scholarly journals Nonlinear Model Reduction Strategies for Rapid Thermal Processing Systems

1996 ◽  
Vol 429 ◽  
Author(s):  
Suman Banerjee ◽  
J. Vernon Cole ◽  
Klavs F. Jensen ◽  
A. Emami-Naeni
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Thermal Processing ◽  
Large Scale ◽  
Nonlinear Models ◽  
Rapid Thermal Processing ◽  
Element Model ◽  
Physically Based ◽  
The Finite Element Model ◽  
Low Order

AbstractThis paper presents a systematic way of developing low order nonlinear models from physically- based, large scale finite element models of rapid thermal processing (RTP) systems. The low order model is extracted from transient results of the finite element model using the proper orthogonal decomposition (POD) method. Eigenfunctions obtained from the POD method are used as basis functions in spectral Galerkin expansions of partial differential equations solved by the finite element model to generate the reduced models. Simulation results demonstrate good agreement with steady state and transient data generated from the finite element model.

Finite Element Analysis on Large-Scale Electrical Dust Precipitator Steel Structures

2013 ◽  
Vol 753-755 ◽  
pp. 1196-1200
Author(s):  
Lu Yu Huang ◽  
Yang Gao ◽  
Xia Cao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Optimization Design ◽  
Large Scale ◽  
Steel Structures ◽  
Element Model ◽  
Element Analysis ◽  
Dust Precipitator ◽  
The Finite Element Model

Based on the construction features of the steel structures of a type of electrical dust precipitator, a finite element model is established with large-scale finite element analysis software ANSYS, and the structure stress and displacement of the model under all sorts of loads are analyzed with the frontal solution method. The results indicate that analysis is relatively accurate, the finite element model and the analysis method is appropriate. The result can be further used for optimization design of the electrical precipitator steel structures.

scholarly journals Methods for calculating the reinforcement of concrete slabs with carbon composite materials based on the finite element model

2018 ◽  
Vol 251 ◽  
pp. 04061 ◽  
Author(s):  
Valeriy Telichenko ◽  
Vladimir Rimshin ◽  
Ekaterina Kuzina
Keyword(s):  
Finite Element ◽  
Composite Materials ◽  
Finite Element Model ◽  
Large Scale ◽  
Element Model ◽  
Carbon Composite ◽  
Before And After ◽  
Carbon Composite Materials ◽  
Design Values ◽  
The Finite Element Model

In this article, a method is proposed for calculating the reinforcement of concrete ceiling slabs with carbon composite materials based on the finite element model in the computer program SCAD Office PC. This method allows the most complete and accurate representation to be obtained of the structure stress-strain state before and after reinforcement with composite materials. Therefore, it allows high-quality designing and reduces the cost conducting calculations and tests on a large scale. The design values are taken from the initial data, and include conclusions based on the results of analysis of the technical state of the structures and drawings from the calculation section of the CS (reinforced concrete structures).

scholarly journals Investigation on the Performance of Partial Penetration Welds in Multicell Concrete Filled Steel Tubes

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7543
Author(s):  
Lian-Jin Bao ◽  
Fei-Fei Sun ◽  
Osama Mughrabi ◽  
Liu-Lian Li ◽  
Guo-Qiang Li
Keyword(s):  
Finite Element ◽  
Regression Analysis ◽  
Finite Element Model ◽  
Large Scale ◽  
Element Model ◽  
Experimental Program ◽  
Steel Tubes ◽  
Partial Penetration ◽  
Concrete Filled Steel Tubes ◽  
The Finite Element Model

This paper presents an experimental and analytical investigation on the performance of partial penetration welds used to adjoin steel plates in irregular shaped multicell concrete filled steel tubes. The experimental program of this study is designed based on an actual implementation of such members as mega columns in a super high rise building in China. A total of six specimens are designed with different plate arrangements for the purpose of testing the performance of the partial penetration welds at different locations of the specimen. The designed specimens are tested under different load procedures and directions; this is achieved by placing them in vertical and slantwise manners between two loading plates which impose monotonic and cyclic actions. The failure conditions of each of the tested specimens are presented and discussed in detail and are based on the conclusions drawn from the experimental observations; the partial penetration weld at the corner of the tested specimens is found to be the most vulnerable. To facilitate large scale analysis, a finite element model constructed by the finite element analysis program ABAQUS is verified against experimental results. The evaluation of the stress at the partial penetration welded corner is carried out following an empirical procedure, which is adopted due to the complexity of the problem domain. The adopted procedure consists of two steps: the first one is to initially evaluate the stress based on an existing method in the literature, and the second one is to fit the results of the initial evaluation with the finite element model results based on parametric and regression analysis. After performing regression analysis, a formula to predict the weld stress is concluded, and the results of the proposed equation are found to be satisfactory when compared with the finite element model results.

scholarly journals Sensitivity Analysis of the Influence of Structural Parameters on Dynamic Behaviour of Highly Redundant Cable-Stayed Bridges

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
B. Asgari ◽  
S. A. Osman ◽  
A. Adnan
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Structural Parameters ◽  
Element Model ◽  
Structural Behavior ◽  
Model Tuning ◽  
The Finite Element Model ◽  
Cable Stayed Bridges

The model tuning through sensitivity analysis is a prominent procedure to assess the structural behavior and dynamic characteristics of cable-stayed bridges. Most of the previous sensitivity-based model tuning methods are automatic iterative processes; however, the results of recent studies show that the most reasonable results are achievable by applying the manual methods to update the analytical model of cable-stayed bridges. This paper presents a model updating algorithm for highly redundant cable-stayed bridges that can be used as an iterative manual procedure. The updating parameters are selected through the sensitivity analysis which helps to better understand the structural behavior of the bridge. The finite element model of Tatara Bridge is considered for the numerical studies. The results of the simulations indicate the efficiency and applicability of the presented manual tuning method for updating the finite element model of cable-stayed bridges. The new aspects regarding effective material and structural parameters and model tuning procedure presented in this paper will be useful for analyzing and model updating of cable-stayed bridges.

Biodynamics of Human Thorax With Body Armors Subject to Bullet Impact

2001 ◽  
Author(s):  
Y. W. Kwon ◽  
J. A. Lobuono
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Body Armor ◽  
Projectile Impact ◽  
Human Thorax ◽  
Trachea And Bronchi ◽  
Armor System ◽  
The Finite Element Model

Abstract The objective of this study is to develop a finite element model of the human thorax with a protective body armor system so that the model can adequately determine the thorax’s biodynamical response from a projectile impact. The finite element model of the human thorax consists of the thoracic skeleton, heart, lungs, major arteries, major veins, trachea, and bronchi. The finite element model of the human thorax is validated by comparing the model’s results to experimental data obtained from cadavers wearing a protective body armor system undergoing a projectile impact.

Dynamic Analysis of a Turbocharger Centrifugal Compressor Impeller

1991 ◽  
Author(s):  
V. Ramamurti ◽  
D. A. Subramani ◽  
K. Sridhara
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Centrifugal Compressor ◽  
Element Model ◽  
Simplified Model ◽  
Cyclic Symmetry ◽  
Compressor Impeller ◽  
Cyclic Symmetric ◽  
The Finite Element Model

Abstract Stress analysis and determination of eigen pairs of a typical turbocharger compressor impeller have been carried out using the concept of cyclic symmetry. A simplified model treating the blade and the hub as isolated elements has also been attempted. The limitations of the simplified model have been brought out. The results of the finite element model using the cyclic symmetric approach have been discussed.

Analysis of Effective Pre-Stress of Continuous Rigid Frame Bridge in Service Based on Inversion Theory

2013 ◽  
Vol 671-674 ◽  
pp. 1012-1015
Author(s):  
Zhao Ning Zhang ◽  
Ke Xing Li
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Inversion Method ◽  
Vertical Deflection ◽  
Continuous Rigid Frame Bridge ◽  
Rigid Frame ◽  
Inversion Theory ◽  
Rigid Frame Bridge ◽  
The Finite Element Model

Due to the environment, climate, loads and other factors, the pre-stress applied to the beam is not a constant. It is important for engineers to track the state of the pre-stress in order to ensure security of the bridge in service. To solve the problem mentioned above, the paper puts forward a new way to analyze the effective pre-stress using the displacement inversion method based on the inversion theory according to the measured vertical deflection of the bridge in service at different time. The method is a feasible way to predict the effective pre-stress of the bridge in service. Lastly, taking the pre-stressed concrete continuous rigid frame bridge for example, the effective pre-stress is analyzed by establishing the finite element model.

scholarly journals Physical Principles of a Piezo Accelerometer Sensitive to a Nearly Constant Signal

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3258 ◽  
Author(s):  
Valery Gupalov ◽  
Alexander Kukaev ◽  
Sergey Shevchenko ◽  
Egor Shalymov ◽  
Vladimir Venediktov
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Frequency Band ◽  
Linear Acceleration ◽  
High Sensitivity ◽  
Element Model ◽  
Wide Frequency Band ◽  
Piezoelectric Accelerometer ◽  
The Finite Element Model ◽  
Physical Principles

The paper considers the construction of a piezoelectric accelerometer capable of measuring constant linear acceleration. A number of designs are proposed that make it possible to achieve high sensitivity with small dimensions and a wide frequency band (from 10−5 Hz). The finite element model of the proposed design was investigated, and its output characteristic and scale factor (36 mV/g) were obtained.

Analysis on sealing performance of VL seals based on mixed lubrication theory

2019 ◽  
Vol 71 (1) ◽  
pp. 54-60 ◽  
Author(s):  
Shixian Xu ◽  
Zhengtao Su ◽  
Jian Wu
Keyword(s):  
Finite Element ◽  
Film Thickness ◽  
Finite Element Model ◽  
Friction Factor ◽  
Contact Pressure ◽  
Element Model ◽  
Mixed Lubrication ◽  
Content Type ◽  
Deformation Mechanics ◽  
The Finite Element Model

Purpose This paper aims to research the influence of pressure, friction factors, roughness and actuating speed to the mixed lubrication models of outstroke and instroke. Design/methodology/approach Mixed lubrication model is solved by finite volume method, which consists of coupled fluid mechanics, deformation mechanics and contact mechanics analyses. The influence of friction factor on the finite element model is also considered. Then, contact pressure, film thickness, friction and leakage have been studied. Findings It was found that the amount of leakage is sensitive to the film thickness. The larger the film thickness is, the greater the influence received from the friction factor, however, the effect of oil film on the friction is negligible. The friction is determined mainly by the contact pressure. The trend of friction and leakage influenced by actuating velocity and roughness is also obtained. Originality/value The influence of friction factor on the finite element model is considered. This can make the calculation more accurate.

Sign in / Sign up

Export Citation Format

Share Document