Evaluation of thermally converted silicotitanate waste forms

1999 ◽  
Vol 556 ◽  
Author(s):  
Y. SU ◽  
M. L. Balmer ◽  
L. Wang ◽  
B. C. Bunker ◽  
M. Nyman ◽  
...  
Keyword(s):  
Thermogravimetric Analysis ◽  
Thermal Conversion ◽  
X Ray Diffraction ◽  
Ion Exchangers ◽  
Waste Streams ◽  
Silicate Phase ◽  
X Ray ◽  
Waste Forms ◽  
Heat Treated ◽  
Crystalline Silicotitanate

AbstractCrystalline silicotitanate ion exchangers are highly selective for separating Cs from Narich waste streams. However, use of these ion exchangers for removal of Cs from radioactive tank waste will result in large volumes of secondary wastes. Thermal conversion of silicotitanates produces a durable waste form with reduced volumes up to 40%. Leach tests (MCC-l and PCT) have shown that Cs leach rates of IE-91 1-Na (heat treated at 900°C for an hour) are extremely low, ranging from 0.1 to lwt% Cs loss in Cs fraction release, or 10-1 to 10-8g/m2day in normalized Cs mass loss. These are several orders of magnitude lower than that of borosilicate glass. In order to understand the interplay between the structure and high Cs durability, X-ray diffraction, 133Cs NMR, and thermogravimetric analysis have been used to identify phase(s) responsible for trapping Cs in these silicotitanates. Results indicate that Cs is likely to be contained in a crystalline silicate phase.

scholarly journals Stable and Metastable Phase Equilibria Involving the Cu6Sn5 Intermetallic

2021 ◽  
Author(s):  
A. Leineweber ◽  
M. Löffler ◽  
S. Martin
Keyword(s):  
Phase Equilibria ◽  
Electron Backscatter Diffraction ◽  
Metastable Phase ◽  
Stable Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Ordered Phases ◽  
Backscatter Diffraction ◽  
Kinetics Of

Abstract Cu6Sn5 intermetallic occurs in the form of differently ordered phases η, η′ and η′′. In solder joints, this intermetallic can undergo changes in composition and the state of order without or while interacting with excess Cu and excess Sn in the system, potentially giving rise to detrimental changes in the mechanical properties of the solder. In order to study such processes in fundamental detail and to get more detailed information about the metastable and stable phase equilibria, model alloys consisting of Cu3Sn + Cu6Sn5 as well as Cu6Sn5 + Sn-rich melt were heat treated. Powder x-ray diffraction and scanning electron microscopy supplemented by electron backscatter diffraction were used to investigate the structural and microstructural changes. It was shown that Sn-poor η can increase its Sn content by Cu3Sn precipitation at grain boundaries or by uptake of Sn from the Sn-rich melt. From the kinetics of the former process at 513 K and the grain size of the η phase, we obtained an interdiffusion coefficient in η of (3 ± 1) × 10−16 m2 s−1. Comparison of this value with literature data implies that this value reflects pure volume (inter)diffusion, while Cu6Sn5 growth at low temperature is typically strongly influenced by grain-boundary diffusion. These investigations also confirm that η′′ forming below a composition-dependent transus temperature gradually enriches in Sn content, confirming that Sn-poor η′′ is metastable against decomposition into Cu3Sn and more Sn-rich η or (at lower temperatures) η′. Graphic Abstract

scholarly journals Valorization of Byproducts of Hemp Multipurpose Crop: Short Non-Aligned Bast Fibers as a Source of Nanocellulose

Molecules ◽  
2021 ◽  
Vol 26 (16) ◽  
pp. 4723
Author(s):  
Sara Dalle Vacche ◽  
Vijayaletchumy Karunakaran ◽  
Alessia Patrucco ◽  
Marina Zoccola ◽  
Loreleï Douard ◽  
...  
Keyword(s):  
Infrared Spectroscopy ◽  
Thermogravimetric Analysis ◽  
Cannabis Sativa ◽  
Crystallinity Index ◽  
Residual Lignin ◽  
Chemical Pretreatment ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bast Fibers ◽  
Seed Maturity

Nanocellulose was extracted from short bast fibers, from hemp (Cannabis sativa L.) plants harvested at seed maturity, non-retted, and mechanically decorticated in a defibering apparatus, giving non-aligned fibers. A chemical pretreatment with NaOH and HCl allowed the removal of most of the non-cellulosic components of the fibers. No bleaching was performed. The chemically pretreated fibers were then refined in a beater and treated with a cellulase enzyme, followed by mechanical defibrillation in an ultrafine friction grinder. The fibers were characterized by microscopy, infrared spectroscopy, thermogravimetric analysis and X-ray diffraction after each step of the process to understand the evolution of their morphology and composition. The obtained nanocellulose suspension was composed of short nanofibrils with widths of 5–12 nm, stacks of nanofibrils with widths of 20–200 nm, and some larger fibers. The crystallinity index was found to increase from 74% for the raw fibers to 80% for the nanocellulose. The nanocellulose retained a yellowish color, indicating the presence of some residual lignin. The properties of the nanopaper prepared with the hemp nanocellulose were similar to those of nanopapers prepared with wood pulp-derived rod-like nanofibrils.

A MOF based on a lead(II) 2-oxido-6-methylpyridine-4-carboxylate network

2020 ◽  
Vol 75 (4) ◽  
pp. 365-369
Author(s):  
Long Tang ◽  
Yu Pei Fu ◽  
Na Cui ◽  
Ji Jiang Wang ◽  
Xiang Yang Hou ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Solid State ◽  
Carboxylic Acid ◽  
Thermogravimetric Analysis ◽  
Metal Organic Framework ◽  
X Ray Diffraction ◽  
X Ray ◽  
Connected Node ◽  
Metal Organic ◽  
Solid State Fluorescence

AbstractA new metal-organic framework, [Pb(hmpcaH)2]n (1), has been hydrothermally synthesized from Pb(OAc)2 · 3H2O and 2-hydroxy-6-methylpyridine-4-carboxylic acid (hmpcaH2; 2), and characterized by IR spectroscopy, elemental and thermogravimetric analysis, and single-crystal X-ray diffraction. In complex 1, each hmpcaH− ligand represents a three-connected node to combine with the hexacoordinated Pb(II) ions, generating a 3D binodal (3,6)-connected ant network. The crystal structure of 2 was determined. The solid-state fluorescence properties of 1 and 2 were investigated.

scholarly journals Features of the hydration process of the modified blended cement for fiber cement panels

2018 ◽  
Vol 170 ◽  
pp. 03030 ◽  
Author(s):  
Rustem Mukhametrakhimov ◽  
Liliya Lukmanova
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Blended Cement ◽  
Physical And Mechanical Properties ◽  
Hydration Process ◽  
Cement Matrix ◽  
X Ray Diffraction ◽  
Structure Form ◽  
Silicate Phase ◽  
X Ray

The paper studies features of the hydration process of the modified blended cement for fiber cement panels (FCP) using differential thermal analysis, X-ray diffraction analysis, electron microscopy and infrared spectroscopy. It is found that deeper hydration process in silicate phase, denser and finer crystalline structure form in fiber cement matrix based on the modified blended cement. Generalization of this result to the case of fiber cement panels makes it possible to achieve formation of a denser and homogeneous structure with increased physical and mechanical properties.

scholarly journals Influence of the Presence of Different Alkali Cations and the Amount of Fe(CN)6 Vacancies on CO2 Adsorption on Copper Hexacyanoferrates

Materials ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3371 ◽  
Author(s):  
Svensson ◽  
Grins ◽  
Eklöf ◽  
Eriksson ◽  
Wardecki ◽  
...  
Keyword(s):  
Thermogravimetric Analysis ◽  
Prussian Blue ◽  
Co2 Adsorption ◽  
X Ray Diffraction ◽  
Alkali Cations ◽  
Prussian Blue Analogue ◽  
X Ray ◽  
Infra Red ◽  
Adsorption Desorption ◽  
Adsorption Capability

The CO2 adsorption on various Prussian blue analogue hexacyanoferrates was evaluated by thermogravimetric analysis. Compositions of prepared phases were verified by energy-dispersive X-ray spectroscopy, infra-red spectroscopy and powder X-ray diffraction. The influence of different alkali cations in the cubic Fm3m structures was investigated for nominal compositions A2/3Cu[Fe(CN)6]2/3 with A = vacant, Li, Na, K, Rb, Cs. The Rb and Cs compounds show the highest CO2 adsorption per unit cell, 3.3 molecules of CO2 at 20 C and 1 bar, while in terms of mmol/g the Na compound exhibits the highest adsorption capability, 3.8 mmol/g at 20 C and 1 bar. The fastest adsorption/desorption is exhibited by the A-cation free compound and the Li compound. The influence of the amount of Fe(CN)6 vacancies were assessed by determining the CO2 adsorption capabilities of Cu[Fe(CN)6]1/2 (Fm3m symmetry, nominally 50% vacancies), KCu[Fe(CN)6]3/4 (Fm3m symmetry, nominally 25% vacancies), and CsCu[Fe(CN)6] (I-4m2 symmetry, nominally 0% vacancies). Higher adsorption was, as expected, shown on compounds with higher vacancy concentrations.

PREPARATION OF ANTIMONY-PLATINUM SURFACE ALLOY ELECTRODE BY ATOM DIFFUSION IN THE SOLID PHASE

2006 ◽  
Vol 20 (25n27) ◽  
pp. 3999-4004
Author(s):  
HIROSHI MATSUI ◽  
KAZUFUMI WATANABE
Keyword(s):  
Diffraction Pattern ◽  
Low Temperatures ◽  
Solid Phase ◽  
Electrochemical Measurement ◽  
X Ray Diffraction ◽  
Platinum Surface ◽  
X Ray ◽  
Atom Diffusion ◽  
Heat Treated ◽  
Titanium Substrates

Antimony-platinum bilayers were prepared on titanium substrates by the two-step electrodeposition in the usual baths, and then surface alloys were formed by the atom diffusion in the solid phase. The simple antimony layer was little influenced by the substrate in both the measurements of X-ray diffraction and the i - E characteristic in a sulfuric acid solution. Regarding the bilayers, the catalytic activity in hydrogen evolution reaction was very sensitive to the presence of platinum, while the hydrogen adsorbability was quite insensitive. An interaction between antimony and platinum was confirmed by the appearance of a new dissolution wave in the electrochemical measurement and the occurrence of a new diffraction in the X-ray diffraction pattern after the heat-treatment of about 400°C. Although the new diffraction disagreed with any of the reported alloys, clear diffraction pattern of PtSb 2 alloy was observed, when the bilayers were heat-treated at about 600°C for one hour. Considering the penetration depth of X-ray, the alloying of antimony and platinum seems to occur also at low temperatures at least at the top surface.

Study of Thermal Behaviour of EPDM/SBR Blends and Carbon Nanocoatings Deposited by Sputtering

2021 ◽  
Vol 875 ◽  
pp. 116-120
Author(s):  
Muhammad Alamgir ◽  
Faizan Ali Ghauri ◽  
Waheed Qamar Khan ◽  
Sajawal Rasheed ◽  
Muhammad Sarfraz Nawaz ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Weight Loss ◽  
Thermogravimetric Analysis ◽  
Thermal Behavior ◽  
Thermal Behaviour ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermal Stability Of

In this study, the effect of SBR concentration (10 Phr, 20 Phr & 30 Phr ) on the thermal behavior of EPDM/SBR blends was studied. Thermogravimetric analysis (TGA) was used to check weight loss of samples as function of temperature by heating upto 600°C. X-ray diffraction (XRD) was performed to determine quality and % crystallinity of the elastomer blends. It was seen that % crystallinity improved with an increase in the content of SBR in EPDM/SBR blends. TGA revealed that the thermal stability of EPDM/SBR blends has improved by 17% than neat EPDM. Carbon nano-coatings produced by sputtering have no beneficial influence on thermal behaviour of elastomers.

Hardening of Selective Laser Melted M2 Steel

2021 ◽  
Author(s):  
Mei Yang ◽  
Yishu Zhang ◽  
Haoxing You ◽  
Richard Smith ◽  
Richard D. Sisson
Keyword(s):  
Heat Treatment ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Steel ◽  
High Hardness ◽  
Steel Part ◽  
X Ray Diffraction ◽  
X Ray ◽  
Heat Treated ◽  
Near Net Shape

Abstract Selective laser melting (SLM) is an additive manufacturing technique that can be used to make the near-net-shape metal parts. M2 is a high-speed steel widely used in cutting tools, which is due to its high hardness of this steel. Conventionally, the hardening heat treatment process, including quenching and tempering, is conducted to achieve the high hardness for M2 wrought parts. It was debated if the hardening is needed for additively manufactured M2 parts. In the present work, the M2 steel part is fabricated by SLM. It is found that the hardness of as-fabricated M2 SLM parts is much lower than the hardened M2 wrought parts. The characterization was conducted including X-ray diffraction (XRD), optical microscopy, Scanning Electron Microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS) to investigate the microstructure evolution of as-fabricated, quenched, and tempered M2 SLM part. The M2 wrought part was heat-treated simultaneously with the SLM part for comparison. It was found the hardness of M2 SLM part after heat treatment is increased and comparable to the wrought part. Both quenched and tempered M2 SLM and wrought parts have the same microstructure, while the size of the carbides in the wrought part is larger than that in the SLM part.

Influence of Organophilization Process Variables in Bentonite Clays from Cubati-PB

2012 ◽  
Vol 727-728 ◽  
pp. 1467-1472
Author(s):  
Carla Dantas da Silva ◽  
Rosa do Carmo de Oliveira Lima ◽  
Julliana Marques Rocha Costa ◽  
Gelmires Araújo Neves ◽  
Heber Carlos Ferreira
Keyword(s):  
Thermogravimetric Analysis ◽  
Bentonite Clay ◽  
Laser Diffraction ◽  
Ionic Surfactants ◽  
Organic Media ◽  
Process Variables ◽  
X Ray Diffraction ◽  
X Ray ◽  
Bentonite Clays ◽  
Sodium Form

This work aims at the development of organoclay from two varieties of bentonite for use in organic media using ionic surfactants, studying the influence of process variables in the organophilization process. We used the following materials: natural bentonite clay from Cubati-PB District, and the ionic quaternary ammonium salt: Praepagen WB® with 45% active matter. The clays were benefited and then turned into sodium form and subsequently into organoclays. The bentonites were characterized by laser diffraction (GA) X-ray fluorescence chemical composition (EDX), thermogravimetric analysis (TGA), thermogravimetry (DTA) and X-ray diffraction (XRD). The organoclays were characterized by (XRD) thermogravimetric analysis (TGA) and thermogravimetry (DTA). The results showed that the clay has potential for application in the organophilization process and that there is influence of process variables.

X-Ray Diffraction Analysis on Crystallite Development of Nanostructured Aluminium

2006 ◽  
Vol 118 ◽  
pp. 53-58
Author(s):  
Elisabeth Meijer ◽  
Nicholas Armstrong ◽  
Wing Yiu Yeung
Keyword(s):  
Crystallite Size ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Equal Channel Angular Extrusion ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
Integral Breadth ◽  
X Ray ◽  
Heat Treated ◽  
Diffraction Peaks

This study is to investigate the crystallite development in nanostructured aluminium using x-ray line broadening analysis. Nanostructured aluminium was produced by equal channel angular extrusion at room temperature to a total deformation strain of ~17. Samples of the extruded metal were then heat treated at temperatures up to 300oC. High order diffraction peaks were obtained using Mo radiation and the integral breadth was determined. It was found that as the annealing temperature increased, the integral breadth of the peak reflections decreased. By establishing the modified Williamson-Hall plots (integral breadth vs contract factor) after instrumental correction, it was determined that the crystallite size of the metal was maintained ~80 nm at 100oC. As the annealing temperature increased to 200oC, the crystallite size increased to ~118 nm. With increasing annealing temperature, the hardness of the metal decreased from ~60 HV to ~45 HV.

Sign in / Sign up

Export Citation Format

Share Document