Self-control Phenomenon for Crystallinity and Morphology Observed at Epitaxial Growth of BaTiO3 by Alternating Deposition Method

1999 ◽  
Vol 567 ◽  
Author(s):  
K. Shimoyama ◽  
T. Kanda ◽  
M. Iida ◽  
T. Maeda ◽  
K. Yamabe
Keyword(s):  
Epitaxial Growth ◽  
Single Phase ◽  
Three Dimensional ◽  
Self Control ◽  
Deposition Method ◽  
Deposition Cycle ◽  
Surface Smoothness ◽  
Control Crystallization

ABSTRACTWe directly observed self-control crystallization of epitaxial BaTiO3 films during alternate depositions of BaO and TiO2. When TiO2 (or BaO) was supplied excessively, surface crystallinity and smoothness degraded due to three-dimensional (3D) growth. However, when the following BaO (or TiO2) was supplied onto the rough TiO2 (or BaO) surface, the surface smoothness was recovered drastically. It was found that a single phase BaTiO3 film grew by repeating the alternate deposition cycle of excessive supply of both BaO and TiO2. The mechanism of this phenomenon was discussed.

Analysis of Single- and Two-Phase Flows in Turbopump Inducers

1967 ◽  
Vol 89 (4) ◽  
pp. 577-586 ◽  
Author(s):  
P. Cooper
Keyword(s):  
Equation Of State ◽  
Flow Field ◽  
Thermal Effects ◽  
Single Phase ◽  
Fluid Pressure ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Recent Theory ◽  
Two Phase ◽  
Overall Efficiency

A model is developed for analytically determining pump inducer performance in both the single-phase and cavitating flow regimes. An equation of state for vaporizing flow is used in an approximate, three-dimensional analysis of the flow field. The method accounts for losses and yields internal distributions of fluid pressure, velocity, and density together with the resulting overall efficiency and pressure rise. The results of calculated performance of two sample inducers are presented. Comparison with recent theory for fluid thermal effects on suction head requirements is made with the aid of a resulting dimensionless vaporization parameter.

Thermal Characterization of Interlayer Microfluidic Cooling of Three-Dimensional Integrated Circuits With Nonuniform Heat Flux

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Yoon Jo Kim ◽  
Yogendra K. Joshi ◽  
Andrei G. Fedorov ◽  
Young-Joon Lee ◽  
Sung-Kyu Lim
Keyword(s):  
Integrated Circuits ◽  
Mass Flow Rate ◽  
Thermal Management ◽  
Mass Flow ◽  
Flow Rate ◽  
Single Phase ◽  
Hot Spot ◽  
Three Dimensional ◽  
Two Phase ◽  
Two Phase Cooling

It is now widely recognized that the three-dimensional (3D) system integration is a key enabling technology to achieve the performance needs of future microprocessor integrated circuits (ICs). To provide modular thermal management in 3D-stacked ICs, the interlayer microfluidic cooling scheme is adopted and analyzed in this study focusing on a single cooling layer performance. The effects of cooling mode (single-phase versus phase-change) and stack/layer geometry on thermal management performance are quantitatively analyzed, and implications on the through-silicon-via scaling and electrical interconnect congestion are discussed. Also, the thermal and hydraulic performance of several two-phase refrigerants is discussed in comparison with single-phase cooling. The results show that the large internal pressure and the pumping pressure drop are significant limiting factors, along with significant mass flow rate maldistribution due to the presence of hot-spots. Nevertheless, two-phase cooling using R123 and R245ca refrigerants yields superior performance to single-phase cooling for the hot-spot fluxes approaching ∼300 W/cm2. In general, a hybrid cooling scheme with a dedicated approach to the hot-spot thermal management should greatly improve the two-phase cooling system performance and reliability by enabling a cooling-load-matched thermal design and by suppressing the mass flow rate maldistribution within the cooling layer.

Microstructure Simulation and Toughening Mechanism of Ceramic Tool Material

2011 ◽  
Vol 335-336 ◽  
pp. 688-694
Author(s):  
Xiao Hui Zhu ◽  
Chuan Zhen Huang ◽  
Han Lian Liu ◽  
Bin Zou ◽  
Hong Tao Zhu
Keyword(s):  
Mechanical Properties ◽  
Single Phase ◽  
Three Dimensional ◽  
Tool Material ◽  
Ceramic Tool ◽  
Toughening Mechanism ◽  
C Language ◽  
Finite Element Software ◽  
Microstructure Simulation ◽  
Ceramic Tool Material

Based on the microstructure results of Monte Carlo simulation, a three-dimensional grid model is built up, and imported into the finite element software with C++ language to analyze the mechanical properties of ceramic tool material. The stress field and residual stress of single-phase and multiphase ceramics have been analyzed by the computer simulation technology.

Sign in / Sign up

Export Citation Format

Share Document