A Spectroscopic and Thermodynamic Investigation of Mercuric Iodide Physically Confined in Porous Glass Hosts

1994 ◽  
Vol 366 ◽  
Author(s):  
D. O. Henderson ◽  
R. Mu ◽  
A. Ueda ◽  
A. Burger ◽  
K. T. Chen ◽  
...  
Keyword(s):  
Electronic Spectra ◽  
Energy Gap ◽  
Bulk Material ◽  
Mercuric Iodide ◽  
Thermodynamic Investigation ◽  
Scanning Calorimetry ◽  
Dsc Measurements ◽  
Β Phase ◽  
Material Evidence ◽  
New Phase

ABSTRACTRaman and electronic spectra and results from differential scanning calorimetry (DSC) are reported for mercuric iodide (HgI2) confined in four different pore-sized glass hosts. The Raman spectra reveal peaks at 39 and 141 cm−1 that indicate the confined HgI2 is stabilized at 300 K in a modified orthorhombic (yellow) β-phase which is observed at 400 K for the bulk material. An additional band begins to appear at 145 cm−1 for pore radii smaller than 3.75 nm suggesting the presence of new phase of confined HgI2. The DSC measurements show the melting and freezing transitions of confined β-HgI2 are depressed from values reported for the bulk material and the depression increases as the pore size decreases. No transition is observed in the DSC measurement which could be attributed to the α→β transition for the confined material. Evidence supporting the new phase of HgI2 is observed in the electronic spectra of the confined HgI2 by the appearance of an energy gap transitions located at 2.7 eV.

scholarly journals Nucleation of the β-polymorph in Composites of Poly(propylene) and Graphene Nanoplatelets

2019 ◽  
Vol 3 (2) ◽  
pp. 38 ◽  
Author(s):  
Valentina Guerra ◽  
Chaoying Wan ◽  
Tony McNally
Keyword(s):  
Graphene Nanoplatelets ◽  
Laboratory Scale ◽  
Degree Of Crystallinity ◽  
Mixing Efficiency ◽  
Scanning Calorimetry ◽  
Dsc Measurements ◽  
Β Phase ◽  
A Value ◽  
Twin Screw ◽  
Poly Propylene

The effects of graphene nanoplatelets (GNPs) on the nucleation of the β-polymorph of polypropylene (PP) were studied when melt-mixed at loadings of 0.1–5 wt % using a laboratory scale twin-screw (conical) extruder and a twin-screw (parallel) extruder with L/D = 40. At low GNP loadings (i.e., ≤0.3 wt %), the mixing efficiency of the extruder used correlated with the β-nucleating activity of GNPs for PP. GNP agglomeration at low loadings (<0.5 wt %) resulted in an increase in the β-phase fraction (Kβ) of PP, as determined from X-ray diffraction measurements, up to 37% at 0.1 wt % GNPs for composites prepared using a laboratory scale twin-screw (conical) extruder. The level of GNP dispersion and distribution was better when the composites were prepared using a 16-mm twin-screw (parallel) extruder, giving a Kβ increase of 24% upon addition of 0.1 wt % GNPs to PP. For GNP loadings >0.5 wt %, the level of GNP dispersion in PP did not influence the growth of β-crystals, where Kβ reached a value of 24%, regardless of the type of extruder used. From differential scanning calorimetry (DSC) measurements, the addition of GNPs to PP increased the crystallization temperature (Tc) of PP by 14 °C and 10 °C for the laboratory scale extruder and 16-mm extruder, respectively, confirming the nucleation of PP by GNPs. The degree of crystallinity (Xc%) of PP increased slightly at low GNP additions (≤0.3 wt %), but then decreased with increasing GNP content.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

Investigations on the polymorphism and pseudopolymorphism of clobetasone butyrate

2011 ◽  
Vol 76 (5) ◽  
pp. 553-566
Author(s):  
Christian Näther ◽  
Inke Jeß
Keyword(s):  
Room Temperature ◽  
Polymorphic Form ◽  
Stable Form ◽  
Scanning Calorimetry ◽  
Amorphous Form ◽  
Space Group ◽  
Dsc Measurements ◽  
Independent Molecules ◽  
Solvent Molecules ◽  
Similar Conformation

Clobetasone butyrate was investigated for polymorphism and pseudopolymorphism. Solvent mediated conversion experiments reveal that the commercially available form I represent the thermodynamically most stable form at room temperature and DSC measurements shows that it should also be the most stable form until melting. Form I crystallizes in space groupP212121with three crystallographically independent molecules of similar conformation. From methanol an additional pseudo polymorphic form was discovered. In the crystal structure (space groupP212121) the solvent molecules are connected to the clobetasone butyrate molecules by O–H···O hydrogen bonding. Investigations of the solvate using thermogravimetry, differential thermoanalysis as well as differential scanning calorimetry proves, that on solvent removal an amorphous form is obtained that crystallizes into form I on further heating.

Effects of Aging on the Microstructure and Phase Transformation Behavior of Cu-Al-Mn Shape Memory Alloy

2021 ◽  
Vol 882 ◽  
pp. 21-27
Author(s):  
Seyed Veghar Seyedmohammadi ◽  
Amin Radi ◽  
Guney Guven Yapici
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Aging Treatment ◽  
Scanning Calorimetry ◽  
Dsc Measurements ◽  
Peak Aged Condition ◽  
Peak Aged ◽  
Rolled Condition ◽  
The One ◽  
Effects Of Aging

In the present work, the effects of artificial aging treatment on the transformation temperatures and hardness of Cu-Al-Mn shape memory alloy have been investigated. The aging processes have been performed on the one-time re-melted and 90% rolled samples. Differential scanning calorimetry reveals that reverse transformation is present for the re-melted sample which is aged at 400°C. However, in 90% rolled condition, this transformation takes place at 200°C and 300°C. Hardness examination shows that the aged specimens possess higher values in hardness in comparison to un-aged samples at all studied temperatures. Although, the peak-aged condition was demonstrated at 300°C for the re-melted sample, the rolled sample displayed increased hardness levels up to 500°C. Based on the DSC measurements and microstructural observations, it can be asserted that the thermo-mechanical processing including rolling plus aging at 300°C provides favorable transformation characteristics for shape memory behavior.

scholarly journals A Facile Synthesis and Characterization of Highly Crystalline Submicro-Sized BiFeO3

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3035
Author(s):  
Dovydas Karoblis ◽  
Diana Griesiute ◽  
Kestutis Mazeika ◽  
Dalis Baltrunas ◽  
Dmitry V. Karpinsky ◽  
...  
Keyword(s):  
Bismuth Ferrite ◽  
Cost Effective ◽  
Xrd Analysis ◽  
Synthetic Approach ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Dsc Measurements ◽  
Optimal Annealing Temperature ◽  
Synthesized Materials

In this study, a highly crystalline bismuth ferrite (BFO) powder was synthesized using a novel, very simple, and cost-effective synthetic approach. It was demonstrated that the optimal annealing temperature for the preparation of highly-pure BFO is 650 °C. At lower or higher temperatures, the formation of neighboring crystal phases was observed. The thermal behavior of BFO precursor gel was investigated by thermogravimetric and differential scanning calorimetry (TG-DSC) measurements. X-ray diffraction (XRD) analysis and Mössbauer spectroscopy were employed for the investigation of structural properties. Scanning electron microscopy (SEM) was used to evaluate morphological features of the synthesized materials. The obtained powders were also characterized by magnetization measurements, which showed antiferromagnetic behavior of BFO powders.

scholarly journals Luminescence of SiO2-BaF2:Tb3+, Eu3+ Nano-Glass-Ceramics Made from Sol–Gel Method at Low Temperature

Nanomaterials ◽  
2022 ◽  
Vol 12 (2) ◽  
pp. 259
Author(s):  
Natalia Pawlik ◽  
Barbara Szpikowska-Sroka ◽  
Tomasz Goryczka ◽  
Ewa Pietrasik ◽  
Wojciech A. Pisarski
Keyword(s):  
Sol Gel ◽  
Three Dimensional ◽  
Glass Ceramics ◽  
Emission Spectra ◽  
Scanning Calorimetry ◽  
Light Emitting ◽  
Co Doping ◽  
Dsc Measurements ◽  
Decay Times

The synthesis and characterization of multicolor light-emitting nanomaterials based on rare earths (RE3+) are of great importance due to their possible use in optoelectronic devices, such as LEDs or displays. In the present work, oxyfluoride glass-ceramics containing BaF2 nanocrystals co-doped with Tb3+, Eu3+ ions were fabricated from amorphous xerogels at 350 °C. The analysis of the thermal behavior of fabricated xerogels was performed using TG/DSC measurements (thermogravimetry (TG), differential scanning calorimetry (DSC)). The crystallization of BaF2 phase at the nanoscale was confirmed by X-ray diffraction (XRD) measurements and transmission electron microscopy (TEM), and the changes in silicate sol–gel host were determined by attenuated total reflectance infrared (ATR-IR) spectroscopy. The luminescent characterization of prepared sol–gel materials was carried out by excitation and emission spectra along with decay analysis from the 5D4 level of Tb3+. As a result, the visible light according to the electronic transitions of Tb3+ (5D4 → 7FJ (J = 6–3)) and Eu3+ (5D0 → 7FJ (J = 0–4)) was recorded. It was also observed that co-doping with Eu3+ caused the shortening in decay times of the 5D4 state from 1.11 ms to 0.88 ms (for xerogels) and from 6.56 ms to 4.06 ms (for glass-ceramics). Thus, based on lifetime values, the Tb3+/Eu3+ energy transfer (ET) efficiencies were estimated to be almost 21% for xerogels and 38% for nano-glass-ceramics. Therefore, such materials could be successfully predisposed for laser technologies, spectral converters, and three-dimensional displays.

scholarly journals Piezoelectric Properties of Zinc Oxide/Iron Oxide filled Polyvinylidene fluoride Nanocomposite Fibers

2021 ◽  
Author(s):  
Abdulrahman Mohmmed AlAhzm ◽  
Maan Omar Alejli ◽  
Deepalekshmi Ponnamma ◽  
Yara Elgawady ◽  
Mariam Al Ali Al-Maadeed
Keyword(s):  
Zinc Oxide ◽  
Iron Oxide ◽  
Polyvinylidene Fluoride ◽  
Output Voltage ◽  
Mechanical Energy ◽  
Scanning Calorimetry ◽  
Power Sources ◽  
Hybrid Nanomaterial ◽  
Β Phase ◽  
Nanocomposite Fibers

Abstract Piezoelectric nanogenerators (PENG) with flexible and simple design have pronounced significance in fabricating sustainable devices for self-powering electronics. This study demonstrates the fabrication of electrospun nanocomposite fibers from polyvinylidene fluoride (PVDF) filled Zinc Oxide (ZnO)/Iron Oxide (FeO) nanomaterials. The nanocomposite fiber based flexible PENG showed piezoelectric output voltage of 5.9 V when 3 wt.% of ZnO/FeO hybrid nanomaterial was introduced, which was 29.5 times higher than the neat PVDF. No apparent decline in output voltage was observed for almost 2000 seconds attributed to the outstanding durability. This higher piezoelectric output performance is correlated with the β-phase transformation studies from the Fourier transformation infrared spectroscopy and the crystallinity studies from the differential scanning calorimetry. Both these studies show respective enhancement of 3.79 and 2.16 % in the β-phase crystallinity values of PVDF-ZnO/FeO 3 wt.% composite. Higher dielectric constant value obtained for the same composite (3 times higher than the neat PVDF) confirms the increased energy storage efficiency as well. Thus the proposed soft and flexible PENG is a promising mechanical energy harvester, and its good dielectric properties reveals the ability to use this material as good power sources for wearable and flexible electronic devices.

The Metastable Phase Responsible for Hardenig in an Al-Mg Alloy Aged at 473K

2013 ◽  
Vol 748 ◽  
pp. 123-127 ◽  
Author(s):  
Koichiro Fukui ◽  
Ayaka Mori ◽  
Masanori Mitome ◽  
Mahoto Takeda
Keyword(s):  
Precipitation Hardening ◽  
Vickers Microhardness ◽  
Layer Structure ◽  
Metastable Phase ◽  
Mg Alloy ◽  
Stable Phase ◽  
Precipitation Behavior ◽  
Dsc Measurements ◽  
Β Phase ◽  
Phase Precipitate

The present work investigated precipitation behavior in an Al-17at%Mg alloy isothermally aged at 473K, by means of Vickers microhardness tests, DSC measurements and TEM observations. A quantitative analysis of DSC measurements revealed that the metastable β-phase precipitates mainly contribute to precipitation hardening of this alloy aged at 473K. The present STEM-EDX observations confirmed that the metastable β-phase precipitate has a layer structure with a composition similar to the stable phase (Al3Mg2).

Effects of Cooling Rate and Sn Addition on the Microstructure of Ti-Nb-Sn Alloys

2011 ◽  
Vol 172-174 ◽  
pp. 190-195 ◽  
Author(s):  
Giorgia T. Aleixo ◽  
Eder S.N. Lopes ◽  
Rodrigo Contieri ◽  
Alessandra Cremasco ◽  
Conrado Ramos Moreira Afonso ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Melting Furnace ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Β Phase ◽  
Arc Melting ◽  
Ti Alloys ◽  
Ω Phase

Ti-based alloys present unique properties and hence, are employed in several industrial segments. Among Ti alloys, β type alloys form one of the most versatile classes of materials in relation to processing, microstructure and mechanical properties. It is well known that heat treatment of Ti alloys plays an important role in determining their microstructure and mechanical behavior. The aim of this work is to analyze microstructure and phases formed during cooling of β Ti-Nb-Sn alloy through different cooling rates. Initially, samples of Ti-Nb-Sn system were prepared through arc melting furnace. After, they were subjected to continuous cooling experiments to evaluate conditions for obtaining metastable phases. Microstructure analysis, differential scanning calorimetry and X-ray diffraction were performed in order to evaluate phase transformations. Depending on the cooling rate and composition, α” martensite, ω phase and β phase were obtained. Elastic modulus has been found to decrease as the amount of Sn was increased.

scholarly journals Microstructural and Mechanical Response of NiTi Lattice 3D Structure Produced by Selective Laser Melting

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 814 ◽  
Author(s):  
Carlo Alberto Biffi ◽  
Paola Bassani ◽  
Jacopo Fiocchi ◽  
Ausonio Tuissi
Keyword(s):  
Martensitic Transformation ◽  
Selective Laser Melting ◽  
Mechanical Response ◽  
Electron Backscatter Diffraction ◽  
Bulk Material ◽  
Niti Alloy ◽  
3D Structure ◽  
Lattice Structures ◽  
Laser Melting ◽  
Scanning Calorimetry

Nowadays, additive manufacturing (AM) permits to realize complex metallic structural parts, and the use of NiTi alloy, known as Nitinol, allows the integration of specific functions to the AM products. One of the most promising designs for AM is concerning the use of lattice structures that show lightweight, higher than bulk material deformability, improved damping properties, high exchange surface. Moreover, lattice structures can be realized with struts, having dimensions below 1 mm—this is very attractive for the realization of Nitinol components for biomedical devices. In this light, the present work regarded the experimental characterization of lattice structures, produced by selective laser melting (SLM), by using Ni-rich NiTi alloy. Differential scanning calorimetry (DSC), electron backscatter diffraction (EBSD), and compression testing were carried out for analyzing microstructure, martensitic transformation (MT) evolution, and superelasticity response of the SLMed lattice samples. The lattice microstructures were compared with those of the SLMed bulk material for highlighting differences. Localized martensite was detected in the nodes zones, where the rapid solidification tends to accumulate solidification stresses. An increase of martensitic transformation temperatures was also observed in lattice NiTi.

Sign in / Sign up

Export Citation Format

Share Document