Physicochemical and Electrical Properties of RF Magnetron Sputtered Lead Zirconate Titanate Thin Films

1994 ◽  
Vol 361 ◽  
Author(s):  
B. Ea Kim ◽  
M.C. Hugon ◽  
F. Varniere ◽  
B. Agius ◽  
H. Achard ◽  
...  
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Lead Zirconate Titanate ◽  
Deuteron Beam ◽  
Lead Zirconate ◽  
Nuclear Reaction Analysis ◽  
Nominal Composition ◽  
Pzt Thin Films ◽  
Zirconate Titanate ◽  
Pzt Films

ABSTRACTDue to their high dielectric constant, good chemical stability and good insulating properties, lead zirconate titanate (PZT) thin films are considered as promising materials to replace Si3N4 and Ta2O5 for use as the capacitor dielectric in future high density DRAMs. Moreover, the ferroelectric quality of PZT films also allows use of this material in non volatile memories. In this paper, we investigate the properties of PZT films deposited from an oxide target of nominal composition {Pb1.1(Zr0.55,Ti0.45)O3} in a radio frequency (rf) magnetron sputtering system. The Pt(deposited at 450°C)/[TiN/Ti/BPSG/Si] structure annealed at 450°C at 10−6 mbar (Pt(450°C)/{TiN/Ti/BPSG/Si}450°c,10–6mbar) was used as a substrate material in this work. The PZT films were deposited at different pressures, and different substrate temperatures ranging from floating temperature to 400°C; the thicknesses of the sputtered films were in the 15–720 nm range. The kinetics of the sputtering process and the effect of sputtering parameters on film composition have been studied and related to the continuously monitored optical emission of the plasma. The relative cation and oxygen compositions of the films were determined by a new method based on the simultaneous use of Rutherford Backscattering Spectrometry (RBS) and Nuclear Reaction Analysis (NRA) induced by a deuteron beam. The conditions for the deposition of stoichiometric PZT thin films were established.Electrical characterizations of the PZT films including resistivity, dielectric constant, dissipation factor were studied as a function of the temperature. From initial electrical measurements, it appears that a dielectric constant of 740 can be obtained for PZT 55/45 films deposited on a previously annealed Pt/TiN/Ti/BPSG/Si structure.

Physicochemical Properties of Rf Magnetron Sputtered Lead Zirconate Titanate Thin Films

1991 ◽  
Vol 243 ◽  
Author(s):  
E. Catitan ◽  
B. Agius ◽  
H. Achard ◽  
J.P. Joly ◽  
J.C. Cheang Wong ◽  
...  
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Deuteron Beam ◽  
Optical Emission ◽  
Rf Magnetron Sputtering ◽  
Lead Zirconate ◽  
Nuclear Reaction Analysis ◽  
Nominal Composition ◽  
Zirconate Titanate ◽  
Kinetics Of

AbstractLead zirconate titanate thin films have been grown by rf magnetron sputtering an oxide target of nominal composition [Pb(Zr0.55,Ti0.45)O3 or PZT] in argon. The kinetics of the sputtering process and the effect of sputtering parameters on film composition have been studied and related to the continuously monitored optical emission of the plasma. The relative and absolute cation and oxygen compositions of the thin films were determined by a new method based on the simultaneous use of Rutherford backscattering spectroscopy (RBS) and nuclear reaction analysis (NRA) induced by a deuteron beam. The conditions for the deposition at room temperature of stoichiometric PZT films were established.

Microstructure of Solution-Processed Lead Zirconate Titanate (PZT) Thin Films

1991 ◽  
Vol 74 (6) ◽  
pp. 1455-1458 ◽  
Author(s):  
Altaf H. Carim ◽  
Bruce A. Tuttle ◽  
Daniel H. Doughty ◽  
Sheri L. Martinez
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
Solution Processed ◽  
Pzt Thin Films ◽  
Zirconate Titanate

Effect of Annealing Treatment on PZT Thin Fiilm Properties Using Oxygen 18 Depth Profiling Technique

1998 ◽  
Vol 541 ◽  
Author(s):  
F. Ayguavives ◽  
B. Ea-Kim ◽  
B. Agius ◽  
I. Vickridge ◽  
A. I. Kingon
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Plasma Deposition ◽  
Annealing Treatment ◽  
Nuclear Reaction Analysis ◽  
Nominal Composition ◽  
Pzt Thin Films ◽  
Pzt Thin Film ◽  
Metallic Target

AbstractLead zirconate titanate (PZT) thin films have been deposited in a reactive argon/oxygen gas mixture from a metallic target of nominal composition Pb1.1(Zr0.4Ti0.6)O3 by rf magnetron sputtering on Si substrates and RuO2/SiO2/Si structures. During plasma deposition, in situ Optical Emission Spectroscopy (OES) measurements clearly show a correlation between the evolution of characteristic atomic emission line intensities and the thin film composition determined by simultaneous Rutherford Backscattering Spectroscopy (RBS) and Nuclear Reaction Analysis (NRA). As a result, the cathode surface state can be monitored by OES to ensure a good compositional transferability from the target to the film and reproducibility of thin film properties for given values of deposition parameters. Electrical properties and crystallization have been optimized with a 90 nm PZT thin film grown on RuO2 electrodes. These PZT films, annealed with a very modest thermal budget (550°C) are fatigue-free and show very low leakage currents (J=2.10−8 A/cm2 at 1 V). The use of a metallic target allows us to control the oxygen incorporation in the PZT thin film and also, using 18O as a tracer, to study the oxygen vacancy migration which plays a key role in fatigue, leakage current, and electrical degradation/breakdown in PZT thin films.

EFFECT OF PRE-HEATING TEMPERATURE ON THE CHARACTERISTICS OF PZT THIN FILMS GROWN BY USING A TRIOL SOL–GEL ROUTE

2007 ◽  
Vol 14 (02) ◽  
pp. 229-234
Author(s):  
SARAWUT THOUNTOM ◽  
MANOCH NAKSATA ◽  
KENNETH MACKENZIE ◽  
TAWEE TUNKASIRI
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Heating Temperature ◽  
Ferroelectric Properties ◽  
Sol Gel ◽  
Hysteresis Loops ◽  
Lead Zirconate ◽  
Pzt Thin Films ◽  
Pzt Films ◽  
Ferroelectric Hysteresis

Lead zirconate titanate (PZT) films with compositions near the morphotropic phase boundary were fabricated on Pt (111)/ Ti / SiO 2/ Si (100) using the triol sol–gel method. The effect of the pre-heating temperature on the phase transformations, microstructures, electrical properties, and ferroelectric properties of the PZT thin films was investigated. Randomly oriented PZT thin films pre-heated at 400°C for 10 min and annealed at 600°C for 30 min showed well-defined ferroelectric hysteresis loops with a remnant polarization of 26.57 μC/cm2 and a coercive field of 115.42 kV/cm. The dielectric constant and dielectric loss of the PZT films were 621 and 0.0395, respectively. The microstructures of the thin films are dense, crack-free, and homogeneous with fine grains about 15–20 nm in size.

Growth and characterization of lead zirconate titanate (PZT) thin films

2013 ◽  
Vol 21 (11) ◽  
pp. 2893-2899 ◽  
Author(s):  
张翊 ZHANG Yi ◽  
潘峰 PAN Feng ◽  
包达群 BAO Da-qun ◽  
王建艳 WANG Jian-yan ◽  
郭航 GUO Hang
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
Pzt Thin Films ◽  
Zirconate Titanate

Effect of oxygen partial pressure on texture development in lead zirconate titanate thin films processed from metalorganic precursors

1999 ◽  
Vol 14 (12) ◽  
pp. 4615-4620
Author(s):  
Jarrod L. Norton ◽  
Gerald L. Liedl ◽  
Elliott B. Slamovich
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
Texture Development ◽  
Pure Oxygen ◽  
Maximum Temperature ◽  
Zirconate Titanate ◽  
Liquid Precursors ◽  
Pzt Films ◽  
Switching Temperature

Metalorganic liquid precursors were used to examine the effects of processing atmosphere on texture development in oriented Pb(Zr0.60Ti0.40)O3 thin films. After removal of organic ligands via pyrolysis, the films were heated at 25 °C/min in a 5% H2/Ar atmosphere until a switching temperature, after which the atmosphere was switched to pure oxygen. The films were heated to a maximum temperature of 650 °C with switching temperatures ranging from 450 to 600 °C. The degree of (111) orientation in the lead zirconate titanate (PZT) films increased with increasing switching temperature, resulting in highly textured (111) PZT films. These results suggest that atmosphere control plays a significant role in texture development during rapid thermal processing.

Sign in / Sign up

Export Citation Format

Share Document