Practical and Fundamental Studies of Nanocrystalline Composite Thin Films

1994 ◽  
Vol 356 ◽  
Author(s):  
Yang-Tse Cheng ◽  
Boqin Qiu ◽  
Simon Tung ◽  
J. P. Blanchard ◽  
G. Drew
Keyword(s):  
Grain Size ◽  
Wear Rate ◽  
Electron Probe ◽  
Friction And Wear ◽  
Composite Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Practical Applications ◽  
Transmission Electron ◽  
Nanocrystalline Composite

AbstractNanocrytslline composite films of Ag-Mo and Ag-Ni have been made by a co-deposition technique in UHV. The structure and composition have been studied by x-ray diffraction (XRD), transmission electron microscopy (TEM), and electron probe microanalysis (EPMA). For practical applications, the friction coefficient and wear rate were measured using a pin-on-plate machine for Ag-Mo composites deposited on steel. For fundamental studies, the hardness of the Ag-Ni composites deposited on oxidized Si wafers was measured using a nanoindenter. Experiments show that (1) reduction of friction and wear rate can be achieved using these nanocomposite coatings and (2) the hardness of the nanocomposites depends on the grain size. As the grain size of the Ag decreases from 100 to 10 nm, the hardness increases about 4 times.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Immobilization of hemoglobin on stable mesoporous multilamellar silica vesicles and their activity and stability

2005 ◽  
Vol 20 (10) ◽  
pp. 2682-2690 ◽  
Author(s):  
Yufang Zhu ◽  
Weihua Shen ◽  
Xiaoping Dong ◽  
Jianlin Shi
Keyword(s):  
Thermal Stability ◽  
Pore Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Practical Applications ◽  
Silica Material ◽  
Transmission Electron ◽  
Mesoporous Support ◽  
Adsorption Desorption ◽  
Thermal Stability Of

A stable mesoporous multilamellar silica vesicle (MSV) was developed with a gallery pore size of about 14.0 nm. A simulative enzyme, hemoglobin (Hb), was immobilized on this newly developed MSV and a conventional mesoporous silica material SBA-15. The structures and the immobilization of Hb on the mesoporous supports were characterized with x-ray diffraction, transmission electron microscopy, N2 adsorption-desorption isotherms, Fourier transform infrared, ultraviolet-visible spectroscopy, and so forth. MSV is a promising support for immobilizing Hb due to its large pore size and high Hb immobilization capacity (up to 522 mg/g) compared to SBA-15 (236 mg/g). Less than 5% Hb was leached from Hb/MSV at pH 6.0. The activity study indicated that the immobilized Hb retained most peroxidase activity compared to free Hb. Thermal stability of the immobilized Hb was improved by the proctetive environment of MSV and SBA-15. Such an Hb-mesoporous support with high Hb immobilization capacity, high activity, and enhanced thermal stability will be attractive for practical applications.

Microstructures and Properties of Fe/B-Fe Coating Used in Circulating Fluidized Bed Boiler

2011 ◽  
Vol 66-68 ◽  
pp. 1528-1532
Author(s):  
Qi Fa Tian ◽  
Hong Fei Sun
Keyword(s):  
Electron Probe ◽  
Circulating Fluidized Bed ◽  
Steel Substrate ◽  
Electric Arc ◽  
Bare Metal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Mechanical Performances ◽  
Electronic Microscope

Electric arc praying technology was used to produce Fe/B-Fe coating on the carbon steel substrate. The microstructures was studied by means of scanning electronic microscope (SEM), X-ray diffraction (XRD), transmission electron microscope (TEM) and electron probe microanalysis (EPMA). Mechanical performances, wear resistance of coating were tested . The results showed that the resistance to abrasion and corrosion of Fe/B-Fe coating was respectively 16 times and 5 to 6 times higher than those of bare metal.

TEM Study of FePt and FePt:C/FePt Composite Double-Layered Thin Films

2013 ◽  
Vol 275-277 ◽  
pp. 1952-1955
Author(s):  
Ling Fang Jin ◽  
Xing Zhong Li
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Magnetic Properties ◽  
Composite Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

New functional nanocomposite FePt:C thin films with FePt underlayers were synthesized by noneptaxial growth. The effect of the FePt layer on the ordering, orientation and magnetic properties of the composite layer has been investigated by adjusting FePt underlayer thickness from 2 nm to 14 nm. Transmission electron microscopy (TEM), together with x-ray diffraction (XRD), has been used to check the growth of the double-layered films and to study the microstructure, including the grain size, shape, orientation and distribution. XRD scans reveal that the orientation of the films was dependent on FePt underlayer thickness. In this paper, the TEM studies of both single-layered nonepitaxially grown FePt and FePt:C composite L10 phase and double-layered deposition FePt:C/FePt are presented.

Preparation and photoelectrochemical performance of nano Bi2S3–TiO2 composites

2018 ◽  
Vol 11 (03) ◽  
pp. 1850055 ◽  
Author(s):  
Senlin Li ◽  
Jinliang Huang ◽  
Xiangmei Ning ◽  
Yongchao Chen ◽  
Qingkui Shi
Keyword(s):  
Solvothermal Method ◽  
Composite Films ◽  
Great Influence ◽  
Photocurrent Density ◽  
Tetrabutyl Titanate ◽  
X Ray Diffraction ◽  
Photoelectrochemical Performance ◽  
X Ray ◽  
External Bias ◽  
Transmission Electron

TiO2 nanorod (NR) arrays were prepared on FTO by the simple hydrothermal synthesizing method. On this basis, a layer of Bi2S3 quantum dots (QDs) was covered on the surface of TiO2 NRs array by solvothermal method, by which the Nano Bi2S3/TiO2 NRs composites films were obtained. The phase structure, morphologies, optical absorptions and photoelectrochemical (PEC) properties of the as-prepared materials were characterized by X-ray diffraction (XRD), Scanning Electron Microscope (SEM), High Resolution Transmission Electron Microscopy (HRTEM), Ultraviolet–visible spectroscopy (UV-Vis), Photoluminescence (PL) and electrochemical workstation. The results indicate that the concentration of tetrabutyl titanate (TBT) has a great influence on the morphology of the film, with the increase of TBT content, the array of TiO2 NRs changed from loose to tight, and the thin films were cracked when the TBT volume is up to 0.7[Formula: see text]mL; The absorption of the TiO2 NRs array film to the visible light is enhanced significantly when sensitized with Bi2S3 and the absorption wavelength is increased from 400[Formula: see text]nm to 800[Formula: see text]nm. Compared with the pure TiO2, the fluorescence intensity of the TiO2/Bi2S3 NRs is weakened, and there is no obvious fluorescence diffraction peak. Under the irradiation of standard (AM1.5[Formula: see text]G 100[Formula: see text]mW/cm[Formula: see text], the photocurrent density of the composite film increased significantly. When the external bias voltage is 1.2[Formula: see text]V, the current density of the composite films is five times of that of the pure TiO2.

Estimation of Interdiffusivities of the Pseudo NiAl Binary Phase Formed in a Nickel-based Superalloy by Pack Cementation

2005 ◽  
Vol 20 (9) ◽  
pp. 2340-2347 ◽  
Author(s):  
H. Wei ◽  
X.F. Sun ◽  
Q. Zheng ◽  
H.R. Guan ◽  
Z.Q. Hu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Electron Probe ◽  
Pack Cementation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Binary Phase ◽  
Nickel Based Superalloy ◽  
Transmission Electron ◽  
Scanning Electron

The pseudo NiAl binary phase was formed in a nickel-based superalloy by pack cementation. Scanning electron microscopy, transmission electron microscopy, x-ray diffraction, electron probe microanalysis, and positron annihilation technique were used to characterize the pseudo NiAl binary phase. Based on reasonable assumptions, the chemical interdiffusivities of the pseudo NiAl binary phase were then assessed by means of the modified Wagner’s method. The results showed that the chemical interdiffusivities of the pseudo NiAl binary phase were about two orders of magnitude lower than those reported by others. The analysis indicated that the change in thermodynamic properties due to the additions of the microalloying atoms originally present in a superalloy could be responsible mainly for a decrease in chemical interdiffusivities.

Grain Size Dependent Magnetic Properties of Nanocrystalline Sm [BE]Co [BD][BJ]/Cu

2001 ◽  
Vol 703 ◽  
Author(s):  
L. Bessais ◽  
C. Djéga-Mariadassou ◽  
J. Zhang ◽  
V. Lalanne ◽  
A. Percheron-Guégan
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Rietveld Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Size Dependent ◽  
Transmission Electron ◽  
Average Grain Size ◽  
Magnetic Metal ◽  
Chemical Distribution

ABSTRACTThe evolution of both micro structural and magnetic properties of the Sm[BE]Co[BD][BJ] Cu powder, is studied as a function of soft co-milling time. The average grain size in the range 20 - 50 nm was determined by transmission electron microscopy coupled with x-ray diffraction using the Rietveld method. The particle shape and chemical distribution were investigated by elemental mapping, using wavelength dispersive x-ray analysis with electron microprobe analysis. The coercivity evolution shows that an optimum value of 6 kOe is obtained after 5 h co-milling. The microstructure analysis indicates that both materials are well mixed in nanometer scale. This technique appears as a potential route to synthesize nanocrystalline Sm[BE]Co[BD][BJ] isolated by non-magnetic metal Cu.

A Model for the Films Formation of Nb–Si–N Ternary Compound Deposited

2012 ◽  
Vol 476-478 ◽  
pp. 475-479 ◽  
Author(s):  
Yong Jun Jiang
Keyword(s):  
Film Formation ◽  
Composite Films ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nanoscale Structures ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Step Model ◽  
Si Content

By means of the reactive magnetron sputtering method, a series of Nb–Si–N composite films with different Si contents were deposited in an Ar, N2 and SiH4 mixture atmosphere. These films’ chemical composition, phase formation, microstructure and mechanical properties were characterized by the energy dispersive spectroscopy, X-ray diffraction, transmission electron microcopy, atomic force microscopy and nanoindentation. In the Nb–Si–N films, 3 distinct concentration regions have been observed depending on the Si content. Based on the three concentration regions, a three-step model is proposed for the film formation of the Nb–Si–N thin films. This model correlates nanoscale structures with macroscopic properties of the films.

scholarly journals A Simple and Facile Solvothermal Synthesis of Hierarchical PbS Microstars with Multidendritic Arms and Their Optical Properties

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Yong-Fang Li ◽  
Ming Zhang ◽  
Qi-Jing Yang ◽  
Feng-Xian Zhang ◽  
Mei-Qi Zheng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Solvothermal Synthesis ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Practical Applications ◽  
Solar Absorbers ◽  
Transmission Electron ◽  
Ir Photodetectors ◽  
Ft Ir

A simple and facile approach was developed in the solvothermal synthesis of hierarchical PbS microstars with multidendritic arms, which were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) and photoluminescence (PL) spectroscopy. The morphologies of PbS products were strongly determined by the reaction time and temperature, the ratios of the precursors, and the mixed solvent with various components, and thereby their possible formation mechanism was discussed in some detail. The as-prepared PbS crystals displayed a sharp and strong photoluminescent peak at 437 nm at room temperature. It has potential and practical applications in photoluminescence, photovoltaics, IR photodetectors, electroluminescence, and solar absorbers.

Reaction Layer Microstructure of SiC/SiC Joints Brazed by Ag-Cu-Ti Filler Metal

2010 ◽  
Vol 434-435 ◽  
pp. 202-204 ◽  
Author(s):  
Yan Liu ◽  
Zheng Ren Huang ◽  
Xiu Jian Liu
Keyword(s):  
Grain Size ◽  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Reaction Layer ◽  
Filler Metal ◽  
Growth Behavior ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Electronic Probe

Abstract. The reaction layer microstructure of SiC/SiC joints brazed by Ag-Cu-Ti filler metal, including composition, morphology, grain size were investigated by X-ray diffraction, electronic probe microanalysis, transmission electron microscope. An obvious reaction layer composed of TiC and Ti5Si3 was observed at the interface of SiC substrate and filler metal. There is a representative structure of SiC substrate/continuous fine TiC layer /discontinuous coarse Ti5Si3 layer/filler metal in the reaction layer. The continuous TiC layer, composed of about 10 nm roundish grains, is 350 ~ 400 nm thick. Ti5Si3 layer is composed of only one row of Ti5Si3 grains, which disperse with diverse size from 100 ~ 500 nm. Different growth behavior of TiC and Ti5Si3 is the main reason to form this microstructure.

Sign in / Sign up

Export Citation Format

Share Document