Synthesis of (SIC)3N4 Films by Ion Implantation

1993 ◽  
Vol 316 ◽  
Author(s):  
C. Uslu ◽  
D. H. Lee ◽  
Y. Berta ◽  
B. Park ◽  
N. N. Thadhani ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Amorphous Layer ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Nitrogen Implantation ◽  
Transmission Electron ◽  
Position Sensitive ◽  
Nitrogen Ions ◽  
Substrate Temperatures ◽  
New Phase

ABSTRACTWe have investigated the synthesis of carbon-silicon-nitride compounds by ion implantation. In these experiments, 100 keV nitrogen ions were implanted into polycrystalline β-SiC (cubic phase) at various substrate temperatures and ion doses. These thin films were characterized in detail by x-ray diffraction with a position-sensitive detector, transmission electron microscopy with chemical analysis, and Rutherford backscattering spectroscopy. The as-implanted samples show a buried amorphous layer at a depth of 170 nm. The peak concentration of nitrogen saturates at approximately 45 at. % with doses above ~9.0×1017 N/cm2 at 860°C. These results suggest formation of a new phase by nitrogen implantation into β-SiC.

Synthesis and Characterization of A Metastable (SiC)aN4 Phase

1994 ◽  
Vol 354 ◽  
Author(s):  
C. Uslu ◽  
B. Park ◽  
D. B. Poker
Keyword(s):  
Cubic Phase ◽  
High Dose ◽  
Sensitive Detector ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Transmission Electron ◽  
Position Sensitive ◽  
New Phase

AbstractA metastable C-Si-N compound has been synthesized by high dose N+ implantation into polycrystalline /8-SiC (cubic phase). The thin films formed upon 100 keV implantations were characterized with respect to various ion doses and target temperatures. X-ray diffraction with a position-sensitive detector and cross-sectional transmission electron microscopy revealed that the as-implanted surfaces contained ∼0.15 jttm thick continuously-buried amorphous layers. Rutherford backscattering spectroscopy showed that the peak concentration of nitrogen saturated up to approximately 54 at. % with increasing doses, suggesting a new phase formation.

scholarly journals Dual Electrochemical Treatments to Improve Properties of Ti6Al4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2479
Author(s):  
Stefano Rossi ◽  
Luciana Volgare ◽  
Carine Perrin-Pellegrino ◽  
Carine Chassigneux ◽  
Erick Dousset ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Combined Treatment ◽  
Amorphous Film ◽  
Amorphous Layer ◽  
Good Alternative ◽  
Surface Treatments ◽  
Ex Situ ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Fluid Environment

Surface treatments are considered as a good alternative to increase biocompatibility and the lifetime of Ti-based alloys used for implants in the human body. The present research reports the comparison of bare and modified Ti6Al4V substrates on hydrophilicity and corrosion resistance properties in body fluid environment at 37 °C. Several surface treatments were conducted separately to obtain either a porous oxide layer using nanostructuration (N) in ethylene glycol containing fluoride solution, or bulk oxide thin films through heat treatment at 450 °C for 3 h (HT), or electrochemical oxidation at 1 V for 3 h (EO), as well as combined treatments (N-HT and N-EO). In-situ X-ray diffraction and ex-situ transmission electron microscopy have shown that heat treatment gave first rise to the formation of a 30 nm thick amorphous layer which crystallized in rutile around 620 °C. Electrochemical oxidations gave rise to a 10 nm thick amorphous film on the top of the surface (EO) or below the amorphous nanotube layer (N-EO). Dual treated samples presented similar results with a more stable behavior for N-EO. Finally, for both corrosion and hydrophilicity points of view, the new combined treatment to get a total amorphous N-EO sample seems to be the best and even better than the partially crystallized N-HT sample.

Optical properties of anatase TiO2 films modified by N ion implantation

2012 ◽  
Vol 90 (1) ◽  
pp. 39-43 ◽  
Author(s):  
X. Xiang ◽  
D. Chang ◽  
Y. Jiang ◽  
C.M. Liu ◽  
X.T. Zu
Keyword(s):  
Thin Films ◽  
Ion Implantation ◽  
Photoelectron Spectroscopy ◽  
Radio Frequency Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Atomic Force ◽  
Light Region ◽  
Uv Visible ◽  
Substrate Temperatures

Anatase TiO2 thin films are deposited on K9 glass samples at different substrate temperatures by radio frequency magnetron sputtering. N ion implantation is performed in the as-deposited TiO2 thin films at ion fluences of 5 × 1016, 1 × 1017, and 5 × 1017 ions/cm2. X-ray diffraction, atomic force microscope, X-ray photoelectron spectroscopy (XPS), and UV–visible spectrophotometer are used to characterize the films. With increasing N ion fluences, the absorption edges of anatase TiO2 films shift to longer wavelengths and the absorbance increases in the visible light region. XPS results show that the red shift of TiO2 films is due to the formation of N–Ti–O compounds. As a result, photoactivity is enhanced with increasing N ion fluence.

scholarly journals Bioinspired Synthesis of Acacia senegal Leaf Extract Functionalized Silver Nanoparticles and Its Antimicrobial Evaluation

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Edwina Olohirere Uzunuigbe ◽  
Abidemi Paul Kappo ◽  
Sixberth Mlowe ◽  
Neerish Revaprasadu
Keyword(s):  
Silver Nanoparticles ◽  
Colour Change ◽  
Silver Ions ◽  
Antibacterial Activities ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Leaf Extracts ◽  
Acacia Senegal ◽  
Transmission Electron ◽  
Antimicrobial Evaluation

Synthesizing nanoparticles with the less environmentally malignant approach using plant extract is of great interest; this is because most of the chemical approaches can be very costly, toxic, and time-consuming. Herein, we report the use of Acacia senegal leaf extracts to synthesize silver nanoparticles (AgNPs) using an environmentally greener approach. Silver ions were reduced using the bioactive components of the plant extracts with observable colour change from faint colourless to a brownish solution as indication of AgNP formation. The structural properties of the as-synthesized AgNPs were characterized using powder X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), and UV-Vis absorption spectrum. Antimicrobial assessment of the as-synthesized AgNPs was explored on some strains of gram-positive and gram-negative bacteria. The obtained results indicate that the as-synthesized AgNPs are pure crystallite of cubic phase of AgNPs, fairly dispersed with a size range of 10–19 nm. The AgNPs were found to be small in size and exhibit significant antibacterial activities, suggesting that the as-synthesized AgNPs could be used in the pharmaceutical and food industries as bactericidal agents.

Thermal Stability and Failure Mechanisms of Au/Tiw(N)/Si and Au/TiW(N)/Si02/Si Systems

1996 ◽  
Vol 427 ◽  
Author(s):  
C. R. Chen ◽  
L. J. Chen
Keyword(s):  
Thermal Stability ◽  
Failure Mechanisms ◽  
Cubic Phase ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Single Face ◽  
Face Centered ◽  
The Stability ◽  
Ar Gas

AbstractThermal stability and failure mechanisms of Au/TiW(N)/Si and Au/TiW(N)/SiO2/Si systems have been studied by both conventional and high-resolution transmission electron microscopy, X- ray diffraction and Auger electron spectroscopy. For films deposited in Ar gas containing 20% N2, a single face-centered-cubic phase was the only crystalline phase detected to form. The samples were found to remain stable after annealing at 700 °C for 30 min. The stability temperature for Au/TiW(N)(Ar:N2=80:20)/SiO2/Si samples was found to be higher than those of Au/TiW(N) (Ar:N2=90:10)/SiO2/Si and Au/TiW/SiO2/Si samples.

scholarly journals Mechanism of improvement of TiN-coated tool life by nitrogen implantation

2001 ◽  
Vol 16 (11) ◽  
pp. 3293-3303 ◽  
Author(s):  
S. J. Bull ◽  
Yu. P. Sharkeev ◽  
S. V. Fortuna ◽  
I. A. Shulepov ◽  
A. J. Perry
Keyword(s):  
Ion Implantation ◽  
Surface Composition ◽  
Slight Reduction ◽  
Nitrogen Implantation ◽  
Force Microscopy ◽  
Tin Coatings ◽  
Coated Tools ◽  
Atomic Force ◽  
Transmission Electron ◽  
Coated Tool

The life of TiN-coated tools can be improved by a post-coating ion implantation treatment, but the mechanism by which this occurs is still not clear. Nitrogen implantation of both physical-vapor-deposited TiN and CVD TiN leads to surface softening as the dose increases, which has been attributed to amorphization. In this study a combination of transmission electron microscopy and atomic force microscopy was used to characterize the microstructure of implanted TiN coatings on cemented carbide for comparison with mechanical property measurements (nanoindentation, residual stress, etc.), made on the same samples. Ion implantation leads to a slight reduction in the grain size of the TiN in the implanted zone, but there is no evidence for amorphization. Surface softening is observed for physical-vapor-deposited TiN, but this is probably due to a combination of changes in surface composition and the presence of a layer of bubbles generated by the very high implantation doses used.

Crystalline phase transformation of colloidal cadmium sulfide nanocrystals

2017 ◽  
Vol 31 (06) ◽  
pp. 1750037
Author(s):  
M. Ghali ◽  
A. M. Eissa ◽  
M. M. Mosaad
Keyword(s):  
Phase Transformation ◽  
Optical Absorption ◽  
Crystalline Phase ◽  
Growth Conditions ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Ph Values ◽  
Transmission Electron

In this paper, we give a microscopic view concerning influence of the growth conditions on the physical properties of nanocrystals (NCs) thin films made of CdS, prepared using chemical bath deposition CBD technique. We show a crystalline phase transformation of CdS NCs from hexagonal wurtzite (W) structure to cubic zincblende (ZB) when the growth conditions change, particularly the solution pH values. This effect was confirmed using X-ray diffraction (XRD), transmission electron microscopy (TEM), optical absorption and photoluminescence (PL) measurements. The optical absorption spectra allow calculation of the bandgap value, [Formula: see text], where significant increase [Formula: see text]200 meV in the CdS bandgap when transforming from Hexagonal to Cubic phase was found.

The Features of a High-Temperature Synthesis of ZrO2 in a Core-Shell ZrO2@C Structure

2019 ◽  
Vol 950 ◽  
pp. 133-137
Author(s):  
Alexander M. Volodin ◽  
Vladimir O. Stoyanovskii ◽  
Vladimir I. Zaykovskii ◽  
Roman M. Kenzhin ◽  
Aleksey A. Vedyagin
Keyword(s):  
Elevated Temperatures ◽  
Cubic Phase ◽  
Core Shell ◽  
X Ray Diffraction ◽  
High Temperature Synthesis ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Carbon Coated ◽  
Physicochemical Methods ◽  
Argon Adsorption

Zirconium oxide was obtained via traditional precipitation from a ZrOCl2 solution with ammonia followed by drying at 110 °C. The carbon-coated samples were synthesized by calcination of the pristine zirconia mixed with polyvinylalcohol. The obtained ZrO2@C samples of core-shell structure as well as the reference samples of pristine zirconia were calcined at different temperatures from 500 to 1400 °C. All the materials were examined by a set of physicochemical methods (a low-temperature argon adsorption, transmission electron microscopy, X-ray diffraction analysis, photoluminescence spectroscopy). It was found that the carbon coating prevents the sintering of the oxide nanoparticles, which allows one to maintain the specific surface area, the size of the oxide core and, finally, stabilize its phase composition. Transformation of the cubic phase into monoclinic phase becomes significantly complicated. Thus, 40% of the cubic phase was detected even after calcination of the ZrO2@C sample at 1400 °C. Moreover, the carbon-coated samples treated at elevated temperatures with subsequent removal of the carbon shell were found to possess the highest concentration of the defects related to a presence of the anion vacancies in zirconia.

Structrual Characterization and Raman Scattering of Epitaxial Aluminum Nitride Thin Films on Si(111)

1992 ◽  
Vol 242 ◽  
Author(s):  
W. J. Meng ◽  
T. A. Perry ◽  
J. Heremans ◽  
Y. T. Cheng
Keyword(s):  
Thin Films ◽  
Aluminum Nitride ◽  
Raman Scattering ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
X Ray Diffraction ◽  
X Ray ◽  
Reactive Sputter Deposition ◽  
Transmission Electron ◽  
Substrate Temperatures

ABSTRACTThin films of aluminum nitride were grown epitaxially on Si(111) by ultra-high-vacuum dc magnetron reactive sputter deposition. Epitaxy was achieved at substrate temperatures of 600° C or above. We report results of film characterization by x-ray diffraction, transmission electron microscopy, and Raman scattering.

Synthesis and upconversion luminescence properties of CaF2:Yb3+,Er3+ nanoparticles obtained from SBA-15 template

2010 ◽  
Vol 25 (10) ◽  
pp. 2035-2041 ◽  
Author(s):  
Zhiguo Xia ◽  
Peng Du
Keyword(s):  
Electron Microscopy ◽  
Upconversion Luminescence ◽  
Emission Spectra ◽  
Average Diameter ◽  
Cubic Phase ◽  
Pumping Power ◽  
X Ray Diffraction ◽  
Temperature Dependent ◽  
X Ray ◽  
Transmission Electron

CaF2:Yb3+,Er3+ upconversion (UC) luminescence nanoparticles have been synthesized using mesoporous silica (SBA-15) as a hard template. The samples were characterized by x-ray diffraction, Fourier transform infrared spectra, field-emission scanning electron microscopy, transmission electron microscopy, and UC emission spectra, respectively. Highly crystalline cubic phase CaF2:Yb3+,Er3+ nanoparticles are uniformly distributed with an average diameter of about 40–50 nm, and the formation process is also demonstrated. The UC fluorescence has been realized in the as-prepared CaF2:Yb3+,Er3+ nanoparticles on 980-nm excitation. The UC emission transitions for 4F9/2–4I15/2 (red), 2H11/2–4I15/2 (green), 4S3/2–4I15/2 (green), and 2H9/2–4I15/2 (violet) in the Yb3+/Er3+ codoped CaF2 nanoparticles depending on pumping power and temperature have been discussed. The UC mechanism, especially the origin on the temperature-dependent UC emission intensities ratio between 2H11/2 and 4S3/2 levels, have been proposed.

Sign in / Sign up

Export Citation Format

Share Document