Localized Influence of Solute on the Stacking Fault Energy of Dilute Al-Based Solid Solutions

1993 ◽  
Vol 319 ◽  
Author(s):  
C. Lane Rohrer
Keyword(s):  
Solid Solutions ◽  
Partial Dislocation ◽  
Binary Systems ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Dislocation Dipole ◽  
Partial Dislocations ◽  
Pure Metals ◽  
Small Clusters ◽  
Dislocation Spacing

AbstractThe stacking fault energy (SFE) is widely used to classify the mechanical behavior of pure metals. In alloys, however, the experimentally observed SFE is strongly influenced by localized solute effects. To further understand these effects on dislocation structure and on the observed SFE, solute segregation to an extended edge dislocation dipole, delineating two stacking faults, was studied in dilute Al:Cu, Al:Ag, and Al:Cu, Ag solid solutions. Cu and Ag were chosen to isolate solute size and modulus effects, Cu being smaller than Al, while Ag and Al are essentially the same size. Atomistic Monte Carlo results showed little change in the partial dislocation spacing in the binary systems as compared to the spacing in pure Al, even though Cu was observed to segregate to the compressive regions of the dislocation dipoles, forming widespread atmospheres, while Ag formed randomly distributed Ag-rich zones. However, in ternary Al:Cu,Ag simulations, the Ag apparently inhibited the Cu from distributing across the width of the extended dislocations, both Ag and Cu forming small clusters near or on the partial dislocations which increased the partial dislocation spacing. Results will be discussed in light of interpretations of experimental SFE determinations, emphasizing the importance of the localized solute distribution on the SFE.

Stacking fault energy in austenitic steels determined by usingin situX-ray diffraction during bending

2014 ◽  
Vol 47 (3) ◽  
pp. 936-947 ◽  
Author(s):  
D. Rafaja ◽  
C. Krbetschek ◽  
C. Ullrich ◽  
S. Martin
Keyword(s):  
Critical Stress ◽  
Partial Dislocation ◽  
Stacking Faults ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Austenitic Steels ◽  
X Ray Diffraction ◽  
X Ray ◽  
Partial Dislocations

A method is presented which determines the stacking fault energy in face-centred cubic materials from the critical stress that is inducedviasample bending in the early stages of plastic deformation. The critical stress is gauged byin situX-ray diffraction. This method utilizes the results of Byun's consideration of the stress dependence of the partial dislocation separation [Byun (2003).Acta Mater.51, 3063–3071]. Byun showed that the separation distance of the partial dislocations increases rapidly when the critical stress is reached and that the critical stress needed for the rapid separation of the partial dislocations is directly proportional to the stacking fault energy. In the approach presented here, the partial dislocation separation and the corresponding triggering stress are monitored by usingin situX-ray diffraction during sample bending. Furthermore, thein situX-ray diffraction measurement checks the possible interactions between stacking faults present on equivalent lattice planes and the interactions of the stacking faults with other microstructure defects. The capability of the proposed method was tested on highly alloyed austenitic steels containing chromium (∼16 wt%), manganese (∼7 wt%) and nickel as the main alloying elements. For the steels containing 5.9 and 3.7 wt% Ni, stacking fault energies of 17.5 ± 1.4 and 8.1 ± 0.9 mJ m−2were obtained, respectively.

On effects of non-systematic reflections on weak-beam images of partial dislocations

1991 ◽  
Vol 49 ◽  
pp. 688-689
Author(s):  
K. Z. Botros ◽  
S. S. Sheinin
Keyword(s):  
High Precision ◽  
Stacking Fault ◽  
Important Application ◽  
Stacking Fault Energy ◽  
Sharp Peak ◽  
Weak Beam ◽  
Partial Dislocations ◽  
Deviation Parameter ◽  
Beam Diffraction

The main features of weak beam images of dislocations were first described by Cockayne et al. using calculations of intensity profiles based on the kinematical and two beam dynamical theories. The feature of weak beam images which is of particular interest in this investigation is that intensity profiles exhibit a sharp peak located at a position very close to the position of the dislocation in the crystal. This property of weak beam images of dislocations has an important application in the determination of stacking fault energy of crystals. This can easily be done since the separation of the partial dislocations bounding a stacking fault ribbon can be measured with high precision, assuming of course that the weak beam relationship between the positions of the image and the dislocation is valid. In order to carry out measurements such as these in practice the specimen must be tilted to "good" weak beam diffraction conditions, which implies utilizing high values of the deviation parameter Sg.

Dislocations and stacking faults in stainless steel

1957 ◽  
Vol 240 (1223) ◽  
pp. 524-538 ◽  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Stainless Steel ◽  
Grain Boundaries ◽  
Stacking Faults ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Thin Sections ◽  
Partial Dislocations ◽  
Transmission Electron

Further experiments by transmission electron microscopy on thin sections of stainless steel deformed by small amounts have enabled extended dislocations to be observed directly. The arrangement and motion of whole and partial dislocations have been followed in detail. Many of the dislocations are found to have piled up against grain boundaries. Other observations include the formation of wide stacking faults, the interaction of dislocations with twin boundaries, and the formation of dislocations at thin edges of the foils. An estimate is made of the stacking-fault energy from a consideration of the stresses present, and the properties of the dislocations are found to be in agreement with those expected from a metal of low stacking-fault energy.

scholarly journals The effect of stacking fault energy on acoustic emission in pure metals with face-centered crystal lattice

2017 ◽  
Vol 7 (4) ◽  
pp. 437-441 ◽  
Author(s):  
A. V. Danyuk ◽  
D. L. Merson ◽  
I. S. Yasnikov ◽  
E. A. Agletdinov ◽  
M. A. Afanasiev ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Crystal Lattice ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Pure Metals ◽  
Face Centered

Stacking Faults in Crystals

1968 ◽  
Vol 26 ◽  
pp. 250-251
Author(s):  
P. C. J. Gallagher
Keyword(s):  
Stacking Faults ◽  
Elastic Equilibrium ◽  
Stacking Fault ◽  
Stacking Fault Energy ◽  
Major Influence ◽  
Face Centered Cubic ◽  
Degree Of Dissociation ◽  
Partial Dislocations ◽  
Layer Structures ◽  
Face Centered

Stacking faults are an important substructural feature of many materials, and have been widely studied in layer structures (e.g. talc) and in crystals with hexagonal and face centered cubic structure. Particular emphasis has been placed on the study of faulted defects in f.c.c. alloys, since the width of the band of fault between dissociated partial dislocations has a major influence on mechanical properties.Under conditions of elastic equilibrium the degree of dissociation reflects the balance of the repulsive force between the partials bounding the fault, and the attractive force associated with the need to minimize the energy arising from the misfits in stacking sequence. Examples of two of the faulted defects which can be used to determine this stacking fault energy, Υ, are shown in Fig. 1. Intrinsically faulted extended nodes (as at A) have been widely used to determine Υ, and examples will be shown in several Cu and Ag base alloys of differing stacking fault energy. The defect at B contains both extrinsic and intrinsic faulting, and readily enables determination of both extrinsic and intrinsic fault energies.

Sign in / Sign up

Export Citation Format

Share Document