1) ◽  
pp. 330-369
Author(s):  
Norizan M. Nurazzi ◽  
Norli Abdullah ◽  
Siti Z. N. Demon ◽  
Norhana A. Halim ◽  
Ahmad F. M. Azmi ◽  
...  
Keyword(s):  
Electron Mobility ◽  
Room Temperature ◽  
Chemical Sensor ◽  
Performance Enhancement ◽  
Ballistic Transport ◽  
Quantum Hall ◽  
Single Atom ◽  
Research Progress ◽  
Thick Sheet ◽  
High Electron

Abstract Graphene is a single-atom-thick sheet of sp2 hybridized carbon atoms that are packed in a hexagonal honeycomb crystalline structure. This promising structure has endowed graphene with advantages in electrical, thermal, and mechanical properties such as room-temperature quantum Hall effect, long-range ballistic transport with around 10 times higher electron mobility than in Si and thermal conductivity in the order of 5,000 W/mK, and high electron mobility at room temperature (250,000 cm2/V s). Another promising characteristic of graphene is large surface area (2,630 m2/g) which has emerged so far with its utilization as novel electronic devices especially for ultrasensitive chemical sensor and reinforcement for the structural component applications. The application of graphene is challenged by concerns of synthesis techniques, and the modifications involved to improve the usability of graphene have attracted extensive attention. Therefore, in this review, the research progress conducted in the previous decades with graphene and its derivatives for chemical detection and the novelty in performance enhancement of the chemical sensor towards the specific gases and their mechanism have been reviewed. The challenges faced by the current graphene-based sensors along with some of the probable solutions and their future improvements are also being included.

scholarly journals Mechanical and Microstructural Characteristics of Calcium Sulfoaluminate Cement Exposed to Early-Age Carbonation Curing

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3515
Author(s):  
Weikang Wang ◽  
Xuanchun Wei ◽  
Xinhua Cai ◽  
Hongyang Deng ◽  
Bokang Li
Keyword(s):  
Cement Paste ◽  
Pore Diameter ◽  
Performance Enhancement ◽  
Diameter Distribution ◽  
Early Age ◽  
Calcium Sulfoaluminate ◽  
Starting Point ◽  
And Performance ◽  
Curing Pressure ◽  
Carbonation Curing

: The early-age carbonation curing technique is an effective way to improve the performance of cement-based materials and reduce their carbon footprint. This work investigates the early mechanical properties and microstructure of calcium sulfoaluminate (CSA) cement specimens under early-age carbonation curing, considering five factors: briquetting pressure, water–binder (w/b) ratio, starting point of carbonation curing, carbonation curing time, and carbonation curing pressure. The carbonization process and performance enhancement mechanism of CSA cement are analyzed by mercury intrusion porosimetry (MIP), thermogravimetry and derivative thermogravimetry (TG-DTG) analysis, X-ray diffraction (XRD), and scanning electron microscope (SEM). The results show that early-age carbonation curing can accelerate the hardening speed of CSA cement paste, reduce the cumulative porosity of the cement paste, refine the pore diameter distribution, and make the pore diameter distribution more uniform, thus greatly improving the early compressive strength of the paste. The most favorable w/b ratio for the carbonization reaction of CSA cement paste is between 0.15 and 0.2; the most suitable carbonation curing starting time point is 4 h after initial hydration; the carbonation curing pressure should be between 3 and 4 bar; and the most appropriate time for carbonation curing is between 6 and 12 h.

Sign in / Sign up

Export Citation Format

Share Document