The Design of a Monitoring Program for Iron Alloys on Underwater Historic Shipwrecks in Fathom Five National Marine Park, Ontario, Canada

1996 ◽  
Vol 462 ◽  
Author(s):  
John Stewart ◽  
Lome D. Murdock ◽  
Nancy Binnie
Keyword(s):  
Monitoring Program ◽  
Iron Alloys ◽  
Visual Observation ◽  
Photographic Recording ◽  
Ph Measurements ◽  
Surface Ph ◽  
X Ray ◽  
Marine Park ◽  
Predominant Form

ABSTRACTIn order to design a scheme to monitor the state of preservation of iron alloys that are found on historic shipwrecks sunk in fresh water, it was first necessary to identify the predominant form of corrosion found on the wrecks. This was done by visual observation, in situ surface pH measurements, and X-ray powder diffraction of the corrosion layers. Once the form of corrosion was identified as pitting corrosion, a monitoring scheme based on photographic recording of the rust-red tubercles was designed. This scheme is simple and nondestructive, both necessary characteristics for the monitoring of submerged historic resources.

Smart: Scientific Monitoring of Advanced Response Technologies

1999 ◽  
Vol 1999 (1) ◽  
pp. 1265-1267 ◽  
Author(s):  
Nir Barnea ◽  
Roger Laferriere
Keyword(s):  
Real Time ◽  
Monitoring Program ◽  
Visual Observation ◽  
Data Logging ◽  
Tier Ii ◽  
Oil Spill Response ◽  
Aerial Platforms ◽  
Unified Command ◽  
Trained Observers

ABSTRACT SMART (Scientific Monitoring of Advanced Response Technologies) is a new monitoring program designed to provide the Unified Command with real-time field data when in situ burning and dispersants are used during oil spill response. For dispersant monitoring, SMART recommends a three-tiered approach. Tier I has visual observation by trained observers from vessels or from aerial platforms. Tier II combines visual observations with water-column sampling using a fluorometer at a single depth. Tier III expands the fluorometry monitoring to several water depths, and uses a water-quality lab. Water samples for later analysis and correlation of fluorometry readings are taken both in Tier II and Tier III. For in situ burning, SMART recommends deploying three or more monitoring teams, each equipped with a real-time particulate monitor with data-logging capability. The teams deploy downwind of the burn at sensitive locations, and report particulate concentration trends to the Unified Command.

In-situ X-ray and visual observation of foam morphology and behavior at the batch-melt interface during melting of simulated waste glass

2021 ◽  
Author(s):  
José Marcial ◽  
Steven Luksic ◽  
Jaroslav Kloužek ◽  
Miroslava Vernerová ◽  
Derek Cutforth ◽  
...  
Keyword(s):  
Visual Observation ◽  
Waste Glass ◽  
X Ray ◽  
Foam Morphology ◽  
Simulated Waste ◽  
And Behavior

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

In Situ X-Ray Absorption Studies of the Electrochemical Reduction of Hydroxocobalamin

1997 ◽  
Vol 7 (C2) ◽  
pp. C2-619-C2-620 ◽  
Author(s):  
M. Giorgett ◽  
I. Ascone ◽  
M. Berrettoni ◽  
S. Zamponi ◽  
R. Marassi
Keyword(s):  
Electrochemical Reduction ◽  
X Ray ◽  
Absorption Studies ◽  
X Ray Absorption

A Revised O2 Reduction Model in Li-O2 Batteries as Revealed by in Situ Small Angle X-Ray Scattering

2019 ◽  
Author(s):  
Christian Prehal ◽  
Aleksej Samojlov ◽  
Manfred Nachtnebel ◽  
Manfred Kriechbaum ◽  
Heinz Amenitsch ◽  
...  
Keyword(s):  
Small Angle ◽  
Wide Angle ◽  
Reduction Mechanism ◽  
Reduction Model ◽  
X Ray ◽  
X Ray Scattering ◽  
O2 Reduction ◽  
Ray Scattering

<b>Here we use in situ small and wide angle X-ray scattering to elucidate unexpected mechanistic insights of the O2 reduction mechanism in Li-O2 batteries.<br></b>

Single Crystal Growth of High-Pressure Phases of Ice and Salt Hydrate Far Below the Original Melting Point by Mixing Alcohol: Crystal Structure Determination of Magnesium Chloride Heptahydrate

2020 ◽  
Author(s):  
Keishiro Yamashita ◽  
Kazuki Komatsu ◽  
Hiroyuki Kagi
Keyword(s):  
Crystal Structure ◽  
High Pressure ◽  
Crystal Growth ◽  
Single Crystal ◽  
Room Temperature ◽  
Growth Technique ◽  
Salt Hydrate ◽  
X Ray

An crystal-growth technique for single crystal x-ray structure analysis of high-pressure forms of hydrogen-bonded crystals is proposed. We used alcohol mixture (methanol: ethanol = 4:1 in volumetric ratio), which is a widely used pressure transmitting medium, inhibiting the nucleation and growth of unwanted crystals. In this paper, two kinds of single crystals which have not been obtained using a conventional experimental technique were obtained using this technique: ice VI at 1.99 GPa and MgCl<sub>2</sub>·7H<sub>2</sub>O at 2.50 GPa at room temperature. Here we first report the crystal structure of MgCl2·7H2O. This technique simultaneously meets the requirement of hydrostaticity for high-pressure experiments and has feasibility for further in-situ measurements.

Monitoring Polymer-Assisted Mechanochemical Cocrystallisation Through in Situ X-Ray Powder Diffraction

2020 ◽  
Author(s):  
Luzia S. Germann ◽  
Sebastian T. Emmerling ◽  
Manuel Wilke ◽  
Robert E. Dinnebier ◽  
Mariarosa Moneghini ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Powder Diffraction ◽  
Reaction Rate ◽  
Polymer Additives ◽  
Time Resolved ◽  
X Ray

Time-resolved mechanochemical cocrystallisation studies have so-far focused solely on neat and liquid-assisted grinding. Here, we report the monitoring of polymer-assisted grinding reactions using <i>in situ</i> X-ray powder diffraction, revealing that reaction rate is almost double compared to neat grinding and independent of the molecular weight and amount of used polymer additives.<br>

Atomic Layer Deposition of LiF and Lithium Ion Conducting (AlF3)(LiF)x Alloys Using Trimethylaluminum, Lithium Hexamethyldisilazide and Hydrogen Fluoride

2017 ◽  
Author(s):  
Younghee Lee ◽  
Daniela M. Piper ◽  
Andrew S. Cavanagh ◽  
Matthias J. Young ◽  
Se-Hee Lee ◽  
...  
Keyword(s):  
Lithium Ion ◽  
Atomic Layer ◽  
Mass Gain ◽  
Alloy Film ◽  
Ex Situ ◽  
X Ray ◽  
Layer Deposition ◽  
Ion Conducting ◽  
Good Agreement

<div>Atomic layer deposition (ALD) of LiF and lithium ion conducting (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloys was developed using trimethylaluminum, lithium hexamethyldisilazide (LiHMDS) and hydrogen fluoride derived from HF-pyridine solution. ALD of LiF was studied using in situ quartz crystal microbalance (QCM) and in situ quadrupole mass spectrometer (QMS) at reaction temperatures between 125°C and 250°C. A mass gain per cycle of 12 ng/(cm<sup>2</sup> cycle) was obtained from QCM measurements at 150°C and decreased at higher temperatures. QMS detected FSi(CH<sub>3</sub>)<sub>3</sub> as a reaction byproduct instead of HMDS at 150°C. LiF ALD showed self-limiting behavior. Ex situ measurements using X-ray reflectivity (XRR) and spectroscopic ellipsometry (SE) showed a growth rate of 0.5-0.6 Å/cycle, in good agreement with the in situ QCM measurements.</div><div>ALD of lithium ion conducting (AlF3)(LiF)x alloys was also demonstrated using in situ QCM and in situ QMS at reaction temperatures at 150°C A mass gain per sequence of 22 ng/(cm<sup>2</sup> cycle) was obtained from QCM measurements at 150°C. Ex situ measurements using XRR and SE showed a linear growth rate of 0.9 Å/sequence, in good agreement with the in situ QCM measurements. Stoichiometry between AlF<sub>3</sub> and LiF by QCM experiment was calculated to 1:2.8. XPS showed LiF film consist of lithium and fluorine. XPS also showed (AlF<sub>3</sub>)(LiF)x alloy consists of aluminum, lithium and fluorine. Carbon, oxygen, and nitrogen impurities were both below the detection limit of XPS. Grazing incidence X-ray diffraction (GIXRD) observed that LiF and (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film have crystalline structures. Inductively coupled plasma mass spectrometry (ICP-MS) and ionic chromatography revealed atomic ratio of Li:F=1:1.1 and Al:Li:F=1:2.7: 5.4 for (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film. These atomic ratios were consistent with the calculation from QCM experiments. Finally, lithium ion conductivity (AlF<sub>3</sub>)(LiF)<sub>x</sub> alloy film was measured as σ = 7.5 × 10<sup>-6</sup> S/cm.</div>

Sign in / Sign up

Export Citation Format

Share Document