Strain-Rate Effects on the Room Temperature Tensile Properties of a TiAl Alloy

1992 ◽  
Vol 288 ◽  
Author(s):  
Y-W. Kim ◽  
D.M. Dimiduk
Keyword(s):  
Strain Rate ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tial Alloy ◽  
Strain Rate Effects ◽  
Rate Effects

scholarly journals Strain Rate Effects on Tensile Properties of HDPE-PP Composite Prepared by Extrusion and Injection Moulding Method

2019 ◽  
Vol 10 (03) ◽  
pp. 205-215
Author(s):  
Harekrushna Sutar ◽  
Himanshu Sekhar Maharana ◽  
Chiranjit Dutta ◽  
Rabiranjan Murmu ◽  
Sangram Patra
Keyword(s):  
Strain Rate ◽  
Tensile Properties ◽  
Injection Moulding ◽  
Strain Rate Effects ◽  
Rate Effects

Strain Rate Effects in SA-106 Carbon Steel Pipe

1982 ◽  
Vol 104 (1) ◽  
pp. 31-35 ◽  
Author(s):  
D. Peterson ◽  
J. E. Schwabe ◽  
D. G. Fertis
Keyword(s):  
Carbon Steel ◽  
Yield Strength ◽  
Strain Rate ◽  
Tensile Properties ◽  
Nuclear Power ◽  
Power Plants ◽  
Experimental Modeling ◽  
Steel Pipe ◽  
Strain Rate Effects ◽  
Rate Effects

Experiments were performed to measure the effect of strain rate on the tensile properties of SA-106 carbon steel pipe, in support of analysis and experimental modeling of postulated pipe whip in nuclear power plants. It was observed that increasing the strain rate from 4 × 10−4 to 4 s−1 raised the yield strength by approximately 30 percent.

Tensile Properties of Ni-Based Superalloy 720Li: Temperature and Strain Rate Effects

2008 ◽  
Vol 39 (10) ◽  
pp. 2340-2350 ◽  
Author(s):  
K. Gopinath ◽  
A.K. Gogia ◽  
S.V. Kamat ◽  
R. Balamuralikrishnan ◽  
U. Ramamurty
Keyword(s):  
Strain Rate ◽  
Tensile Properties ◽  
Strain Rate Effects ◽  
Rate Effects

Strain rate effects on dynamic tensile properties of open-hole composite laminates

2020 ◽  
Vol 19 ◽  
pp. 226-232 ◽  
Author(s):  
Jin Sun ◽  
Zhen Jing ◽  
Jian Wu ◽  
Weibo Wang ◽  
Diantang Zhang ◽  
...  
Keyword(s):  
Strain Rate ◽  
Tensile Properties ◽  
Composite Laminates ◽  
Strain Rate Effects ◽  
Rate Effects ◽  
Open Hole ◽  
Dynamic Tensile Properties

scholarly journals Temperature and Strain-Rate Effects on Deformation Mechanisms in Irradiated Stainless Steel

1994 ◽  
Vol 373 ◽  
Author(s):  
J. L. Brimhall ◽  
J. I. Cole ◽  
J. S. Vetrano ◽  
S. M. Bruemmer
Keyword(s):  
Stainless Steel ◽  
Strain Rate ◽  
Room Temperature ◽  
Deformation Mode ◽  
Radiation Hardening ◽  
Strain Rates ◽  
Lower Yield ◽  
Strain Rate Effects ◽  
Rate Effects ◽  
Higher Temperature

AbstractAnalysis of the deformation microstructures in ion-irradiated stainless steel shows twinning to be the predominant deformation mode at room temperature. Dislocation channelling also occurs under slow strain rate conditions. Stresses required for twinning were calculated by the model of Venables and are compatible with observed yield stresses in neutron-irradiated material if loops are the principal twin source. Computation of the expected radiation hardening from the defect structure, based on a simple model, is consistent with yield strengths measured on neutron-irradiated steels. Lower yield stresses and greater thermal energy at 288°C lessen the probability of twinning and dislocation channeling becomes the primary deformation mode at the higher temperature. However, preliminary results show that some twinning does occur in the irradiated stainless steel even at the higher temperature when higher strain rates are used.

Sign in / Sign up

Export Citation Format

Share Document