Thermal Stability of Supported Titania Membranes

1992 ◽  
Vol 271 ◽  
Author(s):  
Krishnankutty-Nair P. Kumar ◽  
V. T. Zaspalis ◽  
F. F. M. De Mul ◽  
Klaas Keizer ◽  
Anthonie J. Burggraaf
Keyword(s):  
Thermal Stability ◽  
Raman Spectroscopy ◽  
Phase Transformation ◽  
Transformation Temperature ◽  
Rutile Phase ◽  
Phase Transformation Temperature ◽  
Supported Membranes ◽  
Beneficial Effects ◽  
The Difference ◽  
Thermal Stability Of

ABSTRACTThe beneficial effects of the support constraint on the improved thermal stability of supported titania membranes were studied by following the anatase to rutile phase transformation in supported and unsupported titania membranes. This was studied using Raman spectroscopy and XRD. Supported membranes showed a higher transformation temperature, about 150°C higher, (slower rate of transformation) compared to the unsupported ones. Unsupported membranes showed a slight thickness dependence on the phase transformation temperature, but less significant compared to the difference in phase transformation behaviour between supported and unsupported membranes of similar thicknesses.

Characterization of Ni- and Ni(Pt)-Silicide Formation on Narrow Polycrystalline Si Lines by Raman Spectroscopy

1999 ◽  
Vol 591 ◽  
Author(s):  
P. S. Lee ◽  
D. Mangelinck ◽  
K. L. Pey ◽  
J. Ding ◽  
T. Osipowicz ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Raman Spectroscopy ◽  
Raman Mapping ◽  
Silicide Formation ◽  
Nucleation Sites ◽  
The Difference ◽  
The Stability ◽  
Non Destructive ◽  
Thermal Stability Of

ABSTRACTThe formation and thermal stability of Ni- and Ni(Pt) silicide on narrow polycrystalline Si (poly-Si) lines have been investigated using the non-destructive micro-Raman technique. The presence of Ni or Ni(Pt)Si on poly-Si lines with linewidths ranging from 0.5 gtm to 0.25 μm has been monitored by a distinct Raman peak at around 215 cm−1. Ni(Pt)Si was clearly identified to be present up to a RTA temperature of 900°C on narrow poly-Si lines as compared to pure NiSi which was found only up to 750°C. Raman scattering from the 100×100 μm2 poly-Si pads showed the formation of NiSi2 at 750°C for pure Ni-salicidation and 900°C for Ni(Pt)-salicidation respectively. The difference in the stability of NiSi on the poly-Si pads and lines is discussed in terms of agglomeration, inversion and/or nucleation of NiSi2that could be due to difference in nucleation sites and/or stress. In addition, a correlation between the line sheet resistance and the presence of Ni silicide was found using micro-Raman mapping along single poly-Si lines.

scholarly journals Synthesis and photocatalytic properties of Sn–TiO2 nanomaterials

2020 ◽  
Vol 10 (01n02) ◽  
pp. 2060018
Author(s):  
E. M. Bayan ◽  
T. G. Lupeiko ◽  
L. E. Pustovaya ◽  
M. G. Volkova
Keyword(s):  
Phase Transition ◽  
Thermal Stability ◽  
Sol Gel ◽  
Rutile Phase ◽  
Photocatalytic Properties ◽  
Light Activation ◽  
X Ray ◽  
Tio2 Nanomaterials ◽  
Visible Light Activation ◽  
Thermal Stability Of

Sn-doped TiO2 nanomaterials were synthesized by sol–gel method. It was shown the phase compositions and phase transitions change with the introduction of different tin amounts (0.5–20[Formula: see text]mol.%). X-ray powder diffraction was used to study the effect of different tin amounts on the anatase–rutile phase transition. It was found that the introduction of ions increases the thermal stability of anatase modifications. The material’s photocatalytic activity was studied in reaction with a model pollutant (methylene blue) photodegradation under UV and visible light activation. The best photocatalytic properties were shown for material, which contains 5[Formula: see text]mol.% of Sn.

Capability of martensitic low transformation temperature welding consumables for increasing the fatigue strength of high strength steel joints

2020 ◽  
Vol 62 (9) ◽  
pp. 891-900
Author(s):  
Jonas Hensel ◽  
Arne Kromm ◽  
Thomas Nitschke-Pagel ◽  
Jonny Dixneit ◽  
Klaus Dilger
Keyword(s):  
Residual Stress ◽  
Phase Transformation ◽  
Fatigue Strength ◽  
High Strength Steel ◽  
Transformation Temperature ◽  
Fatigue Cracks ◽  
High Strength ◽  
Filler Material ◽  
Phase Transformation Temperature ◽  
Filler Materials

Abstract The use of low transformation temperature (LTT) filler materials represents a smart approach for increasing the fatigue strength of welded high strength steel structures apart from the usual procedures of post weld treatment. The main mechanism is based on the effect of the low start temperature of martensite formation on the stress already present during welding. Thus, compressive residual stress formed due to constrained volume expansion in connection with phase transformation become highly effective. Furthermore, the weld metal has a high hardness that can delay the formation of fatigue cracks but also leads to low toughness. Fundamental investigations on the weldability of an LTT filler material are presented in this work, including the characterization of the weld microstructure, its hardness, phase transformation temperature and mechanical properties. Special attention was applied to avoid imperfections in order to ensure a high weld quality for subsequent fatigue testing. Fatigue tests were conducted on the welded joints of the base materials S355J2 and S960QL using conventional filler materials as a comparison to the LTT filler. Butt joints were used with a variation in the weld type (DY-weld and V-weld). In addition, a component-like specimen (longitudinal stiffener) was investigated where the LTT filler material was applied as an additional layer. The joints were characterized with respect to residual stress, its stability during cyclic loading and microstructure. The results show that the application of LTT consumables leads to a significant increase in fatigue strength when basic design guidelines are followed. This enables a benefit from the lightweight design potential of high-strength steel grades.

Controllable phase transformation and improved thermal stability of nickel on tungsten substrate by electrodeposition

2019 ◽  
Vol 35 (5) ◽  
pp. 727-732
Author(s):  
Minjie Xu ◽  
Chao Hu ◽  
Haiyan Xiang ◽  
Haozi Lu ◽  
Travis Shihao Hu ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Phase Transformation ◽  
Thermal Stability Of ◽  
Tungsten Substrate

scholarly journals ALUMINA PHASE TRANSFORMATION FROM THERMAL DECOMPOSITION OF AMMONIUM ALUM SYNTHESIZED FROM KANKARA KAOLIN

2017 ◽  
Vol 36 (3) ◽  
pp. 822-828
Author(s):  
SG Bawa ◽  
AS Ahmed ◽  
PC Okonkwo
Keyword(s):  
Thermal Stability ◽  
Phase Transformation ◽  
Calcination Temperature ◽  
Starting Material ◽  
Gamma Alumina ◽  
X Ray ◽  
Alumina Phase ◽  
Ammonium Alum ◽  
Alpha Alumina ◽  
Thermal Stability Of

Thermal stability of transitional alumina phases produced from ammonium alum using Kankara kaolin as starting material was studied. Wet beneficiation method was employed to purify the starting material, after which it was calcined and dealuminated with sulphuric acid. The elemental composition, mineralogical, and physiological analyses were carried out using X-ray fluorescence (XRF), X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) techniques respectively. The ammonium alum was thermally treated by varying the calcination temperature from 700 to 1200°C and varying the time of calcination from 1 to 4 h. The formation of gamma alumina began at calcination temperature of 825°C for calcination time of 3 h, which was found to be lower than reported works of 900°C. It was found to be stable at higher temperature of 1125°C, above which phase transformation to alpha alumina was observed. The observed wide range of thermal stability of the gamma alumina phase gives it good advantage to be used for high temperature applications, such as support for catalyst promoters. Alpha alumina phase formation began at 1150°C and was fully formed at 1200°C. BET specific surface area of 166 m2/g was obtained for the gamma alumina phase which was high enough for it application as support for catalyst, catalyst and adsorbent. http://dx.doi.org/10.4314/njt.v36i3.23

Phase Transformation Temperature of NiTi Alloy Sheet Examined by Lamb Wave

2011 ◽  
Vol 320 ◽  
pp. 359-362
Author(s):  
Kai Sheng Wang ◽  
Ru Hui He ◽  
Zhi Min Zhao
Keyword(s):  
Phase Transformation ◽  
Lamb Wave ◽  
Transformation Temperature ◽  
Lamb Waves ◽  
Niti Alloy ◽  
Alloy Sheet ◽  
Phase Transformation Temperature ◽  
Wave Method

In this study, the ultrasonic PZT transducers were used for exciting and receiving Lamb waves on NiTi alloy sheet. Lamb waves were measured when the temperature of the NiTi alloy changed. Analysis on frequency spectrums of the Lamb waves was also done. Some marked changes were observed in the dependence of the waveforms and the frequency spectrums of the Lamb waves versus temperature during phase transformation of NiTi alloy. The results show that phase transformation temperature of NiTi alloy sheet may be examined by Lamb wave method.

Synthesis and Characterization of Some Functional Luminol Derivatives with Aromatic Substituted Groups

2011 ◽  
Vol 197-198 ◽  
pp. 606-609 ◽  
Author(s):  
Ti Feng Jiao ◽  
Yuan Yuan Xing ◽  
Jing Xin Zhou ◽  
Wei Wang
Keyword(s):  
Molecular Structure ◽  
Thermal Stability ◽  
Molecular Structures ◽  
Synthesis And Characterization ◽  
Functional Material ◽  
Aromatic Substituent ◽  
The Difference ◽  
Imide Group ◽  
Thermal Stability Of

Some functional luminol derivatives with aromatic substituted groups have been designed and synthesized from the reaction of the corresponding aromatic acyl chloride precursors with luminol. It has been found that depending on the size of aromatic groups, the formed luminol derivatives showed different properties, indicating distinct regulation of molecular skeletons. UV and IR data confirmed commonly the formation of imide group as well as aromatic segment in molecular structures. Thermal analysis showed that the thermal stability of luminol derivatives with p-phthaloyl segment was the highest in those derivatives. The difference of thermal stability is mainly attributed to the formation of imide group and aromatic substituent groups in molecular structure. The present results have demonstrated that the special properties of luminol derivatives can be turned by modifying molecular structures of objective compounds with proper substituted groups, which show potential application in functional material field and ECL sensor.

Sign in / Sign up

Export Citation Format

Share Document