On the Roles of Temperature and Interfaces in Irradiation and Thermally Induced Solid State Amorphization

1995 ◽  
Vol 398 ◽  
Author(s):  
L.M. Wang ◽  
W.L. Gong ◽  
R.C. Ewing ◽  
W.J. Webert
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Pressure ◽  
Grain Boundaries ◽  
Irradiation Temperature ◽  
Free Surfaces ◽  
Thermally Induced ◽  
Transmission Electron ◽  
Increasing Temperature ◽  
State Amorphization

ABSTRACTThe roles of irradiation temperature and interfaces (free surfaces and grain boundaries) in irradiation- and thermally- induced amorphization of ceramics (coesite, apatite, olivines and spinels) have been studied by transmission electron microscopy (TEM). The irradiations were performed with 1.5 MeV Kr+, 200 keV and 1 MeV electrons over a wide temperature range (20-700 K). The critical amorphization dose at which amorphization is complete, Dc, increased with increasing irradiation temperature for most materials except coesite (a high pressure polymorph of Si02) which showed a decreasing Dc with increasing temperature under 1 MeV electron irradiation. Although amorphization may occur directly within a displacement cascade or by cascade overlap, this study shows that free surfaces and grain boundaries are favorable sites for nucleation of amorphous volumes. Once the amorphous volume is formed at interfaces, it may grow rapidly under continued irradiation. Coesite which has a glass transition temperature higher than its melting temperature underwent spontaneous amorphization during thermal annealing at 1200 K. This thermally-induced amorphization also started at free surface and grain boundaries and propagated into the interior of the crystal. The interface-mediated amorphization is analogous to the process of thermodynamic melting.

Structure, Thermal Stability and Properties of Grain Boundaries of Submicrocrystalline Mo Obtained by Severe Plastic Deformation

2012 ◽  
Vol 326-328 ◽  
pp. 674-681 ◽  
Author(s):  
Vladimir V. Popov ◽  
Galina P. Grabovetskaya ◽  
A.V. Sergeev ◽  
I.P. Mishin
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Transmission Electron Microscopy ◽  
Plastic Deformation ◽  
High Pressure ◽  
Severe Plastic Deformation ◽  
Grain Boundaries ◽  
High Pressure Torsion ◽  
Emission Mössbauer Spectroscopy ◽  
Transmission Electron

The structure of submicrocrystalline Mo, obtained by high pressure torsion, its thermal stability and the state of grain boundaries have been studied by transmission electron microscopy and emission Mössbauer spectroscopy.

Atomic Structure and Property Correlation in Pulsed Laser Deposited High -Tc Films

1998 ◽  
Vol 526 ◽  
Author(s):  
R. Kalyanaraman ◽  
S. Oktyabrsky ◽  
K. Jagannadham ◽  
J. Narayan
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Grain Boundaries ◽  
Atomic Structure ◽  
Substrate Surface ◽  
Pulsed Laser ◽  
Structure And Property ◽  
Transmission Electron ◽  
Tilt Boundaries ◽  
Z Contrast

AbstractThe atomic structure of grain boundaries in pulsed laser deposited YBCO/MgO thin films have been studied using transmission electron microscopy. The films have perfect texturing with YBCO(001)//MgO(001), giving rise to low-angle [001] tilt boundaries from the grains with the c-axis normal to substrate surface. Low angle grain boundaries have been found to be aligned preferentially along (100) and (110) interface planes. The energy of (110) boundary planes described by an alternating array of [100] and [010] dislocation is found to be comparable to the energy of a (100) boundary. The existence of these split dislocations is shown to further reduce the theoretical current densities of these boundaries indicating that (110) boundaries carry less current as compared to (100) boundaries of the same misorientation angle. Further, Z-contrast transmission electron microscopy of a 42° asymmetric high-angle grain boundary of YBCO shows evidence for the existence of boundary fragments and a reduced atomic density along the boundary plane

Dislocations and stacking faults in stainless steel

1957 ◽  
Vol 240 (1223) ◽  
pp. 524-538 ◽  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Stainless Steel ◽  
Grain Boundaries ◽  
Stacking Faults ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Thin Sections ◽  
Partial Dislocations ◽  
Transmission Electron

Further experiments by transmission electron microscopy on thin sections of stainless steel deformed by small amounts have enabled extended dislocations to be observed directly. The arrangement and motion of whole and partial dislocations have been followed in detail. Many of the dislocations are found to have piled up against grain boundaries. Other observations include the formation of wide stacking faults, the interaction of dislocations with twin boundaries, and the formation of dislocations at thin edges of the foils. An estimate is made of the stacking-fault energy from a consideration of the stresses present, and the properties of the dislocations are found to be in agreement with those expected from a metal of low stacking-fault energy.

Structural, morphological, and magnetic study of nanocrystalline cobalt-copper powders synthesized by the polyol process

1995 ◽  
Vol 10 (6) ◽  
pp. 1546-1554 ◽  
Author(s):  
G.M. Chow ◽  
L.K. Kurihara ◽  
K.M. Kemner ◽  
P.E. Schoen ◽  
W.T. Elam ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Copper Powders ◽  
Face Centered ◽  
Increasing Temperature ◽  
X Ray Absorption

Nanocrystalline CoxCu100−x (4 ⋚ x ⋚ 49 at. %) powders were prepared by the reduction of metal acetates in a polyol. The structure of powders was characterized by x-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), extended x-ray absorption fine structure (EXAFS) spectroscopy, solid-state nuclear magnetic resonance (NMR) spectroscopy, and vibrating sample magnetometry (VSM). As-synthesized powders were composites consisting of nanoscale crystallites of face-centered cubic (fcc) Cu and metastable face-centered cubic (fcc) Co. Complementary results of XRD, HRTEM, EXAFS, NMR, and VSM confirmed that there was no metastable alloying between Co and Cu. The NMR data also revealed that there was some hexagonal-closed-packed (hcp) Co in the samples. The powders were agglomerated, and consisted of aggregates of nanoscale crystallites of Co and Cu. Upon annealing, the powders with low Co contents showed an increase in both saturation magnetization and coercivity with increasing temperature. The results suggested that during preparation the nucleation of Cu occurred first, and the Cu crystallites served as nuclei for the formation of Co.

Crystal structures of high-pressure phases formed in Si by laser irradiation

Microscopy ◽  
2018 ◽  
Vol 67 (1) ◽  
pp. 30-36
Author(s):  
Hiroyuki Iwata ◽  
Daisuke Kawaguchi ◽  
Hiroyasu Saka
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
High Pressure ◽  
Laser Beam ◽  
Crystal Structures ◽  
Laser Irradiation ◽  
Pulse Laser ◽  
Transmission Electron ◽  
Micro Cracks ◽  
Pressure Phase

Abstract Internal modification induced in Si by a permeable pulse laser was investigated by transmission electron microscopy. A laser induced modified volume (LIMV) was a cylindrical rod along the track of a laser beam with the head at the focus of the laser beam. In the LIMV, beside voids, dislocations, micro-cracks and what had been supposed to be an unidentified high-pressure phase (hpp) of Si were observed in LIMV. The so-called ‘hpp’ was identified mostly as diamond Si.

Sign in / Sign up

Export Citation Format

Share Document