Corrosion Behavior of Rapidly Solidified Fe-Ti-P Alloys With Cu, Cr, and B Additions

1983 ◽  
Vol 28 ◽  
Author(s):  
C. R. Shastry ◽  
R. M. Latanision ◽  
H. E. Townsend
Keyword(s):  
Corrosion Resistance ◽  
Melt Spinning ◽  
Anodic Polarization ◽  
Alloy Composition ◽  
Amorphous Structure ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
X Ray ◽  
B Additions ◽  
Rapidly Solidified

ABSTRACTRapidly solidified ribbons of Fe67Ti13P(20-x)Bx (x= 0, 7, 20 a/o) and Fe(85-y)Ti l5Py (y=5, 10 a/o) alloys were produced by melt spinning, and their structure and anodic polarization behavior were examined by x-ray diffraction and potentio-dynamic polarization measurements in deaerated 1 N H2SO4, respectively. The only alloy that developed an amorphous structure on rapid solidification, Fe67Ti13B20, exhibited poor corrosion resistance, whereas crystalline alloys with 10 a/o or more P exhibited a tendency to passivate during anodic polarization. Substituting Cr for Ti led to significant improvement in corrosion resistance and promoted development of glassy structures in Fe67(TiCr)13P13B7 compositions. No such improvements were observed when Cu was substituted for Ti. It is concluded that alloy composition is more important than degree of crystallinity in determining corrosion resistance.

scholarly journals The Development of Rapidly Solidified Magnesium – Copper Ribbons

2016 ◽  
Vol 61 (2) ◽  
pp. 1083-1088
Author(s):  
M. Pastuszak ◽  
G. Cieślak ◽  
A. Dobkowska ◽  
J. Mizera ◽  
K.J. Kurzydłowski
Keyword(s):  
Corrosion Resistance ◽  
Cooling Rate ◽  
Melt Spinning ◽  
Diffraction Method ◽  
Electrode System ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Copper Addition ◽  
Rapidly Solidified ◽  
Thermal Stability Of

Abstract The aim of the present work was to plan and carry out an experiment consisting of amorphization of industrial magnesium alloy WE 43 (Mg - 4 Y - 3 RE - 0.5 Zr) modified by the copper addition. Investigated alloy modified with 20% of copper was rapidly quenched with the use of melt spinning technique. The effects of cooling rate on the structure and properties of the obtained material were extensively analyzed. The structure and phase analysis of samples were examined using X-ray diffraction method (XRD) while the thermal stability of the samples was determined by differential scanning calorimetry (DSC). Microstructure observations were also conducted. The microhardness tests (HV0.02) and corrosion resistance tests were carried out to investigate the properties of the material. Corrosion resistance measurements were held using a typical three-electrode system. As the result of the research, the effect of cooling rate on microstructure and properties of investigated alloy was determined.

scholarly journals Effect of Fe-Ni Substitution in FeNiSiB Soft Magnetic Alloys Produced by Melt Spinning

2021 ◽  
Vol 21 (4) ◽  
pp. 79-89
Author(s):  
Muhammed Fatih Kılıçaslan ◽  
Yasin Yılmaz ◽  
Bekir Akgül ◽  
Hakan Karataş ◽  
Can Doğan Vurdu
Keyword(s):  
Melt Spinning ◽  
Amorphous Structure ◽  
Soft Magnetic Materials ◽  
X Ray Diffraction ◽  
Soft Magnetic ◽  
Sem Images ◽  
X Ray ◽  
Soft Magnetic Alloys ◽  
Fe Content ◽  
Rapid Solidification Technique

Abstract Alloys of FeNiSiB soft magnetic materials containing variable Fe and Ni contents (wt.%) have been produced by melt spinning method, a kind of rapid solidification technique. The magnetic and structural properties of FeNiSiB alloys with soft magnetic properties were investigated by increasing the Fe ratio. X-ray diffraction analysis and SEM images shows that the produced alloy ribbons generally have an amorphous structure, together with also partially nanocrystalline regions. It was observed that the structure became much more amorphous together with increasing Fe content in the composition. Among the alloy ribbons, the highest saturation magnetization was obtained as 0.6 emu/g in the specimen with 50 wt.% Fe. In addition, the highest Curie temperature was observed in the sample containing 46 wt.% Fe.

Hrem Studies of Rapidly Solidified Ni-Fe-Al-B Shape Memory Alloys.

1991 ◽  
Vol 246 ◽  
Author(s):  
R. Pērez ◽  
J. A. Juārez-Islas ◽  
P. Johansson ◽  
M. Wallin ◽  
S. J. Savage
Keyword(s):  
Shape Memory ◽  
Martensite Transformation ◽  
Melt Spinning ◽  
Image Contrast ◽  
X Ray Diffraction ◽  
Recoverable Strain ◽  
X Ray ◽  
Atomic Structures ◽  
Wide Range ◽  
Rapidly Solidified

AbstractA series of (NixFeyAlz)0.9983B0.0017 (where x=58-60, y=13-15 and z=26-28, in at%) alloys have been rapidly solidified by - melt spinning. The ribbons have been characterized by HREM, DSC, X-ray diffraction and recoverable strain measurements. The as-cast alloys exhibit excellent bend ductility (in contrast to B2 type alloys conventionally cast) and a wide range of transformation temperatures: Ms=244-466 K, Mf=200-395K, As=236-427K and Af=262-526K. X-ray diffraction shows the presence of β (NiAl), β′ (NiAl), γ (Ni3Al), γ′ (Ni3A1), Ni and other phases such as Fe3Al, FeAl, FeNi and Al5Fe2. It is the β- β′ diffusionless transformation which is responsible for the shape memory effect. The results obtained by transmission electron microscopy (TEM) show two different types of crystalline grains. In one case, the grains have a high density of twins which are the fingerprints of the martensite transformation. However, other areas in the specimen show crystalline grains with very poor image contrast due to the transformation from β′ -β. There are also sections in the specimens with domains of both crystalline sgrains in coexistance. Both crystalline grains have large amounts of precipitates. In the β′ (NiAl) phase the size of the precipitates range fron lnm to lOnm. In the γ (Ni3Al) phase large precipitates (20nm) can be found. Some of them display pentagonal shapes which resemble the image contrast obtained in the TEM for small icosahedral metallic particles. Experimental evidence is also obtained on different habit or twin planes. HREM images from the twinned areas suggest diferent kinds of atomic structures for the parent and martensite crystalline sections. These results give some insights into the nature of the martensite transformation.

Rapid Solidification Microstructures and Precipitation in AL-Mn Alloys

1983 ◽  
Vol 28 ◽  
Author(s):  
R. J. Schaefer ◽  
D. Shechtman ◽  
F. S. Biancaniello
Keyword(s):  
Rapid Solidification ◽  
Growth Kinetics ◽  
Melt Spinning ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rapidly Solidified ◽  
Solidification Microstructures ◽  
Al Matrix

ABSTRACTRapidly solidified Al containing up to to 15 wt.% Mn was prepared by melt spinning. The alloys were examined by TEM and X-ray diffraction in the as-spun condition and after annealing at 450°C. Four precipitate phases were detected, and their growth kinetics were correlated to subgrain structures in the Al matrix.

A microstructural characterization of Co-Zr type permanent-magnet materials

1991 ◽  
Vol 49 ◽  
pp. 782-783
Author(s):  
K. R. Lawless ◽  
G. C. Hadjipanayis
Keyword(s):  
Melt Spinning ◽  
Microstructural Characterization ◽  
X Ray Diffraction ◽  
Ion Milling ◽  
X Ray ◽  
Heat Treated ◽  
Diffraction Patterns ◽  
Rapidly Solidified ◽  
Hard Magnetic Properties

Considerable interest has been shown recently in the hard magnetic properties of Co-Zr, Co-Zr-B, and Co-Hf-B alloys, but as yet no detailed microstructural studies have been published. The Co-Zr phase diagram seems to be reasonably well known, although the crystal structure of the Co11Zr2 phase is only partially determined. This paper will report on some preliminary studies of rapidly solidified Co-Zr-B-Si and Co-Hf-B-Si alloys and binary Co-Zr alloys.All specimens used in this study were prepared by melt spinning. Specific alloys were heat treated at temperatures from 650 to 900°C. TEM specimens were prepared from ribbon material by ion milling.X-ray diffraction studies of these alloys all showed a characteristic broad peak centered around d = 0.205nm. Although it was obvious that this was a complex peak, attempts to deconvolute it were unsuccessful. SAD patterns revealed that major phases in the alloys were very heavily faulted, thus giving rise to the very confusing X-ray diffraction patterns.

Microstructural analysis for Sn-Bi-Sb-In alloy prepared by rapid solidification

2016 ◽  
Vol 12 (2) ◽  
pp. 4244-4254
Author(s):  
Sara Mosaad Mahlab ◽  
Mustafa Kamal ◽  
Abd El-Raouf Mansour
Keyword(s):  
Electron Microscopy ◽  
Microstructure Evolution ◽  
Melt Spinning ◽  
Vickers Microhardness ◽  
Microstructural Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Rapidly Solidified ◽  
Melt Spinning Technique ◽  
Scanning Electron

In the present study, Sn70-X at.% -Bi15 at.% -Sb15 at.%- Inx at.%  alloy ( x= 0, 2, 4, 6),  were prepared by melt spinning technique. Optical microscopy, scanning electron microscopy combined with energy dispersive X-ray analysis (SEM-EDX), X-ray diffraction analysis (XRD), and Vickers microhardness (Hv); were used to characterize the phase transformation and the microstructure evolution. The results contribute to the understanding of the microstructure evolution in alloys of the type prepared by melt spinning technique. This work reports on a comparative study of the rapidly solidified, in order to compare the microhardness and microstructural analysis. 

scholarly journals Microstructural Investigations of Rapidly Solidified Al-Co-Y Alloys

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
B. Avar ◽  
M. Gogebakan ◽  
M. Tarakci ◽  
Y. Gencer ◽  
S. Kerli
Keyword(s):  
Melt Spinning ◽  
Alloy System ◽  
Supercooled Liquid ◽  
Amorphous Structure ◽  
Supercooled Liquid Region ◽  
Liquid Region ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Glass Forming ◽  
Rapidly Solidified

The alloys with different compositions in the Al-rich corner of the Al-Co-Y ternary system were prepared by conventional casting and further processed by melt-spinning technique. The microstructure and the thermal behavior of the alloys were analyzed by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and differential thermal analysis (DTA). It was found that only rapidly solidified Al85Co7Y8alloy exhibited the best glass forming ability (GFA) and a fully amorphous structure. Besides, Al85Co13Y2and Al85Co2Y13alloy ribbons were fully crystalline, whereas Al85Co10Y5and Al85Co5Y10alloy ribbons consisted of some crystalline phases within an amorphous matrix. The SEM results showed the same trend that the crystalline phase fraction decreases with the approaching into best glass former. From DSC results, only Al85Co7Y8amorphous alloy exhibited a glass transition temperature (Tg) at 569 K, and its supercooled liquid region (ΔTx=Tx−Tg) was found to be 17 K. Moreover, other calculated GFA parameters for this alloy system were also discussed.

The Effect of Hydrogen on an Iron Based Amorphous Alloy

1981 ◽  
Vol 8 ◽  
Author(s):  
H. Shahani ◽  
H. Soderhjelm ◽  
Mats Nygren
Keyword(s):  
Hydrogen Content ◽  
Atomic Structure ◽  
Melt Spinning ◽  
Amorphous Structure ◽  
Hydrogen Gas ◽  
X Ray Diffraction ◽  
Cooling Rates ◽  
X Ray ◽  
Amorphous Ribbons ◽  
Partial Pressures

ABSTRACTIn this· investigation we have systematically studied the brittleness and the atomic structure in an Fe(SiBC) alloy. Different amounts of hydrogen have been dissolved in the alloy. It has then been studied at different cooling rates.Hydrogen gas of different partial pressures was dissolved into the melt. The alloy was then rapidly quenched by a chill block melt spinning method. The cooling rates were changed by changing the velocity on the chilling roll. The brittleness and the atomic structure were examined by bending tests and x-ray diffraction.X-ray diffractions showed that the ribbons were amorphous when the cooling rate was sufficient. Amorphous ribbons without any hydrogen were ductile, crystalline ribbons of this alloy were brittle. The ribbons with dissolved hydrogen and amorphous structure were brittle even at small amounts of hydrogen. At the highest cooling rates the ribbons with low hydrogen content were ductile. There seems to be a connection between the hydrogen content and the amorphous ribbons ductility. The hydrogen content only has a slight influence to amorphous structure.

Mechanical Properties of Ordered Fe-Al-X Alloys

1990 ◽  
Vol 213 ◽  
Author(s):  
Ujjwal Prakash ◽  
Robert A. Buckley ◽  
Howard Jones
Keyword(s):  
Electron Microscopy ◽  
Melt Spinning ◽  
Composition Range ◽  
Tensile Fracture ◽  
Strengthening Mechanisms ◽  
X Ray Diffraction ◽  
X Ray ◽  
Al Content ◽  
Heat Treated ◽  
Rapidly Solidified

ABSTRACTFe-Al-X alloys (X = Cr, Mo) in the composition range 50 to 80 at. % Fe, 0 to 20 at. % X were rapidly solidified by chill-block melt-spinning. As-spun and heat treated ribbons were characterised by optical and electron microscopy and X-ray diffraction. Strengthening mechanisms were identified using microhardness measurements. Tensile fracture surfaces of ribbons reveal ductile to cleavage to intergranular fracture transitions with increasing Al-content. An increasing preponderance of cleavage fracture with increasing ternary substitution for Fe was observed.

Effect of Crystallization on the Electrical Resistance and Structure of Amorphous Fe-Co-Cr-B-Si Alloys / Wpływ Krystalizacji Na Oporność Elektryczną I Strukturę Amorficznych Stopów Fe-Co-Cr-B-Si

2012 ◽  
Vol 57 (4) ◽  
pp. 1031-1039
Author(s):  
H. Solomon ◽  
N. Solomon
Keyword(s):  
Electrical Resistivity ◽  
Electrical Properties ◽  
Amorphous Alloys ◽  
Melt Spinning ◽  
Amorphous Structure ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Investigation Methods ◽  
Melt Spinning Technique

The goal of this paper is to present the influence of temperature variation and iron substitution with Co on the structure and electrical properties of amorphous Fe75-xCoxCr1B7Si17 alloys (where x=1, 4, 7, and 10 at.%), obtained by melt-spinning technique. The electrical resistivity of the samples was measured by using a usual four-probe method from -160°C to 750°C. The electrical resistivity was also measured at room temperature for the amorphous Fe75-xCoxCr1B7Si17 ribbons annealed at various temperatures for different holding time. The annealed samples were also investigated by Vickers microhardness test. The amorphous structure of tested materials was examined by X-ray diffraction (XRD), Mossbauer spectroscopy, differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) methods. Experimental results confirmed the utility of applied investigation methods and the influence of the Co content and annealing process on the crystallization, structure and electrical properties of examined amorphous alloys.

Sign in / Sign up

Export Citation Format

Share Document