Fine Structure of Sputtered Ni/Ti Multilayered Thin Films Studied by HREM

1994 ◽  
Vol 343 ◽  
Author(s):  
M. J. Casanove ◽  
E. Snoeck ◽  
C. Roucau ◽  
J. L. Hutchison ◽  
Z. Jiang ◽  
...  
Keyword(s):  
Thin Films ◽  
Fine Structure ◽  
Growth Direction ◽  
Cross Sectional ◽  
Neutron Optics ◽  
Transmission Electron ◽  
Amorphous Zone ◽  
Sharp Interfaces ◽  
Multilayered Thin Films ◽  
Neutron Guides

ABSTRACTNi/Ti multilayered thin films can be efficient neutron guides and are therefore of great interest in neutron optics. Ni/Ti and NiC/Ti multilayers with various layer thicknesses were fabricated by magnetron sputtering and characterized by high resolution transmission electron microscopy (TEM). The TEM studies, performed on cross-sectional specimens, revealed that both kinds of layers were textured and snowed coherence in the growth direction. The presence of a 2 nra thick amorphous zone at the Ni/Ti interface in the carbon free thin films was also confirmed. On the contrary, sharp interfaces were obtained in NiC/Ti multilayers. The fine structure of the different layers will also be reported.

Characterization of reactive phase formation in sputter-deposited Ni/Al multilayer thin films using TEM

1996 ◽  
Vol 54 ◽  
pp. 1000-1001
Author(s):  
G. Lucadamo ◽  
K. Barmak ◽  
C. Michaelsen
Keyword(s):  
Thin Films ◽  
Phase Formation ◽  
Dark Field ◽  
Nickel Layer ◽  
Multilayer Thin Films ◽  
Cross Sectional ◽  
Dark Field Imaging ◽  
Transmission Electron ◽  
Sputter Deposited ◽  
Constant Heating

The subject of reactive phase formation in multilayer thin films of varying periodicity has stimulated much research over the past few years. Recent studies have sought to understand the reactions that occur during the annealing of Ni/Al multilayers. Dark field imaging from transmission electron microscopy (TEM) studies in conjunction with in situ x-ray diffraction measurements, and calorimetry experiments (isothermal and constant heating rate), have yielded new insights into the sequence of phases that occur during annealing and the evolution of their microstructure.In this paper we report on reactive phase formation in sputter-deposited lNi:3Al multilayer thin films with a periodicity A (the combined thickness of an aluminum and nickel layer) from 2.5 to 320 nm. A cross-sectional TEM micrograph of an as-deposited film with a periodicity of 10 nm is shown in figure 1. This image shows diffraction contrast from the Ni grains and occasionally from the Al grains in their respective layers.

Observations of Domain Structure at Initial Growth Stage of PbTiO3 Thin Films Grown by Mocvd

1999 ◽  
Vol 596 ◽  
Author(s):  
H. Fujisawa ◽  
M. Shimizu ◽  
H. Niu ◽  
K. Honda ◽  
S Ohtani
Keyword(s):  
Thin Films ◽  
Domain Structure ◽  
Growth Stage ◽  
Domain Walls ◽  
Chemical Vapor ◽  
Initial Growth ◽  
Continuous Film ◽  
Cross Sectional ◽  
Initial Growth Stage ◽  
Transmission Electron

AbstractDomain structure and growth mechanism of PbTiO3 thin films were investigated using a transmission electron microscopy(TEM) from the viewpoint of size effects. At initial growth stage of (111)-oriented PbTiO3 films prepared by metalorganic chemical vapor deposition(MOCVD), triangle-shaped islands were grown on Pt(111)/SiO2/Si before becoming a continuous film. Triangular islands grew gradually in a lateral dimension. This means that PbTiO3 films grew two-dimensionally at initial growth stage. In cross-sectional TEM photomicrographs, (101)-twin boundaries (90° domain walls) and inclination of {110} or {101}-plane were observed in PbTiO3 islands. This result indicates that such small PbTiO3 islands have a tetragonal structure and could have spontaneous polarization. The minimum island which had 90° domain walls was 10nm high and 18nm wide.

Microstresses in Molybdenum Nitride Thin Films Deposited by Reactive DC Magnetron Sputtering

2005 ◽  
Vol 490-491 ◽  
pp. 589-594 ◽  
Author(s):  
Yao Gen Shen
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Film Growth ◽  
Nitrogen Addition ◽  
Molybdenum Nitride ◽  
Dc Magnetron Sputtering ◽  
Cross Sectional ◽  
Dense Microstructure ◽  
Transmission Electron ◽  
Complete Relaxation

Thin films of molybdenum nitride (MoNx with 0≤x≤0.35) were deposited on Si(100) at room temperature using reactive DC magnetron sputtering. The residual stress of films was measured as a function of sputtering pressure, nitrogen incorporation, and annealing temperature by wafer curvature-based technique. It was found that the stress of the films was strongly related to their microstructure, which depended mainly on the incorporation of nitrogen in the films. The film stresses without nitrogen addition strongly depended on the argon pressure and changed from highly compressive to highly tensile in a relatively narrow pressure range of 0.8-1.6 Pa. For pressures exceeding ~5.3 Pa, the stress in the film was nearly zero. Cross-sectional transmission electron microscopy indicated that the compressively stressed films contained a dense microstructure without any columns, while the films having tensile stress had a very columnar microstructure. High sputtering-gas pressure conditions yielded dendritic-like film growth, resulting in complete relaxation of the residual tensile stresses. It was also found that the asdeposited film was poorly ordered in structure. When the film was heated at ~775 K, crystallization occurred and the stress of the film drastically changed from –0.75 to 1.65 GPa. The stress development mechanism may be due to volumetric shrinkage of the film during crystallization.

In-plane Molecular Alignment in Thin Films of Pentacene Grown by Solution Casting and Performance of Thin Film Transistors

2007 ◽  
Vol 1003 ◽  
Author(s):  
Takashi Minakata ◽  
Yutaka Nastume
Keyword(s):  
Thin Films ◽  
Single Crystal ◽  
Crystalline Structure ◽  
Grazing Incidence ◽  
Growth Direction ◽  
Molecular Alignment ◽  
Patterned Substrate ◽  
Polarized Microscopy ◽  
Transmission Electron ◽  
And Performance

AbstractWe have fabricated solution-processed thin films of pentacene by casting solution on a substrate and vaporizing solvent. The films with large oriented platelet domains were obtained by directionally grown condition. Molecular alignment in the directionally grown grains has been studied by several kinds of structural analysis. Oriented domains with the width of several hundreds microns and the length in an order of cm of the films were confirmed by polarized microscopy. In-plane crystalline structure of the domain has been studied by grazing incidence X-ray diffraction (GIXD) and strong anisotropy of in-plane crystalline structure was confirmed. Crystalline growth direction of the film was determined to be b-axis from both transmission electron diffraction and GIXD. Thin films transistors (TFTs) with directionally oriented domains of the films were fabricated on electrode patterned substrate. The observed maximum carrier mobility of 2.7 cm2/Vs was comparable to that of single crystal, which indicated that the quality of the film was almost identical with the single crystal. Correlation between FET performance and growth direction was studied and preferred performance of TFTs with the film grown perpendicularly to the channel was observed.

Characterization of pulsed laser deposited MoS2 by transmission electron microscopy

1993 ◽  
Vol 8 (11) ◽  
pp. 2933-2941 ◽  
Author(s):  
S.D. Walek ◽  
M.S. Donley ◽  
J.S. Zabinski ◽  
V.J. Dyhouse
Keyword(s):  
Electron Microscopy ◽  
Thin Films ◽  
Transmission Electron Microscopy ◽  
Solid Phase ◽  
Analytical Electron Microscopy ◽  
Pulsed Laser ◽  
Cross Sectional ◽  
Aerospace Applications ◽  
Transmission Electron ◽  
Novel Method

Molybdenum disulfide is a technologically important solid phase lubricant for vacuum and aerospace applications. Pulsed laser deposition of MoS2 is a novel method for producing fully dense, stoichiometric thin films and is a promising technique for controlling the crystallographic orientation of the films. Transmission electron microscopy (TEM) of self-supporting thin films and cross-sectional TEM samples was used to study the crystallography and microstructure of pulsed laser deposited films of MoS2. Films deposited at room temperature were found to be amorphous. Films deposited at 300 °C were nanocrystalline and had the basal planes oriented predominately parallel to the substrate within the first 12–15 nm of the substrate with an abrupt upturn into a perpendicular (edge) orientation farther from the substrate. Spherically shaped particles incorporated in the films from the PLD process were found to be single crystalline, randomly oriented, and less than about 0.1 μm in diameter. A few of these particles, observed in cross section, had flattened bottoms, indicating that they were molten when they arrived at the surface of the growing film. Analytical electron microscopy (AEM) was used to study the chemistry of the films. The x-ray microanalysis results showed that the films have the stoichiometry of cleaved single crystal MoS2 standards.

Growth of a-plane ZnO Thin Films on r-plane Sapphire by Plasma-assisted MBE

2005 ◽  
Vol 891 ◽  
Author(s):  
Junqing Q. Xie ◽  
J. W. Dong ◽  
A. Osinsky ◽  
P. P. Chow ◽  
Y. W. Heo ◽  
...  
Keyword(s):  
Thin Films ◽  
Lattice Mismatch ◽  
Defect Density ◽  
Zno Thin Films ◽  
Rf Plasma ◽  
Misfit Dislocations ◽  
Epitaxial Relationship ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Small Lattice

ABSTRACTZnO thin films have been epitaxially grown on r-plane sapphire by RF-plasma-assisted molecular beam epitaxy. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies indicate that the epitaxial relationship between ZnO and r-plane sapphire is (1120)ZnO // (1102)sapphire and [0001]ZnO // [1101]sapphire. Atomic force microscopy measurements reveal islands extended along the sapphire [1101] direction. XRD omega rocking curves for the ZnO (1120) reflection measured either parallel or perpendicular to the island direction suggest the defect density anisotropy along these directions. Due to the small lattice mismatch along the ZnO [0001] direction, few misfit dislocations were observed at the ZnO/Al2O3 interface in the high-resolution cross-sectional TEM image with the zone axis along the ZnO [1100] direction.

Sign in / Sign up

Export Citation Format

Share Document