Magnetic Properties of Nanoscale Iron Particles Photodeposited in Glass

1995 ◽  
Vol 405 ◽  
Author(s):  
D. Sunil ◽  
H. D. Gafney ◽  
C. Tsang ◽  
M. H. Rafailovich ◽  
J. Sokolov ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Magnetic Properties ◽  
Magnetization Curve ◽  
Room Temperature ◽  
Iron Particles ◽  
Vycor Glass ◽  
Porous Vycor Glass ◽  
Transmission Electron ◽  
Nanoscale Iron Particles

AbstractTransmission Electron Microscopy(TEM) and magnetization measurements were used to study the correlation between size of the iron particles precipitated in glass and their magnetic properties. The iron particles les s than 40 Å in diameter photodeposited in porous Vycor glass(PVG) show superparamagnetic behavior at room temperature. As the size of the particles increases and reaches about 100 Å in diameter, the magnetization curve shows minor hysteresis with a very large coercivity.

Preparation, Characterization and Magnetic Property of MFe2O4 (m=Mn, Zn, Ni, Co) Nanoparticles

2013 ◽  
Vol 842 ◽  
pp. 35-38 ◽  
Author(s):  
Li Xia Yang ◽  
Sha Li ◽  
Jing Zhang ◽  
Zhou Chen ◽  
Shi Cheng Xu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Magnetic Properties ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Basic Source ◽  
Co Nanoparticles ◽  
Zn Nanoparticles

MFe2O4 (M=Mn, Co, Ni, Zn) Nanoparticles with diameters from 5nm to 30nm have been prepared through a hydrothermal method. In this system, ethanolamine was used as a basic source instead of NaOH. The as-prepared ferrites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). In addition, the magnetic properties of the obtained ferrites have been studied at room temperature, showing that the magentic properties of ferrites closely depended on the chemical composition of M2+.

Scanning and Transmission Electron Microscopy of Human Red Blood Cells

1969 ◽  
Vol 27 ◽  
pp. 44-45
Author(s):  
A.J. Tousimis ◽  
T.R. Padden
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Blood Cells ◽  
Room Temperature ◽  
Type Specimen ◽  
New Combination ◽  
Human Red Blood Cells ◽  
Transmission Electron ◽  
Microscope Slides ◽  
Scanning Electron

The size, shape and surface morphology of human erythrocytes (RBC) were examined by scanning electron microscopy (SEM), of the fixed material directly and by transmission electron microscopy (TEM) of surface replicas to compare the relative merits of these two observational procedures for this type specimen.A sample of human blood was fixed in glutaraldehyde and washed in distilled water by centrifugation. The washed RBC's were spread on freshly cleaved mica and on aluminum coated microscope slides and then air dried at room temperature. The SEM specimens were rotary coated with 150Å of 60:40- gold:palladium alloy in a vacuum evaporator using a new combination spinning and tilting device. The TEM specimens were preshadowed with platinum and then rotary coated with carbon in the same device. After stripping the RBC-Pt-C composite film, the RBC's were dissolved in 2.5N HNO3 followed by 0.2N NaOH leaving the preshadowed surface replicas showing positive topography.

Formation of Dislocation Channels in Neutron Irradiated Molybdenum

1972 ◽  
Vol 30 ◽  
pp. 672-673
Author(s):  
S. Mahajan
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Ambient Temperature ◽  
Room Temperature ◽  
Channel Formation ◽  
Early Stages ◽  
Transmission Electron ◽  
Three Stages ◽  
Two Stages ◽  
Polycrystalline Molybdenum

The evolution of dislocation channels in irradiated metals during deformation can be envisaged to occur in three stages: (i) formation of embryonic cluster free regions, (ii) growth of these regions into microscopically observable channels and (iii) termination of their growth due to the accumulation of dislocation damage. The first two stages are particularly intriguing, and we have attempted to follow the early stages of channel formation in polycrystalline molybdenum, irradiated to 5×1019 n. cm−2 (E > 1 Mev) at the reactor ambient temperature (∼ 60°C), using transmission electron microscopy. The irradiated samples were strained, at room temperature, up to the macroscopic yield point.Figure 1 illustrates the early stages of channel formation. The observations suggest that the cluster free regions, such as A, B and C, form in isolated packets, which could subsequently link-up to evolve a channel.

A crystallographic analysis of the CoSi/Si(111) interface using Transmission Electron Microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 574-575
Author(s):  
A.C. Daykin ◽  
C.J. Kiely ◽  
R.C. Pond ◽  
J.L. Batstone
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Defect Structure ◽  
Room Temperature ◽  
Theoretical Method ◽  
Crystallographic Analysis ◽  
Si Substrate ◽  
Transmission Electron ◽  
Theoretical Predictions

When CoSi2 is grown onto a Si(111) surface it can form in two distinct orientations. A-type CoSi2 has the same orientation as the Si substrate and B-type is rotated by 180° degrees about the [111] surface normal.One method of producing epitaxial CoSi2 is to deposit Co at room temperature and anneal to 650°C.If greater than 10Å of Co is deposited then both A and B-type CoSi2 form via a number of intermediate silicides .The literature suggests that the co-existence of A and B-type CoSi2 is in some way linked to these intermediate silicides analogous to the NiSi2/Si(111) system. The phase which forms prior to complete CoSi2 formation is CoSi. This paper is a crystallographic analysis of the CoSi2/Si(l11) bicrystal using a theoretical method developed by Pond. Transmission electron microscopy (TEM) has been used to verify the theoretical predictions and to characterise the defect structure at the interface.

Structural Investigation of Iron Particles Used for Magnetic Recording Media

1980 ◽  
Vol 38 ◽  
pp. 406-407
Author(s):  
Alfred Baltz
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Microscope ◽  
Structural Investigation ◽  
Magnetic Interaction ◽  
Recording Media ◽  
Magnetic Recording Media ◽  
Recording Medium ◽  
Iron Particles ◽  
Transmission Electron

As part of a program to develop iron particles for next generation recording disk medium, their structural properties were investigated using transmission electron microscopy and electron diffraction. Iron particles are a more desirable recording medium than iron oxide, the most widely used material in disk manufacturing, because they offer a higher magnetic output and a higher coercive force. The particles were prepared by a method described elsewhere. Because of their strong magnetic interaction, a method had to be developed to separate the particles on the electron microscope grids.

Synthesis and TEM study of Ag–In–(Eu, Ce) ternary approximants

2009 ◽  
Vol 224 (1-2) ◽  
Author(s):  
Kazue Nishimoto ◽  
Miki Muraki ◽  
Ryuji Tamura
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Room Temperature ◽  
Transmission Electron

AbstractTernary Ag–In–(Eu, Ce) 1/1 approximants are synthesized and their structures are studied by transmission electron microscopy (TEM). For both the approximants, superlattice spots are clearly observed at room temperature, and the superstructures of the Ag–In–(Eu, Ce) approximants are found to be similar to those of Cd

Preparation of Straight and Orderly Polypyrrole Microrods through Soft Template Methods

2011 ◽  
Vol 306-307 ◽  
pp. 679-683
Author(s):  
Li Bo Sun ◽  
Yuan Chang Shi ◽  
Lin Ya Chu ◽  
Bing Chang Zhang ◽  
Jiu Rong Liu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Cetyltrimethylammonium Bromide ◽  
Growth Process ◽  
Room Temperature ◽  
Oxidative Polymerization ◽  
Soft Template ◽  
Microemulsion System ◽  
Transmission Electron ◽  
The Impact

The straight and orderly microrods of polypyrrole(PPy) was synthesized in a microemulsion system consisted of cetyltrimethylammonium bromide(CTAB), n-pentanol, water and pyrrole by chemical oxidative polymerization, in which CTAB was used as soft templates and APS was used as the oxidant. Fourier-transform infrared spectroscopy (FTIR) was used to characterize the structure of the PPy microrods. Transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM) was used to characterize the morphology of the samples. We discussed the impact of temperature, the adding way of the oxidant, the amount of cosurfactant n-pentanol to the morphology of PPy microrods. The results showed that straight and orderly PPy microrods with a diameter about 300nm and a length up to 20μm were synthesized when the temperature was kept at room temperature (25°C), the dropping time of APS was more than 1.5h, the ratio of CTAB to n-pentanol was 0.6:1, and the polymerization time was about 24h. We studied the growth process of PPy microrods by HTEM analysis. HTEM images revealed that the growth process of PPy changed from hollow microrods, semi-hollow microrods, and finally solid microrods.

Nanotwinned Surface on a Ternary Titanium Alloy with Increased Hardness Induced under Nanoindentations

2016 ◽  
Vol 874 ◽  
pp. 323-327
Author(s):  
Hong Xiu Zhou ◽  
Ming Lei Li ◽  
Neng Dong Duan ◽  
Bo Wang ◽  
Zhi Feng Shi ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Surface Roughness ◽  
Titanium Alloy ◽  
Chemical Mechanical Polishing ◽  
Material Removal ◽  
Room Temperature ◽  
Chemical Reagents ◽  
Transmission Electron ◽  
High Temperature High Pressure

A nanotwinned surface is formed on a titanium alloy under nanoindentations. Prior to nanoindentation, blocks of a ternary titanium alloy are machined by chemical mechanical polishing. The surface roughness Ra and peak-to-valley values are 1.135 nm and 8.82 nm, respectively. The hardness in the indented surface is greatly increased, indicated from the load-displacement curves compared to the polished surfaces. Nanotwins are confirmed using transmission electron microscopy. The nanotwinned surface is uniformly generated by nanoindentations at room temperature, which is different from previous findings, in which high temperature, high pressure, or chemical reagents are usually used. The nanotwinned surface is produced by pure mechanical stress, neither material removal nor addition.

scholarly journals In situ environmental HRTEM discloses low temperature carbon soot oxidation by ceria–zirconia at the nanoscale

2019 ◽  
Vol 55 (27) ◽  
pp. 3876-3878 ◽  
Author(s):  
Eleonora Aneggi ◽  
Jordi Llorca ◽  
Alessandro Trovarelli ◽  
Mimoun Aouine ◽  
Philippe Vernoux
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Temperature ◽  
Room Temperature ◽  
Soot Oxidation ◽  
Environmental Transmission ◽  
Transmission Electron ◽  
Carbon Soot ◽  
Environmental Transmission Electron Microscopy

In situ environmental transmission electron microscopy discloses room temperature carbon soot oxidation by ceria–zirconia at the nanoscale.

Sign in / Sign up

Export Citation Format

Share Document