The Influence of Reinforcing Fibers on the Morphology and Crystallization of Thermoplastic Polymer Composites

1991 ◽  
Vol 255 ◽  
Author(s):  
Ludwig Rebenfeld ◽  
Glenn P. Desio ◽  
Veronika E. Reinsch
Keyword(s):  
High Performance ◽  
Crystallization Process ◽  
Polarized Light ◽  
Fiber Surface ◽  
Weight Fraction ◽  
Degree Of Crystallinity ◽  
Surface Finishes ◽  
Reinforcing Fibers ◽  
Glass Carbon ◽  
The Degree Of Crystallinity

AbstractSemi-crystalline thermoplastic polymers are being used increasingly as matrices in high performance fiber reinforced composites. The crystallization kinetics and morphology of these polymers have been studied extensively, but relatively little attention has been given to the effects of the reinforcing fibers on the crystallization process.We have studied the effects of glass, carbon and aramid fibers on the rates of crystallization, the degree of crystallinity, and the glass transition temperature of such typical thermoplastics as poly(phenylene sulfide) and poly(ethylene terephthalate). Based on the isothermal crystallization studies using DSC, we find that, in general, reinforcing fibers increase the rates of crystallization and decrease the degree of crystallinity, the extent of these effects being dependent on the weight fraction of fiber in the composite, the specific type of fiber, and the nature of surface finishes (sizes) that may have been applied.The spherulitic morphology that develops in these polymers during the crystallization process, as characterized by polarized light microscopy, is also affected by the reinforcing fibers. In many cases, transcrystalline regions develop near the fiber surface due to nucleation effects.

scholarly journals An insight on the process–property relationships of melt spun polylactic acid fibers

2019 ◽  
Vol 89 (23-24) ◽  
pp. 4959-4966 ◽  
Author(s):  
AM Ali ◽  
HM El-Dessouky
Keyword(s):  
Polylactic Acid ◽  
High Performance ◽  
Polarized Light ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Laser Diffractometry ◽  
Wide Range ◽  
Innovative Materials ◽  
The Degree Of Crystallinity

Polylactic acid (PLA) fibers are receiving growing interest as one of the recent innovative materials being developed for various applications. The inherent biodegradability of PLA makes it highly attractive for the biomedical and health care sectors. PLA fibers need to be partially and/or highly oriented to allow high performance and readiness for a wide range of manufacturability. In this study, the structure and properties of PLA fibers, manufactured at different spinning speeds, were studied. Laser diffractometry, polarized light microscopy, differential scanning calorimetry (DSC) and X-ray diffraction (XRD) were used to determine the diameter, birefringence, molecular orientation, enthalpy and degree of crystallinity of as-spun and drawn PLA fibers. The results of DSC and XRD showed that the degree of crystallinity of the PLA fibers is significantly improved for the drawn PLA fibers compared to the as-spun fibers and leveled off in the case of changing the take-up speeds of drawn fibers.

Investigating the Effect of Nanoclay Loadings and Re-Processing on the Melting and Crystallization Behavior of PP/Clay Nanocomposites

2019 ◽  
Vol 951 ◽  
pp. 21-25
Author(s):  
Achmad Chafidz ◽  
Sholeh Ma'mun ◽  
Haryanto ◽  
Wara Dyah Pita Rengga ◽  
Prima A. Handayani ◽  
...  
Keyword(s):  
Crystallization Behavior ◽  
Crystallization Process ◽  
The Other ◽  
Degree Of Crystallinity ◽  
Clay Nanocomposites ◽  
Scanning Calorimetry ◽  
Onset Crystallization Temperature ◽  
Significant Difference ◽  
The Degree Of Crystallinity ◽  
Melting And Crystallization

In this study, PP/clay nanocomposites have been fabricated at different nanoclay loadings, i.e. 0, 5, 10, and 5 wt% for the 1stcycle and 2ndcycle (re-processing). The prepared nanocomposites were then characterized by a Differential Scanning Calorimetry (DSC) to investigate the effects of nanoclay loadings and re-processing on the melting and crystallization of the nanocomposites. The DSC results showed that the melting temperature,Tmwas not significantly affected by the nanoclay loadings and re-processing. In the other hand, the degree of crystallinity,Xcof the nanocomposites was higher than that of neat PP, but only reached a maximum at nanoclay loading of 5 wt% (i.e. 51.2% for NC-5-I and 48.3% for NC-5-II). Thereafter, theXcdecreased at higher nanoclay loadings. There was no significant difference inXcbetween 1stcycle and 2ndcycle. Additionally, in all nanocomposites samples for both cycles, there were two crystallization temperatures, i.e.Tc1andTc2. In the overall crystallization process, theTcof nanocomposites increased by 11-12°C compared to that of neat PP. Whereas, the onset crystallization temperature,Tocalso increased by approx. 13°C. Apparently, there was no significant effect of nanoclay loadings and re-processing on theTcndTocof the nanocomposites.

scholarly journals Effect of Radiation Sterilization on Alprenolol in the Solid State Studied by High-Performance Thin-Layer Chromatography

2010 ◽  
Vol 93 (3) ◽  
pp. 792-797
Author(s):  
Barbara Marciniec ◽  
Magdalena Ogrodowczyk ◽  
Anna Kwiecien′
Keyword(s):  
High Performance ◽  
Good Accuracy ◽  
High Energy ◽  
Degree Of Crystallinity ◽  
Radiation Sterilization ◽  
Good Precision ◽  
Solid Form ◽  
Layer Chromatography ◽  
Higher Doses ◽  
The Degree Of Crystallinity

Abstract The possibility of radiation sterilization of alprenolol (AL) has been studied. Irradiation of AL in solid form with a 25 kGy beam of electrons caused only an insignificant change in color that became more intense with increasing irradiation dose. Moreover, with increasing dose a decrease in pH, the content of water, and the degree of crystallinity were observed. AL in solid form was radiated with a high-energy electron beam (9.96 MeV) at doses from 25400 kGy and analyzed by HPTLC using the mobile phase methanolammonia 25 (99 + 1, v/v). Densitometric analysis was carried out directly from chromatograms at 270 nm. The applied method was validated and characterized by good precision (RSD = 3.95); good accuracy (80 level 100.15, 100 level 99.99, and 120 level 104.44); and low LOD (LOD = 0.52 g/zone and LOQ = 1.55 g/zone). Chromatograms recorded for samples irradiated at the doses of 25 kGy were unchanged, but at higher doses (100400 kGy) additional peaks corresponding to the radiodegradation products appeared (Rf = 0.24 and Rf = 0.40). The decrease in the concentration of AL was proportional to the applied radiation dose, and for 400 kGy the concentration of AL was 90.23. The calculated radiolytic yield of the radiodegradation process was G(AL) = 7.12 107 mol/J.

Effects of initial crystallization process on piezoelectricity of PVDF-HFP films

2015 ◽  
Vol 35 (5) ◽  
pp. 451-461 ◽  
Author(s):  
Bin Hu ◽  
Ning Hu ◽  
Liangke Wu ◽  
Feng Liu ◽  
Yaolu Liu ◽  
...  
Keyword(s):  
Crystallization Process ◽  
Vinylidene Fluoride ◽  
Degree Of Crystallinity ◽  
Slow Cooling ◽  
Poly Vinylidene Fluoride ◽  
Cooling Speed ◽  
Solution Casting Method ◽  
Heating Pattern ◽  
The Degree Of Crystallinity ◽  
Initial Crystallization Temperature

Abstract The effects of some important factors in the initial crystallization process of the solution casting method on the piezoelectricity of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) films were extensively explored. The experimental results revealed that there is an optimal initial crystallization temperature at around 90°C. The slow cooling speed can moderately enhance the degree of crystallinity. The most important finding was that a bilayer crystalline structure caused by an asymmetrical heating pattern can enhance the formation of packed micro-fibrillar morphologies after drawing. These three points can increase the piezoelectricity of the PVDF-HFP films, indicating the increase of the extended-chain crystals (β-phase).

Study of Transcrystallization in Polymer Composites

1989 ◽  
Vol 170 ◽  
Author(s):  
Benjamin S. Hsiao ◽  
J. H. Eric
Keyword(s):  
Thermal Conductivity ◽  
Free Energy ◽  
Carbon Fiber ◽  
Plasma Treatment ◽  
Polymer Composites ◽  
High Performance ◽  
Interfacial Strength ◽  
Fiber Surface ◽  
Semicrystalline Polymers ◽  
First Case

AbstractTranscrystallization of semicrystalline polymers, such as PEEK, PEKK and PPS, in high performance composites has been investigated. It is found that PPDT aramid fiber and pitch-based carbon fiber induce a transcrystalline interphase in all three polymers, whereas in PAN-based carbon fiber and glass fiber systems, transcrystallization occurs only under specific circumstances. Epitaxy is used to explain the surface-induced transcrystalline interphase in the first case. In the latter case, transcrystallization is probably not due to epitaxy, but may be attributed to the thermal conductivity mismatch. Plasma treatment on the fiber surface showed a negligible effect on inducing transcrystallization, implying that surface-free energy was not important. A microdebonding test was adopted to evaluate the interfacial strength between the fiber and matrix. Our preliminary results did not reveal any effect on the fiber/matrix interfacial strength of transcrystallinity.

scholarly journals Polarization-sensitive photodetectors based on three-dimensional molybdenum disulfide (MoS2) field-effect transistors

Nanophotonics ◽  
2020 ◽  
Vol 9 (16) ◽  
pp. 4719-4728
Author(s):  
Tao Deng ◽  
Shasha Li ◽  
Yuning Li ◽  
Yang Zhang ◽  
Jingye Sun ◽  
...  
Keyword(s):  
Molybdenum Disulfide ◽  
Field Effect ◽  
High Performance ◽  
Field Effect Transistors ◽  
Three Dimensional ◽  
Polarized Light ◽  
Optical Field ◽  
Two Dimensional ◽  
Polarization Ratio ◽  
Two Dimensional Materials

AbstractThe molybdenum disulfide (MoS2)-based photodetectors are facing two challenges: the insensitivity to polarized light and the low photoresponsivity. Herein, three-dimensional (3D) field-effect transistors (FETs) based on monolayer MoS2 were fabricated by applying a self–rolled-up technique. The unique microtubular structure makes 3D MoS2 FETs become polarization sensitive. Moreover, the microtubular structure not only offers a natural resonant microcavity to enhance the optical field inside but also increases the light-MoS2 interaction area, resulting in a higher photoresponsivity. Photoresponsivities as high as 23.8 and 2.9 A/W at 395 and 660 nm, respectively, and a comparable polarization ratio of 1.64 were obtained. The fabrication technique of the 3D MoS2 FET could be transferred to other two-dimensional materials, which is very promising for high-performance polarization-sensitive optical and optoelectronic applications.

scholarly journals Estimation of the Age of Architectural Heritage Objects by Microstructural Changes of Calcite in Lime Mortars of Ancient Brickwork and Masonry

Buildings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 240
Author(s):  
Vladimir Kotlyar ◽  
Victoria Pishchulina ◽  
Alexey N. Beskopylny ◽  
Besarion Meskhi ◽  
Yury Popov ◽  
...  
Keyword(s):  
18Th Century ◽  
Degree Of Crystallinity ◽  
Architectural Heritage ◽  
Natural Conditions ◽  
Relative Age ◽  
Lime Mortars ◽  
Powder Samples ◽  
Diffraction Patterns ◽  
Cultural Monuments ◽  
The Degree Of Crystallinity

Determining the age of ancient architectural and cultural monuments is a significant scientific problem. An approach based on the transformation of portlandite into calcite and subsequent recrystallization of calcite is considered, which allows for estimating the relative age of ancient brickworks for local groups of historic buildings based on the results of diffraction studies of powder samples of carbonate mortars and measurements of samples with a known age. This article presents the results of the study of lime mortars of ancient brickwork. Under natural conditions, the process of transformation of portlandite into calcite takes from 100 to 200 years. The rate of this process is influenced by temperature, humidity, peculiarities of interaction with carbon dioxide contained in the air, etc. Examples show that portlandite is completely transformed into calcite in masonry mortars of the 18th century and that portlandite is not found in older mortars. It was determined that after the transformation of portlandite into calcite, an increase in the degree of recrystallization of calcite is observed, which manifests itself in powder diffraction patterns in the relative broadening of the diffraction peak of calcite hkl 104. In a detailed study, an estimate of the peak width at half maximum (FWHM) associated with the degree of crystallinity is effective. The actual data are given, which show that in older lime mortars the degree of recrystallization of calcite is higher than in younger ones. This fact makes it possible to indirectly determine the relative age of brickwork and masonry of various buildings of architectural heritage, which is especially relevant for the objects with the use of lime mortars of the northern provinces of the Byzantine Oecumene and other periods of various cultures.

scholarly journals Crystallization Behavior and Mechanical Properties of Poly(ε-caprolactone) Reinforced with Barium Sulfate Submicron Particles

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2368
Author(s):  
Hegoi Amestoy ◽  
Paul Diego ◽  
Emilio Meaurio ◽  
Jone Muñoz ◽  
Jose-Ramon Sarasua
Keyword(s):  
Barium Sulfate ◽  
Thermal Studies ◽  
Polarized Light ◽  
Optical Microscope ◽  
Submicron Particles ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Nucleation Effect ◽  
Crystal Fraction ◽  
Light Optical Microscope

Poly(ε-caprolactone) (PCL) was mixed with submicron particles of barium sulfate to obtain biodegradable radiopaque composites. X-ray images comparing with aluminum samples show that 15 wt.% barium sulfate (BaSO4) is sufficient to present radiopacity. Thermal studies by differential scanning calorimetry (DSC) show a statistically significant increase in PCL degree of crystallinity from 46% to 52% for 25 wt.% BaSO4. Non-isothermal crystallization tests were performed at different cooling rates to evaluate crystallization kinetics. The nucleation effect of BaSO4 was found to change the morphology and quantity of the primary crystals of PCL, which was also corroborated by the use of a polarized light optical microscope (PLOM). These results fit well with Avrami–Ozawa–Jeziorny model and show a secondary crystallization that contributes to an increase in crystal fraction with internal structure reorganization. The addition of barium sulfate particles in composite formulations with PCL improves stiffness but not strength for all compositions due to possible cavitation effects induced by debonding of reinforcement interphase.

scholarly journals Preparation and Characterization of Talc Filled Thermoplastic Polyurethane/Polypropylene Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Emi Govorčin Bajsić ◽  
Vesna Rek ◽  
Ivana Ćosić
Keyword(s):  
Thermal Properties ◽  
Thermoplastic Polyurethane ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Polypropylene Blends ◽  
Pp Blends ◽  
The Degree Of Crystallinity ◽  
Better Than

The effect of the addition of talc on the morphology and thermal properties of blends of thermoplastic polyurethane (TPU) and polypropylene (PP) was investigated. The blends of TPU and PP are incompatible because of large differences in polarities between the nonpolar crystalline PP and polar TPU and high interfacial tensions. The interaction between TPU and PP can be improved by using talc as reinforcing filler. The morphology was observed by means of scanning electron microscopy (SEM). The thermal properties of the neat polymers and unfilled and talc filled TPU/PP blends were studied by using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The addition of talc in TPU/PP blends improved miscibility in all investigated TPU/T/PP blends. The DSC results for talc filled TPU/PP blends show that the degree of crystallinity increased, which is due to the nucleating effect induced by talc particles. The reason for the increased storage modulus of blends with the incorporation of talc is due to the improved interface between polymers and filler. According to TGA results, the addition of talc enhanced thermal stability. The homogeneity of the talc filled TPU/PP blends is better than unfilled TPU/PP blends.

Sign in / Sign up

Export Citation Format

Share Document