Microstructural Studies of the WO3/TiO2 Monolayer Catalyst System Using High Resolution Electron Microscopy

1994 ◽  
Vol 344 ◽  
Author(s):  
A. Burrows ◽  
C. J. Kiely ◽  
R. W. Joyner ◽  
H. Knözinger ◽  
F. Lange
Keyword(s):  
Electron Microscopy ◽  
Surface Roughness ◽  
High Resolution ◽  
Structural Models ◽  
High Resolution Electron Microscopy ◽  
Catalyst System ◽  
Mechanical Mixing ◽  
Chemical Methods ◽  
Resolution Electron ◽  
Microstructural Studies

AbstractWe have characterised the WO3T'iO2 (anatase) catalyst system using High Resolution Electron Microscopy. We will show that the overlayer preserves the surface roughness of titania and consists of 2D-hexagonal clusters that have a definite orientation relationship with the support. The contrast observed from these clusters is discussed in terms of existing structural models. A comparison between traditional chemical methods of preparation and simple mechanical mixing is made to assess the effectiveness of the latter to disperse WO3.

Structural analysis of the surface-layer protein of spirillum serpens by high-resolution electron microscopy

1983 ◽  
Vol 41 ◽  
pp. 738-739
Author(s):  
W. H. Wu ◽  
R. M. Glaeser
Keyword(s):  
Electron Microscopy ◽  
Surface Layer ◽  
Structural Analysis ◽  
High Resolution ◽  
Low Dose ◽  
High Resolution Electron Microscopy ◽  
Optical Diffraction ◽  
Surface Layer Protein ◽  
Morphological Unit ◽  
Resolution Electron

Spirillum serpens possesses a surface layer protein which exhibits a regular hexagonal packing of the morphological subunits. A morphological model of the structure of the protein has been proposed at a resolution of about 25 Å, in which the morphological unit might be described as having the appearance of a flared-out, hollow cylinder with six ÅspokesÅ at the flared end. In order to understand the detailed association of the macromolecules, it is necessary to do a high resolution structural analysis. Large, single layered arrays of the surface layer protein have been obtained for this purpose by means of extensive heating in high CaCl2, a procedure derived from that of Buckmire and Murray. Low dose, low temperature electron microscopy has been applied to the large arrays.As a first step, the samples were negatively stained with neutralized phosphotungstic acid, and the specimens were imaged at 40,000 magnification by use of a high resolution cold stage on a JE0L 100B. Low dose images were recorded with exposures of 7-9 electrons/Å2. The micrographs obtained (Fig. 1) were examined by use of optical diffraction (Fig. 2) to tell what areas were especially well ordered.

Electron microscopy of rabbit FC crystals

1983 ◽  
Vol 41 ◽  
pp. 730-731
Author(s):  
Robert A. Grant ◽  
Laura L. Degn ◽  
Wah Chiu ◽  
John Robinson
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
High Resolution Electron Microscopy ◽  
Molecular Replacement ◽  
X Ray ◽  
X Ray Crystallography ◽  
Resolution Electron ◽  
Replacement Technique ◽  
Hydrated Crystal ◽  
Molecular Structure Analysis

Proteolytic digestion of the immunoglobulin IgG with papain cleaves the molecule into an antigen binding fragment, Fab, and a compliment binding fragment, Fc. Structures of intact immunoglobulin, Fab and Fc from various sources have been solved by X-ray crystallography. Rabbit Fc can be crystallized as thin platelets suitable for high resolution electron microscopy. The structure of rabbit Fc can be expected to be similar to the known structure of human Fc, making it an ideal specimen for comparing the X-ray and electron crystallographic techniques and for the application of the molecular replacement technique to electron crystallography. Thin protein crystals embedded in ice diffract to high resolution. A low resolution image of a frozen, hydrated crystal can be expected to have a better contrast than a glucose embedded crystal due to the larger density difference between protein and ice compared to protein and glucose. For these reasons we are using an ice embedding technique to prepare the rabbit Fc crystals for molecular structure analysis by electron microscopy.

High resolution electron microscopy of lanthanum phosphate crystals

1978 ◽  
Vol 36 (1) ◽  
pp. 274-275
Author(s):  
J. C. Wheatley ◽  
J. M. Cowley
Keyword(s):  
Electron Microscopy ◽  
Catalytic Activity ◽  
High Resolution ◽  
Petroleum Industry ◽  
High Resolution Electron Microscopy ◽  
Lanthanum Phosphate ◽  
Good Catalyst ◽  
Resolution Electron ◽  
Good Catalytic Activity ◽  
Physical And Chemical

Rare-earth phosphates are of particular interest because of their catalytic properties associated with the hydrolysis of many aromatic chlorides in the petroleum industry. Lanthanum phosphates (LaPO4) which have been doped with small amounts of copper have shown increased catalytic activity (1). However the physical and chemical characteristics of the samples leading to good catalytic activity are not known.Many catalysts are amorphous and thus do not easily lend themselves to methods of investigation which would include electron microscopy. However, the LaPO4, crystals are quite suitable samples for high resolution techniques.The samples used were obtained from William L. Kehl of Gulf Research and Development Company. The electron microscopy was carried out on a JEOL JEM-100B which had been modified for high resolution microscopy (2). Standard high resolution techniques were employed. Three different sample types were observed: 669A-1-5-7 (poor catalyst), H-L-2 (good catalyst) and 27-011 (good catalyst).

Possible applications of fraunhofer holography in high resolution electron microscopy

1978 ◽  
Vol 36 (1) ◽  
pp. 222-223 ◽  
Author(s):  
N. Bonnet ◽  
M. Troyon ◽  
P. Gallion
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Transfer Function ◽  
Radiation Damage ◽  
High Resolution Electron Microscopy ◽  
Far Field ◽  
Field Region ◽  
Crystalline Materials ◽  
Resolution Electron ◽  
The Ideal

Two main problems in high resolution electron microscopy are first, the existence of gaps in the transfer function, and then the difficulty to find complex amplitude of the diffracted wawe from registered intensity. The solution of this second problem is in most cases only intended by the realization of several micrographs in different conditions (defocusing distance, illuminating angle, complementary objective apertures…) which can lead to severe problems of contamination or radiation damage for certain specimens.Fraunhofer holography can in principle solve both problems stated above (1,2). The microscope objective is strongly defocused (far-field region) so that the two diffracted beams do not interfere. The ideal transfer function after reconstruction is then unity and the twin image do not overlap on the reconstructed one.We show some applications of the method and results of preliminary tests.Possible application to the study of cavitiesSmall voids (or gas-filled bubbles) created by irradiation in crystalline materials can be observed near the Scherzer focus, but it is then difficult to extract other informations than the approximated size.

The observation of solutions in Ni3Nb

1988 ◽  
Vol 46 ◽  
pp. 540-541
Author(s):  
Z.M. Wang ◽  
J.P. Zhang
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Phase Modulation ◽  
High Resolution Electron Microscopy ◽  
Antiphase Domain ◽  
Boundary Area ◽  
Matrix Type ◽  
Resolution Electron ◽  
Domain Boundaries ◽  
Kontorova Model

High resolution electron microscopy reveals that antiphase domain boundaries in β-Ni3Nb have a hexagonal unit cell with lattice parameters ah=aβ and ch=bβ, where aβ and bβ are of the orthogonal β matrix. (See Figure 1.) Some of these boundaries can creep “upstairs” leaving an incoherent area, as shown in region P. When the stepped boundaries meet each other, they do not lose their own character. Our consideration in this work is to estimate the influnce of the natural misfit δ{(ab-aβ)/aβ≠0}. Defining the displacement field at the boundary as a phase modulation Φ(x), following the Frenkel-Kontorova model [2], we consider the boundary area to be made up of a two unit chain, the upper portion of which can move and the lower portion of the β matrix type, assumed to be fixed. (See the schematic pattern in Figure 2(a)).

Atomic structure imaging of the Si/SiO2 interface with high-resolution electron microscopy

1986 ◽  
Vol 44 ◽  
pp. 390-391
Author(s):  
J.L. Batstone ◽  
J.M. Gibson ◽  
Alice.E. White ◽  
K.T. Short
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Atomic Structure ◽  
High Resolution Electron Microscopy ◽  
Medium Voltage ◽  
Voltage Electron ◽  
Resolution Electron ◽  
Structural Image ◽  
Electron Microscopes ◽  
Point To Point

High resolution electron microscopy (HREM) is a powerful tool for the determination of interface atomic structure. With the previous generation of HREM's of point-to-point resolution (rpp) >2.5Å, imaging of semiconductors in only <110> directions was possible. Useful imaging of other important zone axes became available with the advent of high voltage, high resolution microscopes with rpp <1.8Å, leading to a study of the NiSi2 interface. More recently, it was shown that images in <100>, <111> and <112> directions are easily obtainable from Si in the new medium voltage electron microscopes. We report here the examination of the important Si/Si02 interface with the use of a JEOL 4000EX HREM with rpp <1.8Å, in a <100> orientation. This represents a true structural image of this interface.

High-resolution electron microscopy of nanostructured materials

1995 ◽  
Vol 53 ◽  
pp. 172-173
Author(s):  
M. José-Yacamán
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Grain Boundaries ◽  
Nanostructured Materials ◽  
High Resolution Electron Microscopy ◽  
Hrem Image ◽  
Small Particles ◽  
Resolution Electron ◽  
Nanophase Materials

Electron microscopy is a fundamental tool in materials characterization. In the case of nanostructured materials we are looking for features with a size in the nanometer range. Therefore often the conventional TEM techniques are not enough for characterization of nanophases. High Resolution Electron Microscopy (HREM), is a key technique in order to characterize those materials with a resolution of ~ 1.7A. High resolution studies of metallic nanostructured materials has been also reported in the literature. It is concluded that boundaries in nanophase materials are similar in structure to the regular grain boundaries. That work therefore did not confirm the early hipothesis on the field that grain boundaries in nanostructured materials have a special behavior. We will show in this paper that by a combination of HREM image processing, and image calculations, it is possible to prove that small particles and coalesced grains have a significant surface roughness, as well as large internal strain.

Time-resolved high-resolution electron microscopy of structural stability in mgo clusters

1996 ◽  
Vol 54 ◽  
pp. 672-673
Author(s):  
T. Kizuka ◽  
N. Tanaka
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Magnesium Oxide ◽  
Structural Stability ◽  
High Resolution Electron Microscopy ◽  
Video Tape ◽  
Solid State Physics ◽  
Time Resolved ◽  
Resolution Electron ◽  
Structural And Functional Properties

Structure and stability of atomic clusters have been studied by time-resolved high-resolution electron microscopy (TRHREM). Typical examples are observations of structural fluctuation in gold (Au) clusters supported on silicon oxide films, graphtized carbon films and magnesium oxide (MgO) films. All the observations have been performed on the clusters consisted of single metal element. Structural stability of ceramics clusters, such as metal-oxide, metal-nitride and metal-carbide clusters, has not been observed by TRHREM although the clusters show anomalous structural and functional properties concerning to solid state physics and materials science.In the present study, the behavior of ceramic, magnesium oxide (MgO) clusters is for the first time observed by TRHREM at 1/60 s time resolution and at atomic resolution down to 0.2 nm.MgO and gold were subsequently deposited on sodium chloride (001) substrates. The specimens, single crystalline MgO films on which Au particles were dispersed were separated in distilled water and observed by using a 200-kV high-resolution electron microscope (JEOL, JEM2010) equipped with a high sensitive TV camera and a video tape recorder system.

High Resolution Transmission Electron Microscopy of an automobile catalytic converter

1990 ◽  
Vol 48 (4) ◽  
pp. 242-243
Author(s):  
Jan-Olle Malm ◽  
Jan-Olov Bovin
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Catalytic Converter ◽  
Active Material ◽  
Image Intensifier ◽  
High Resolution Electron Microscopy ◽  
Detailed Knowledge ◽  
Transmission Electron ◽  
Resolution Electron ◽  
Atomic Surface

Understanding of catalytic processes requires detailed knowledge of the catalyst. As heterogeneous catalysis is a surface phenomena the understanding of the atomic surface structure of both the active material and the support material is of utmost importance. This work is a high resolution electron microscopy (HREM) study of different phases found in a used automobile catalytic converter.The high resolution micrographs were obtained with a JEM-4000EX working with a structural resolution better than 0.17 nm and equipped with a Gatan 622 TV-camera with an image intensifier. Some work (e.g. EDS-analysis and diffraction) was done with a JEM-2000FX equipped with a Link AN10000 EDX spectrometer. The catalytic converter in this study has been used under normal driving conditions for several years and has also been poisoned by using leaded fuel. To prepare the sample, parts of the monolith were crushed, dispersed in methanol and a drop of the dispersion was placed on the holey carbon grid.

HRTEM simulation of interfacial structure in amorphous multilayers

1989 ◽  
Vol 47 ◽  
pp. 466-467
Author(s):  
Margaret L. Sattler ◽  
Michael A. O'Keefe
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Cross Section ◽  
High Resolution Electron Microscopy ◽  
Interfacial Structure ◽  
Multilayer Sample ◽  
Resolution Electron ◽  
Multilayered Materials ◽  
Simulated Images

Multilayered materials have been fabricated with such high perfection that individual layers having two atoms deep are possible. Characterization of the interfaces between these multilayers is achieved by high resolution electron microscopy and Figure 1a shows the cross-section of one type of multilayer. The production of such an image with atomically smooth interfaces depends upon certain factors which are not always reliable. For example, diffusion at the interface may produce complex interlayers which are important to the properties of the multilayers but which are difficult to observe. Similarly, anomalous conditions of imaging or of fabrication may occur which produce images having similar traits as the diffusion case above, e.g., imaging on a tilted/bent multilayer sample (Figure 1b) or deposition upon an unaligned substrate (Figure 1c). It is the purpose of this study to simulate the image of the perfect multilayer interface and to compare with simulated images having these anomalies.

Sign in / Sign up

Export Citation Format

Share Document