A Particular Structure of B-doped μc-Si/a-Si:H Layers on Insulator

1992 ◽  
Vol 283 ◽  
Author(s):  
M. Le Berre ◽  
M. Lemiti ◽  
P. Pinard ◽  
E. Bustarret ◽  
W. Grieshaber ◽  
...  
Keyword(s):  
Cross Section ◽  
Microcrystalline Structure ◽  
X Ray Diffraction ◽  
Relative Thickness ◽  
X Ray ◽  
Preparation Conditions ◽  
Wide Range ◽  
Local Measurements ◽  
Crystalline Nature ◽  
Optimized Conditions

ABSTRACTMicrocrystalline films of thicknesses ranging from 0.3 to 1.1 μm have been deposited on oxidized silicon wafers by PECVD in a 50KHz capacitive discharge reactor at 450°C. Two series of films have been elaborated over a wide range of boron concentrations at the same H2:SiH4 ratio of 9:1. Cross section TEM micrographs showed the films to consist of two sublayers of distinct crystalline nature, whose relative thickness depends on the preparation conditions. With a strongly <220> textured microcrystalline structure, the overlayer snowed a columnar morphology, while the amorphous underlayer reached thicknesses of 350nm. Two additional striking features were observed by TEM: - The grains took two symmetrical orientations relative to the preferential [220] growth axis;- The interface between the amorphous and crystalline regions had a sawtooth pattern with a period around 300nm. In contrast to these microstructural results, the B-profile as measured by SIMS was found to be fiat accross the whole thickness. These local measurements are compared to the results of grazing X ray diffraction and Raman measurements. We observe and discuss a discrepancy between the X ray coherence length and the dimensions of the columns as observed by TEM. While optimized conditions lead to a vanishing amorphous sublayer, the more original features described above are tentatively interpreted taking into account the high compressive strains in the layers deposited at low plasma frequencies.

Freeze-Fracture Replication of Frozen Outer Segments of Rat Retinal Rods

1969 ◽  
Vol 27 ◽  
pp. 392-393
Author(s):  
Thomas S. Leeson ◽  
C. Roland Leeson
Keyword(s):  
Electron Microscopy ◽  
Cross Section ◽  
Outer Segment ◽  
Freeze Fracture ◽  
X Ray Diffraction ◽  
X Ray ◽  
Outer Segments ◽  
Retinal Rods ◽  
Temperature Electron ◽  
Freeze Etching

Numerous previous studies of outer segments of retinal receptors have demonstrated a complex internal structure of a series of transversely orientated membranous lamellae, discs, or saccules. In cones, these lamellae probably are invaginations of the covering plasma membrane. In rods, however, they appear to be isolated and separate discs although some authors report interconnections and some continuities with the surface near the base of the outer segment, i.e. toward the inner segment. In some species, variations have been reported, such as longitudinally orientated lamellae and lamellar whorls. In cross section, the discs or saccules show one or more incisures. The saccules probably contain photolabile pigment, with resulting potentials after dipole formation during bleaching of pigment. Continuity between the lamina of rod saccules and extracellular space may be necessary for the detection of dipoles, although such continuity usually is not found by electron microscopy. Particles on the membranes have been found by low angle X-ray diffraction, by low temperature electron microscopy and by freeze-etching techniques.

The 3-Dimensional Molecular Structure of the Actin Filament Revisited

1985 ◽  
Vol 43 ◽  
pp. 480-481
Author(s):  
U. Aebi ◽  
R. Millonig ◽  
H. Salvo
Keyword(s):  
Actin Filament ◽  
Supramolecular Assembly ◽  
Specimen Preparation ◽  
X Ray Diffraction ◽  
Single Filament ◽  
X Ray ◽  
3 Dimensional ◽  
Filament Diameter ◽  
Preparation Conditions ◽  
Apparent Diameter

To date, most 3-D reconstructions of undecorated actin filaments have been obtained from actin filament paracrystal data (for refs, see 1,2). However, due to the fact that (a) the paracrystals may be several filament layers thick, and (b) adjacent filaments may sustantially interdigitate, these reconstructions may be subject to significant artifacts. None of these reconstructions has permitted unambiguous tracing or orientation of the actin subunits within the filament. Furthermore, measured values for the maximal filament diameter both determined by EM and by X-ray diffraction analysis, vary between 6 and 10 nm. Obviously, the apparent diameter of the actin filament revealed in the EM will critically depend on specimen preparation, since it is a rather flexible supramolecular assembly which can easily be bent or distorted. To resolve some of these ambiguities, we have explored specimen preparation conditions which may preserve single filaments sufficiently straight and helically ordered to be suitable for single filament 3-D reconstructions, possibly revealing molecular detail.

Fractionation of polymethylene chains: An electron crystallographic investigation

1986 ◽  
Vol 44 ◽  
pp. 794-795
Author(s):  
Douglas L. Dorset
Keyword(s):  
Cross Section ◽  
Binary Systems ◽  
Linear Chain ◽  
Pure Component ◽  
Organic Substrates ◽  
Crystallographic Investigation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molecular Sizes ◽  
The Stability

A variety of linear chain materials exist as polydisperse systems which are difficultly purified. The stability of continuous binary solid solutions assume that the Gibbs free energy of the solution is lower than that of either crystal component, a condition which includes such factors as relative molecular sizes and shapes and perhaps the symmetry of the pure component crystal structures.Although extensive studies of n-alkane miscibility have been carried out via powder X-ray diffraction of bulk samples we have begun to examine binary systems as single crystals, taking advantage of the well-known enhanced scattering cross section of matter for electrons and also the favorable projection of a paraffin crystal structure posited by epitaxial crystallization of such samples on organic substrates such as benzoic acid.

scholarly journals Multidimensional Ln-Aminophthalate Photoluminescent Coordination Polymers

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1786
Author(s):  
Carla Queirós ◽  
Chen Sun ◽  
Ana M. G. Silva ◽  
Baltazar de Castro ◽  
Juan Cabanillas-Gonzalez ◽  
...  
Keyword(s):  
Water Content ◽  
Coordination Polymers ◽  
Metal Ion ◽  
Low Cost ◽  
Microwave Assisted Synthesis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wide Range ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

The development of straightforward reproducible methods for the preparation of new photoluminescent coordination polymers (CPs) is an important goal in luminescence and chemical sensing fields. Isophthalic acid derivatives have been reported for a wide range of applications, and in addition to their relatively low cost, have encouraged its use in the preparation of novel lanthanide-based coordination polymers (LnCPs). Considering that the photoluminescent properties of these CPs are highly dependent on the existence of water molecules in the crystal structure, our research efforts are now focused on the preparation of CP with the lowest water content possible, while considering a green chemistry approach. One- and two-dimensional (1D and 2D) LnCPs were prepared from 5-aminoisophthalic acid and Sm3+/Tb3+ using hydrothermal and/or microwave-assisted synthesis. The unprecedented LnCPs were characterized by single-crystal X-ray diffraction (SCRXD), powder X-ray diffraction (PXRD), Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM), and their photoluminescence (PL) properties were studied in the solid state, at room temperature, using the CPs as powders and encapsulated in poly(methyl methacrylate (PMMA) films, envisaging the potential preparation of devices for sensing. The materials revealed interesting PL properties that depend on the dimensionality, metal ion, co-ligand used and water content.

Silicate-germanate K2Y[(Si3Ge)O10(OH)] with unusual complex corrugated layer and its correlation to ring silicate gerenite and chain silicate chkalovite

2020 ◽  
Vol 235 (4-5) ◽  
pp. 167-172
Author(s):  
Anastasiia P. Topnikova ◽  
Elena L. Belokoneva ◽  
Olga V. Dimitrova ◽  
Anatoly S. Volkov ◽  
Leokadiya V. Zorina
Keyword(s):  
Low Temperature ◽  
Cross Section ◽  
Complex Anion ◽  
Diffraction Experiment ◽  
X Ray Diffraction ◽  
Unit Cell Parameters ◽  
X Ray ◽  
Cell Parameters ◽  
Chain Silicate ◽  
Novel Complex

AbstractA new silicate-germanate K2Y[(Si3Ge)O10(OH)] was synthesized hydrothermally in a system Y2O3:GeO2:SiO2 = 1:1:2 (T = 280 °C; P = 90–100 atm.); K2CO3 was added to the solution as a mineralizer. Single-crystal X-ray diffraction experiment was carried out at low temperature (150 K). The unit cell parameters are a = 10.4975(4), b = 6.9567(2), c = 15.4001(6) Å, β = 104.894(4)°; V = 1086.86(7) Å3; space group is P 21/c. A novel complex anion is presented by corrugated (Si,Ge) tetrahedral layers connected by couples of YO6 octahedra into the mixed microporous framework with the channels along b and a axes, the maximal size of cross-section is ~5.6 Å. This structure has similarity with the two minerals: ring silicate gerenite (Ca,Na)2(Y,REE)3Si6O18 · 2H2O and chain silicate chkalovite Na2BeSi2O6. Six-member rings with 1̅ symmetry as in gerenite are distinguished in the new layer. They are mutually perpendicular to each other and connected by additional tetrahedra. Straight crossing chains in chkalovite change to zigzag four-link chains in the new silicate-germanate layer.

2D X-ray diffraction and molecular modelling of the crystalline structure of polyesters under uniaxial stress

2021 ◽  
pp. 096739112199822
Author(s):  
Ahmed I Abou-Kandil ◽  
Gerhard Goldbeck
Keyword(s):  
Crystalline Structure ◽  
Molecular Modelling ◽  
Three Dimensional ◽  
Uniaxial Stress ◽  
X Ray Diffraction ◽  
X Ray ◽  
Wide Range ◽  
Modelling Techniques ◽  
Diffraction Patterns

Studying the crystalline structure of uniaxially and biaxially drawn polyesters is of great importance due to their wide range of applications. In this study, we shed some light on the behaviour of PET and PEN under uniaxial stress using experimental and molecular modelling techniques. Comparing experiment with modelling provides insights into polymer crystallisation with extended chains. Experimental x-ray diffraction patterns are reproduced by means of models of chains sliding along the c-axis leading to some loss of three-dimensional order, i.e. moving away from the condition of perfect register of the fully extended chains in triclinic crystals of both PET and PEN. This will help us understand the mechanism of polymer crystallisation under uniaxial stress and the appearance of mesophases in some cases as discussed herein.

scholarly journals UV-Accelerated Photocatalytic Degradation of Pesticide over Magnetite and Cobalt Ferrite Decorated Graphene Oxide Composite

Plants ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 6
Author(s):  
Asma Tabasum ◽  
Mousa Alghuthaymi ◽  
Umair Yaqub Qazi ◽  
Imran Shahid ◽  
Qamar Abbas ◽  
...  
Keyword(s):  
Spectroscopic Techniques ◽  
Combined Effects ◽  
X Ray Diffraction ◽  
Contributing Factors ◽  
Reaction Conditions ◽  
X Ray ◽  
Oxidant Concentration ◽  
Optimized Conditions ◽  
High Degradation Rate ◽  
Considerable Loss

Pesticides are one of the main organic pollutants as they are highly toxic and extensively used worldwide. The reclamation of wastewater containing pesticides is of utmost importance. For this purpose, GO-doped metal ferrites (GO-Fe3O4 and GO-CoFe2O4) were prepared and characterized using scanning electron microscopy, X-ray diffraction and Fourier transform infrared spectroscopic techniques. Photocatalytic potentials of catalysts were investigated against acetamiprid’s degradation. A detailed review of the parametric study revealed that efficiency of overall Fenton’s process relies on the combined effects of contributing factors, i.e., pH, initial oxidant concentration, catalyst dose, contact time, and acetamiprid load. ~97 and ~90% degradation of the acetamiprid was achieved by GO-CoFe2O4 and GO-Fe3O4, respectively during the first hour under UV radiations at optimized reaction conditions. At optimized conditions (i.e., pH:3, [H2O2]: 14.5 mM (for Fe3O4, GO-Fe3O4, and GO-CoFe2O4) and 21.75 mM (for CoFe2O4), catalysts: 100 mgL−1, time: 60min) the catalysts exhibited excellent performance, with high degradation rate, magnetic power, easy recovery at the end, and efficient reusability (up to 5 cycles without any considerable loss in catalytic activity). A high magnetic character offers its easy separation from aqueous systems using an external magnet. Moreover, the combined effects of experimental variables were assessed simultaneously and justified using response surface methodology (RSM).

INFLUENCE OF INTERFACE AND POLARIZATION ON MAGNETOELECTRIC COUPLING IN Ni-LEAD ZIRCONIUM TITANATE-Ni TRILAYERS DERIVED BY ELECTROLESS DEPOSITION

2012 ◽  
Vol 19 (03) ◽  
pp. 1250030
Author(s):  
K. BI ◽  
Y. G. WANG
Keyword(s):  
Cross Section ◽  
Electroless Deposition ◽  
Mechanical Deformation ◽  
Interface Roughness ◽  
Zirconium Titanate ◽  
Interface Conditions ◽  
Lead Zirconium Titanate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Voltage Coefficient

Magnetoelectric (ME) coupling in layered structures of magnetostrictive and piezoelectric phases are mediated by mechanical deformation and depends strongly on the interface conditions. Ni -lead zirconium titanate- Ni trilayers with neither electrodes nor bonding layers have been derived by electroless deposition. The structure of the electroless deposited Ni layer was characterized by X-ray diffraction. The cross-section of the Ni/PZT layers was investigated using scanning electron microscopy. The value of ME voltage coefficient (αE,31) increases as the interface roughness increases. The maximum of αE,31 for the Ni/PZT/Ni trilayers polarized after electroless deposition is higher than that for the Ni/PZT/Ni trilayers polarized before electroless deposition. It is essential to optimize the interface and the polarization to obtain higher ME voltage coefficient.

scholarly journals Development of an Oxcarbazepine Solid Dispersion Using Skimmed Milk to Improve the Solubility and Dissolution Profile

2019 ◽  
Vol 11 (05) ◽  
Author(s):  
M. Shah ◽  
D. Patel
Keyword(s):  
Electron Microscopy ◽  
Solid Dispersion ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Infra Red ◽  
Crystalline Nature ◽  
Skimmed Milk ◽  
Scanning Electron

Oxcarbazepine has low solubility and low oral bioavailability, so it’s a challenge to formulate suitable dosage form. In this present investigation, to improve the dissolution rate and solubility, skimmed milk is used as a carrier. Physical mixers were prepared using various drugs to carrier ratio and spray drying technology was used to develop solid dispersion with the carrier. Various techniques were used to characterize the solid dispersion immediately after they were made which includes differential scanning calorimetry, scanning electron microscopy, fourier transform infra- red spectroscopy, X-ray diffraction and in-vitro dissolution profiles. The differential scanning calorimetry thermograms of raw drug indicated of its anhydrous crystalline nature. In thermograms of solid dispersion, the characteristic peak was absent suggesting the change from crystalline nature to amorphous form. X-ray diffraction confirmed those results. X-ray diffraction results of raw drug showed highly intense peak characteristic of its crystalline nature where solid dispersion showed less intense, more diffused peak indicating the change in crystalline form. Fourier transforms infra-red spectroscopy studies showed there was no interaction between drug and carrier. Scanning electron microscopy support the amorphous nature of mixer. The whole formulation showed distinct enhancement in the drug release behavior and solubility. The optimum oxcarbazepine to skimmed milk ratio 1:3 enhances the in-vitro drug release by 3.5 fold and also show distinct increase in solubility. It was concluded that for improvement of solubility of poorly water soluble oxcarbazepine, skimmed milk powder as a carrier can be utilize very well.

scholarly journals Theoretical study of the properties of X-ray diffraction moiré fringes. II. Illustration of angularly integrated moiré images

2019 ◽  
Vol 75 (4) ◽  
pp. 610-623
Author(s):  
Jun-ichi Yoshimura
Keyword(s):  
Incident Wave ◽  
Angular Width ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Acta Cryst ◽  
Low Contrast ◽  
X Ray ◽  
Moiré Fringes ◽  
Wide Range ◽  
Fringe Patterns

Using a theory of X-ray diffraction moiré fringes developed in a previous paper, labelled Part I [Yoshimura (2015). Acta Cryst. A71, 368–381], the X-ray moiré images of a silicon bicrystal having a weak curvature strain and an interspacing gap, assumed to be integrated for an incident-wave angular width, are simulation-computed over a wide range of crystal thicknesses and incident-wave angular width, likely under practical experimental conditions. Along with the simulated moiré images, the graphs of characteristic quantities on the moiré images are presented for a full understanding of them. The treated moiré images are all of rotation moiré. Mo Kα1 radiation and the 220 reflection were assumed in the simulation. The results of this simulation show that fringe patterns, which are significantly modified from simple straight fringes of rotation moiré, appear in some ranges of crystal thicknesses and incident-wave angular width, due to a combined effect of Pendellösung oscillation and an added phase difference from the interspacing gap, under the presence of a curvature strain. The moiré fringes which slope to the perpendicular direction to the diffraction vector in spite of the assumed condition of rotation moiré, and fringe patterns where low-contrast bands are produced with a sharp bend of fringes arising along the bands are examples of the modified fringe pattern. This simulation study provides a wide theoretical survey of the type of bicrystal moiré image produced under a particular condition.

Sign in / Sign up

Export Citation Format

Share Document