scholarly journals Tensile and Stress-Rupture Behavior of Hafnium Carbide Dispersed Molybdenum and Tungsten Base Alloy Wires

1993 ◽  
Vol 322 ◽  
Author(s):  
H.M. Yun ◽  
R.H. Titran
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rupture Strength ◽  
Base Alloy ◽  
Stress Rupture ◽  
Rate Sensitivity ◽  
Tungsten Alloy ◽  
Rate Dependency ◽  
Hafnium Carbide ◽  
Stress Rupture Strength

AbstractThe tensile strain rate sensitivity and the stress-rupture strength of Mo-base and W-base alloy wires, 380 µm in diameter, were determined over the temperature range from 1200 to 1600 K. Three molybdenum alloy wires; Mo + 1.1 wt% hafnium carbide (MoHfC), Mo + 25 wt% W + 1.1 wt% hafnium carbide (MoHfC+25W) and Mo + 45 wt% W + 1.1 wt% hafnium carbide (MoHfC+45W), and a W + 0.4 wt% hafnium carbide (WHfC) tungsten alloy wire were evaluated.The tensile strength of all wires studied was found to have a positive strain rate sensitivity. The strain rate dependency increased with increasing temperature and is associated with grain broadening of the initial fibrous structures. The hafnium carbide dispersed W-base and Mo-base alloys have superior tensile and stress-rupture properties than those without HfC. On a density compensated basis the MoHfC wires exhibit superior tensile and stress-rupture strengths to the WHfC wires up to approximately 1400 K. Addition of tungsten in the Mo-alloy wires was found to increase the long-term stress-rupture strength at temperatures above 1400 K.

Mechanical Anisotropy and Strain Rate Dependency Behavior of Ti6Al4V Produced Using E-Beam Additive Fabrication

2014 ◽  
Vol 136 (3) ◽  
Author(s):  
Leila Ladani ◽  
Jafar Razmi ◽  
Soud Farhan Choudhury
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Mechanical Behavior ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Mechanical Anisotropy ◽  
Rate Dependency ◽  
Out Of Plane ◽  
Degree Of Anisotropy ◽  
Strain Rate Dependency

Anisotropic mechanical behavior is an inherent characteristic of parts produced using additive manufacturing (AM) techniques in which parts are built layer by layer. It is expected that in-plane and out-of-plane properties be different in these parts. E-beam fabrication is not an exception to this. It is, however, desirable to keep this degree of anisotropy to a minimum level and be able to produce parts with comparable mechanical strength in both in-plane and out-of-plane directions. In this manuscript, this degree of anisotropy is investigated for Ti6Al4V parts produced using this technique through tensile testing of parts built in different orientations. Mechanical characteristics such as Young's modulus, yield strength (YS), ultimate tensile strength (UTS), and ductility are evaluated. The strain rate effect on mechanical behavior, namely, strength and ductility, is also investigated by testing the material at a range of strain rates from 10−2 to 10−4 s−1. Local mechanical properties were extracted using nanoindentation technique and compared against global values (average values obtained by tensile tests). Although the properties obtained in this experiment were comparable with literature findings, test results showed that in-plane properties, elastic modulus, YS, and UTS are significantly higher than out-of-plane properties. This could be an indication of defects in between layers or imperfect bonding of the layers. Strong positive strain rate sensitivity was observed in out-of-plane direction. The strain rate sensitivity evaluation did not show strain rate dependency for in-plane directions. Local mechanical properties obtained through nanoindentation confirmed the findings of tensile test and also showed variation of properties caused by geometry.

scholarly journals Programming Strain Rate Dependency into Mechanical Metamaterials

2021 ◽  
Vol 250 ◽  
pp. 02031
Author(s):  
Sankalp Patil ◽  
Georg Ganzenmüller
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Base Material ◽  
Rate Sensitivity ◽  
Dissipated Energy ◽  
Friction Unit ◽  
Geometrical Parameters ◽  
Rate Dependency ◽  
Rate Dependent ◽  
Mechanical Metamaterials

This work presents an approach to introduce significant strain rate sensitivity into metallic metamaterials that are manufactured via additive manufacturing, where the base material employed will typically have a weak strain rate sensitivity. Here, we employ friction between the rough surfaces as the strain-rate dependent mechanism, whose magnitude is tunable by optimizing the geometry. The design along with the preliminary simulation results of the friction unit cell is presented. This work will quantify the effects of geometrical parameters on the dissipated energy.

scholarly journals Strain rate sensitivity of the aluminium-magnesium-scandium alloy - Scalmalloy®

2021 ◽  
Vol 250 ◽  
pp. 05014
Author(s):  
Puneeth Jakkula ◽  
Georg Ganzenmüller ◽  
Florian Gutmann ◽  
Stefan Hiermaier
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Testing Machine ◽  
Rate Sensitivity ◽  
Tensile Tests ◽  
Image Correlation ◽  
Strain Rates ◽  
Rate Dependency ◽  
Strain Rate Dependency ◽  
Scandium Alloy

This work investigates the strain rate sensitivity of the aluminiummagnesium-scandium alloy Scalmalloy, which is used extensively for additive manufacturing of lightweight structures. This high strength aluminium alloy combines very good weldability, machinability and mechanical strength: it can be heat-treated to reach nominal ultimate tensile strengths in excess of 500 MPa. We report tensile tests at strain rates ranging from 10−3 /s to 103 /s at room temperature. It is well known that Al-Mg alloys exhibit a negative strain rate dependency in combination with serrated flow caused by the Portevin-Le Chatelier effect, which describes the interaction of Mg solutes with dislocation propagations. In contrast, in Al-Sc alloys, the flow stress increases with increasing strain rate and displays positive strain rate dependency. Additionally, the presence of Sc in the form of Al3-Sc provides a fine-grained microstructure which allows higher tensile and fatigue strength. This research shows how these combined effects interact in the case of Scalmalloy, which contains both Mg and Sc. Tests are performed at quasi-static, intermediate and high strain rates with a servohydraulic testing machine and a Split-Hopkinson tension bar. Local specimen strain was performed using 2D Digital Image Correlation.

THERMO-SPAN ALLOY

Alloy Digest ◽  
1994 ◽  
Vol 43 (2) ◽  
Keyword(s):  
Physical Properties ◽  
Tensile Properties ◽  
Fatigue Resistance ◽  
Thermal Fatigue ◽  
Rupture Strength ◽  
Stress Rupture ◽  
Heat Treating ◽  
Thermal Fatigue Resistance ◽  
Stress Rupture Strength

Abstract THERMO-SPAN ALLOY is a precipitation-hardenable superalloy with a low coefficient of expansion combined with tensile and stress-rupture strength. Thermal fatigue resistance is inherent. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on forming and heat treating. Filing Code: FE-105. Producer or source: Carpenter.

scholarly journals Negative Strain Rate Sensitivity Induced by Structure Heterogeneity in Zr64.13Cu15.75Ni10.12Al10 Bulk Metallic Glass

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 339
Author(s):  
Xiang Wang ◽  
Zhi Qiang Ren ◽  
Wei Xiong ◽  
Si Nan Liu ◽  
Ying Liu ◽  
...  
Keyword(s):  
Metallic Glass ◽  
Strain Rate ◽  
Bulk Metallic Glass ◽  
Strain Rate Sensitivity ◽  
Critical Role ◽  
Rate Sensitivity ◽  
Confined Compression ◽  
Negative Strain Rate Sensitivity ◽  
Cast Specimen ◽  
Structure Heterogeneity

The negative strain rate sensitivity (SRS) of metallic glasses is frequently observed. However, the physical essence involved is still not well understood. In the present work, small-angle X-ray scattering (SAXS) and high-resolution transmission electron microscopy (HRTEM) reveal the strong structure heterogeneity at nanometer and tens of nanometer scales, respectively, in bulk metallic glass (BMG) Zr64.13Cu15.75Ni10.12Al10 subjected to fully confined compression processing. A transition of SRS of stress, from 0.012 in the as-cast specimen to −0.005 in compression processed specimen, was observed through nanoindentation. A qualitative formulation clarifies the critical role of internal stress induced by structural heterogeneity in this transition. It reveals the physical origin of this negative SRS frequently reported in structurally heterogeneous BMG alloys and its composites.

Strain rate sensitivity of a 1.5 GPa nanotwinned steel

2021 ◽  
Author(s):  
R.D. Liu ◽  
Y.Z. Li ◽  
L. Lin ◽  
C.P. Huang ◽  
Z.H. Cao ◽  
...  
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity

scholarly journals The Strain Rate Sensitivity and Creep Behavior for the Tripler Plane of Potassium Dihydrogen Phosphate Crystal by Nanoindentation

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 369
Author(s):  
Jianhui Mao ◽  
Wenjun Liu ◽  
Dongfang Li ◽  
Chenkai Zhang ◽  
Yi Ma
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Creep Deformation ◽  
Potassium Dihydrogen Phosphate ◽  
Rate Sensitivity ◽  
Dislocation Nucleation ◽  
Machining Process ◽  
Dihydrogen Phosphate ◽  
Potassium Dihydrogen ◽  
Kdp Crystals

As an excellent multifunctional single crystal, potassium dihydrogen phosphate (KDP) is a well-known, difficult-to-process material for its soft-brittle and deliquescent nature. The surface mechanical properties are critical to the machining process; however, the characteristics of deformation behavior for KDP crystals have not been well studied. In this work, the strain rate effect on hardness was investigated on the mechanically polished tripler plane of a KDP crystal relying on nanoindentation technology. By increasing the strain rate from 0.001 to 0.1 s−1, hardness increased from 1.67 to 2.07 GPa. Hence, the strain rate sensitivity was determined as 0.053, and the activation volume of dislocation nucleation was 169 Å3. Based on the constant load-holding method, creep deformation was studied at various holding depths at room temperature. Under the spherical tip, creep deformation could be greatly enhanced with increasing holding depth, which was mainly due to the enlarged holding strain. Under the self-similar Berkovich indenter, creep strain could be reduced at a deeper location. Such an indentation size effect on creep deformation was firstly reported for KDP crystals. The strain rate sensitivity of the steady-state creep flow was estimated, and the creep mechanism was qualitatively discussed.

Sign in / Sign up

Export Citation Format

Share Document