Effect of Glass Composition on Mechanical Properties of Interfaces Between Alumina and Silicate Glass

1996 ◽  
Vol 458 ◽  
Author(s):  
Andrey V. Zagrebelny ◽  
Erica T. Lilleodden ◽  
C. Barry Carter
Keyword(s):  
Mechanical Properties ◽  
Single Crystal ◽  
Silicate Glass ◽  
Glass Composition ◽  
Depth Sensing ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Imaging ◽  
Force Displacement

ABSTRACTInterfaces between glass and crystalline grains have been examined using a thin-film geometry which allows the use of newly developed experimental methods for micromechanical testing of interfaces. In this approach, continuous films of thicknesses ranging 100–200 nm of anorthite (CaAl2Si2O8), celsian (BaAl2Si2O8), and monticellite (CaMgSiO4) are deposited onto single-crystal Al2O3 (α-structure) surfaces of different crystallographic orientations by pulsed-laser deposition (PLD).Mechanical properties such as hardness, stiffness, and reduced Young's modulus were probed with a newly developed high-resolution depth-sensing indentation instrument. Emphasis has been placed on examining how changes in the glass composition will affect the mechanical properties of the single-crystal Al2O3/silicate-glass interfaces. The indentation data obtained from these experiments correlate directly to the morphology of the deformed regions imaged with atomic force microscopy (AFM). Nanomechanical tests combined with AFM imaging of the deformed regions allow force-displacement measurements and in-situ imaging of the same regions of the specimen before and immediately after indentation. This new technique eliminates the uncertainty of locating the indenter after unloading.

Alumina-Silicate Glass Interfacial Properties Probed by Micromechanical Testing Techniques

1995 ◽  
Vol 401 ◽  
Author(s):  
Andrey V. Zagrebelnya ◽  
John C. Nelson ◽  
Erica T. Lilleodden ◽  
Sundar Ramamurthy ◽  
C. Barry Carter
Keyword(s):  
Force Microscopy ◽  
Operating Modes ◽  
Deformation Structures ◽  
Atomic Force ◽  
Afm Imaging ◽  
Before And After ◽  
Calcium Aluminosilicate ◽  
Testing Techniques ◽  
Force Displacement

AbstractMicromechanical properties of the interfaces between alumina and calcium-aluminosilicate (CAS) glasses were tested using various micro/nanoindentation techniques. The interfaces were produced by depositing continuous films of anorhtite (CaAl2Si2O8) onto single-crstal α-Al2O3 of two crystallographic orientations by pulsed-laser deposition (PLD).The mechanical behavior of the interfaces was examined using two different depthsensing indentation instruments. Three types of tests, namely indentation, microscratch, and in-situ indentation combined with atomic force microscopy (AFM) imaging were conducted using different operating modes. The deformation behavior observed for the indentations and microscratches has been correlated with irregularities observed in the load-displacement curves. In the first two cases, scanning electron microscopy (SEM) has been used to characterize the deformation structures associated with the deformed regions. The in-situ experiments allow force-displacement measurements and AFM imaging immediately before and after indentation. The preindent and postindent morphology of the surface could then be characterized.

Micromechanical Properties of Silicate Glass Films on Sapphire Substrates

1997 ◽  
Vol 505 ◽  
Author(s):  
Andrey V. Zagrebelny ◽  
C. Barry Carter
Keyword(s):  
Mechanical Properties ◽  
Silicate Glass ◽  
Thin Layers ◽  
Depth Sensing ◽  
Crystalline Materials ◽  
Sapphire Substrates ◽  
Nanomechanical Testing ◽  
Force Displacement ◽  
Glass Films

ABSTRACTThe deformation of thin layers of glass on crystalline materials has been examined using newly developed experimental methods for nanomechanical testing. Continuous films of anorthite (CaAl2Si2O8), celsian (BaAl2Si2O8), and monticellite (CaMgSiO4) were deposited onto A12O3 surfaces by pulsed-laser deposition (PLD). Mechanical properties such as Young's modulus and hardness were probed with a high-resolution depth-sensing indentation instrument. Nanomechanical testing, combined with AFM in-situ imaging of the deformed regions, allowed force-displacement measurements and imaging of the same regions of the specimen before and immediately after indentation. Emphasis has been placed on examining how changes in the glass composition, residual stress introduced into the films, effect of film's heat-treatment, and the effect of substrate crystallographic orientation will affect the mechanical properties of silicate-glass films.

scholarly journals Novel Sulfonated Ethylene/1-Octene Copolymer Ionomer Nanocomposite: Synthesis and Properties

2013 ◽  
Vol 28 ◽  
pp. 59-66
Author(s):  
Sharmila Pradhan ◽  
Stefanie Scholtissek ◽  
Ralf Lach ◽  
Werner Lebek ◽  
Wolfgang Grellmann ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Layered Silicate ◽  
Chemical Society ◽  
Depth Sensing ◽  
Force Microscopy ◽  
Atomic Force ◽  
Solution Cast ◽  
Scanning Electron ◽  
Cast Technique

The nanocomposites based on sulfonated ethylene/1-octene copolymer (sEOC) and organophilic modified layered silicate were synthesized. The morphology of the ionomeric product was studied with the help of Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Fourier Transform Infrared (FTIR) spectroscopy and microhardness measurements. It was shown that via the solution cast technique, the nanocomposite with uniformly distributed filer morphology can be conveniently prepared. The significant enhancement of the mechanical properties due to ionomerization was attested with the help of depth sensing microhardness measurements. It was found that the hardness of ionomer nanocomposite comprising 5 wt.-% layered silicate is approximately four fold of the neat elastomer. DOI: http://dx.doi.org/10.3126/jncs.v28i0.8060 Journal of Nepal Chemical Society Vol.28, 2011 Page : 59-66 Uploaded date: May 7, 2013

scholarly journals In Situ AFM Imaging of Adsorption Kinetics of DPPG Liposomes: A Quantitative Analysis of Surface Roughness

2019 ◽  
Vol 25 (3) ◽  
pp. 798-809
Author(s):  
Andreia A. Duarte ◽  
Joaquim T. Marquês ◽  
Francisco Brasil ◽  
Ana S. Viana ◽  
Pedro Tavares ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Hydrodynamic Diameter ◽  
Supported Lipid Bilayer ◽  
Force Microscopy ◽  
Atomic Force ◽  
Power Spectral ◽  
Afm Imaging ◽  
Density Analysis ◽  
Power Spectral Density Analysis

AbstractThe adsorption of intact liposomes on surfaces is of great importance for the development of sensors and drug delivery systems and, also, strongly dependent on the surface roughness where the liposomes are adsorbed. In this paper, we analyzed, by using atomic force microscopy in liquid, the evolution of the morphology of gold surfaces and of poly(allylamine hydrochloride) (PAH) surfaces with different roughness during the adsorption of liposomes prepared with the synthetic phospholipid 1,2-dipalmitoyl-sn-glycero-3-[phospho-rac-(1-glycerol)]. Our results reveal the following. On smooth surfaces of Au only and Au with PAH, the liposomes open and deploy on the substrate, creating a supported-lipid bilayer, with the opening process being faster on the Au/PAH surface. On rough substrates of Au coated with polyelectrolyte multilayers, the liposomes were adsorbed intact on the surface. This was corroborated by power spectral density analysis that demonstrates the presence of superstructures with an average lateral size of 43 and 87 nm, in accordance with two and four times the mean liposome hydrodynamic diameter of about 21 nm. In addition, this work presents an adequate and effective methodology for analysis of adsorption phenomena of liposomes on rough surfaces.

In-situ and ex-situ AFM imaging of μN load indents on silicate glass/alumina interfaces

1996 ◽  
Vol 54 ◽  
pp. 660-661
Author(s):  
A. V. Zagrebelny ◽  
E. T. Lilleodden ◽  
J. C. Nelson ◽  
S. Ramamurthy ◽  
C. B. Carter
Keyword(s):  
Single Crystal ◽  
Silicate Glass ◽  
Small Volume ◽  
Ex Situ ◽  
Surface Roughening ◽  
Mechanistic Approach ◽  
Afm Imaging ◽  
Indentation Analysis ◽  
Single Crystal Sapphire

Contact which only involves a small volume of material is becoming increasingly important to many industries including micromachines, microelectronics, and magnetic recording. The ability to characterize surface roughening on the micro- and nanoscopic scale is invaluable in understanding microplasticity due to indentation, scratches, wear, fatigue and epitactic mismatch. It has been demonstrated that AFM studies are appropriate for developing a mechanistic approach to μN load indentation analysis since they allow deformation volumes and residual depths to be measured and characterized directly and unambiguously.In the present study, interfaces between silicate glass and single-crystal α-Al2O3 have been studied using AFM and nanoindentation. The interfaces between the glass and the crystalline grains were prepared by growing films of anorthite (CaAl2Si2O8) composition with thickness ranging 100-200 nm on single-crystal sapphire substrates of {1120} (A-plane) and {1102} (R-plane) crystallographic orientations by pulsed-laser deposition (PLD). Some specimens were subjected to heat treatments in a conventional box furnace causing films to dewet the substrates. Fig. 1 shows schematically the morphology of the dewetted film which has resulted in the formation of distinctive islands, 0.5-2 μm in size. Both types of specimens were tested with two different micro/nanomechanical testers.

Experimental investigations into the mechanical properties of the collagen fibril-noncollagenous protein (NCP) interface in antler bone

2010 ◽  
Vol 1274 ◽  
Author(s):  
Fei Hang ◽  
Asa H Barber
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Collagen Fibrils ◽  
Experimental Investigations ◽  
Shear Stresses ◽  
Structural Hierarchy ◽  
Force Microscopy ◽  
Atomic Force ◽  
The Individual

AbstractAntler is an extraordinary bone tissue that displays significant overall toughness when compared to other bone materials. The origin of this toughness is due to the complex interaction between the nanoscale constituents as well as structural hierarchy in the antler material. Of particular interest is the mechanical performance of the interface between the collagen fibrils and considerably smaller volume of non-collagenous protein (NCP) between these fibrils. This paper directly examines the mechanical properties of isolated volumes of antler using combined in situ atomic force microscopy (AFM)-scanning electron microscopy (SEM) experiments. The antler material at the nanoscale is approximated to a fiber reinforced composite, with composite theory used to evaluate the interfacial shear stresses generated between the individual collagen fibrils and NCP during mechanical loading.

Dielectric and Electromechanical Behaviour of Relaxor [(1−x)Pb(Mg1/3Nb2/3)O3 -xPbTiO3] Thin Films

2001 ◽  
Vol 688 ◽  
Author(s):  
N.J. Donnelly ◽  
G. Catalan ◽  
C. Morros ◽  
R.M. Bowman ◽  
J.M. Gregg
Keyword(s):  
Thin Films ◽  
Single Crystal ◽  
Plane Strain ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Bulk Ceramic ◽  
Atomic Force ◽  
Out Of Plane ◽  
Order Of Magnitude

AbstractThin film capacitor structures of Au / (1−x)Pb(Mg1/3Nb2/3)O3 - xPbTiO3 /(La1/2Sr1/2)CoO3 were fabricated by pulsed laser deposition on single crystal {001} MgO substrates. Films were found to be perovskite dominated and highly {001} oriented. Dielectrically, films displayed relaxorlike features, though maximum permittivity was low compared to single crystal or bulk ceramic (∼1400 at peak @1kHz, for x=0.07, 0.1 & 0.2). A field induced piezoelectric coefficient d33 was measured by piezoresponse atomic force microscopy for specific compositions x =0, × =0.07, and x =0.1 and found to be disappointingly low - indicating poor electric field induced strain. Despite this macroscopic electrostrictive coefficients Q33 were found to be (3.6 ± 0.6) ×10−2C−2m4, (2.6 ± 0.2) ×10−2C−2m4, and (0.9 ± 0.3) ×10−2C−2m4 respectively. Crystallographic electrostrictive coefficients were determined by in-situ x-ray diffraction and found to be (4.9 ± 0.2) ×10−2C−2m4 for PMN-(0.07)PT and (1.9 ± 0.1) ×10−2C−2m4 for PMN-(0.1)PT. Considering that all these Q33 values are of the same order of magnitude as found in single crystal experiments (2.5 – 3.8 ×10−2C−2m4), it is suggested that low out-of-plane strain is entirely a result of reduced polarisability rather than reduced electrostrictive coefficients in thin films relative to bulk ceramic or single crystal. An estimate was also made of the Q13 electrostrictive coefficient for PMN and PMN-(0.07)PT by measuring permittivity as a function of applied in-plane strain. The values obtained were -1.31 ×10−2C−2m4 and -0.46 ×10−2C−2m4 respectively.

Measuring size-dependent mechanical properties of electrospun polystyrene fibers using in-situ AFM-SEM

2012 ◽  
Vol 1424 ◽  
Author(s):  
Russell J. Bailey ◽  
Beatriz Cortes-Ballesteros ◽  
Hao Zhang ◽  
Congwei Wang ◽  
Asa H. Barber
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Fiber Diameter ◽  
Electrospun Fibers ◽  
Force Microscopy ◽  
Size Dependent ◽  
Atomic Force ◽  
Scanning Electron

ABSTRACTThe mechanical properties of individual electrospun polystyrene fibers with sub-micron diameters were measured using a combination of atomic force microscopy (AFM) and scanning electron microscopy (SEM). The strain to failure of the electrospun fibers was observed to increase as the fiber diameter decreased. This size dependent mechanical behavior in individual electrospun polystyrene fibers indicates a suppression of localized failure and a shift away from crazing that is dominant in bulk samples.

Sign in / Sign up

Export Citation Format

Share Document