LPE Growth and Characterization of InAsSbP/In1-x GaxAs1-ySby /InAsSbP (X≥O,Y≥O) Heterostructures for Long Wavelength ( λ>3μm) Leds and Lasers.

1990 ◽  
Vol 216 ◽  
Author(s):  
M. Aydaraliev ◽  
T.S. Argunova ◽  
N.V. Zotova ◽  
S.A. Karandashov ◽  
R.N. Kutt ◽  
...  
Keyword(s):  
Plastic Deformation ◽  
Dislocation Density ◽  
Band Gap ◽  
Deformation Process ◽  
Elevated Temperatures ◽  
Substrate Thickness ◽  
Misfit Dislocations ◽  
Long Wavelength ◽  
Plastic Deformation Process

The band gap of InAsSbP and InGaAsSb alloys enriched with InAs correspods to the spectral range 2.5 - 5 μm which make possible to manufacture LEDs and detectors for the second atmosphere window. Elevated hardness (see Fig.1a ) and small plasticity of the alloys results in an inversed plastic deformation process during LPE growth of InAsSbP (InGaAsSb) on InAs substrate.That is when growing graded( grad a ≈5*10−8 epilayers at elevated temperatures ( 680 - 720° C ) misfit dislocations are formed throughout the entire substrate thickness (C). Simultaneously with increasing dislocation density in InAs ( curves 1,3 ), the curvature of the structure increased within æ = 0.02-0.2 cm−1.

scholarly journals A Dislocation-Based Theory for the Deformation Hardening Behavior of DP Steels: Impact of Martensite Content and Ferrite Grain Size

2010 ◽  
Vol 2010 ◽  
pp. 1-16 ◽  
Author(s):  
Yngve Bergström ◽  
Ylva Granbom ◽  
Dirk Sterkenburg
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Deformation Process ◽  
Volume Fraction ◽  
High Energy ◽  
Martensite Content ◽  
Plastic Deformation Process ◽  
Deformation Hardening ◽  
Dp Steels ◽  
Ferrite Grain Size

A dislocation model, accurately describing the uniaxial plastic stress-strain behavior of dual phase (DP) steels, is proposed and the impact of martensite content and ferrite grain size in four commercially produced DP steels is analyzed. It is assumed that the plastic deformation process is localized to the ferrite. This is taken into account by introducing a nonhomogeneity parameter, f(ε), that specifies the volume fraction of ferrite taking active part in the plastic deformation process. It is found that the larger the martensite content the smaller the initial volume fraction of active ferrite which yields a higher initial deformation hardening rate. This explains the high energy absorbing capacity of DP steels with high volume fractions of martensite. Further, the effect of ferrite grain size strengthening in DP steels is important. The flow stress grain size sensitivity for DP steels is observed to be 7 times larger than that for single phase ferrite.

Influence of Compressive Torsion Processing Temperature on Microstructure Refinement and Property of Aluminum Alloy

2007 ◽  
Vol 26-28 ◽  
pp. 133-136 ◽  
Author(s):  
Shotaro Tahara ◽  
Yuji Kume ◽  
Makoto Kobashi ◽  
Naoyuki Kanetake
Keyword(s):  
Plastic Deformation ◽  
Deformation Process ◽  
Large Strain ◽  
Tensile Elongation ◽  
Total Elongation ◽  
Work Piece ◽  
Processing Temperature ◽  
Microstructure Refinement ◽  
Plastic Deformation Process ◽  
Eutectic Si

A compressive torsion processing (CTP) was applied to hypereutectic Al-Si alloy in order to raise ductility and formability by microstructure refinement of the alloy. The CTP is a unique severe plastic deformation process and it can easily apply large strain to a work piece without change in shape. In the present work, influence of compressive torsion processing temperature on microstructure refinement and tensile property of hypereutectic Al-Si alloy is dealt with. When the CTP was applied on the Al-Si alloy, primary and eutectic Si particles were refined more effectively at lower processing temperature. Total tensile elongation of CTPed alloy was four times as large as that of non CTPed one. Distribution of the total elongation was quite uniform in the whole CTPed specimen.

scholarly journals Deformation of Second Phase Particles in Al Alloy Using Severe Plastic Deformation Process

Materia Japan ◽  
2003 ◽  
Vol 42 (12) ◽  
pp. 863-863 ◽  
Author(s):  
Keiichiro Ohishi ◽  
Takeshi Fujita ◽  
Kunihiro Ohashi ◽  
Kenji Kaneko ◽  
Zenji Horita
Keyword(s):  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Deformation Process ◽  
Al Alloy ◽  
Second Phase ◽  
Severe Plastic Deformation Process ◽  
Plastic Deformation Process ◽  
Second Phase Particles

THEORETICAL AND PRACTICAL BASIS OF ROLLED PRODUCTS

2021 ◽  
Vol 2 (1) ◽  
pp. 55-60
Author(s):  
Bahodir Qurbanovich Tilabov ◽  
◽  
Saidabbos Ikromovich Isaev ◽  
Jamshid Abdurazzokovich Sherbo’taev ◽  
Ikhtiyor Chorievich Zhurakulov
Keyword(s):  
Plastic Deformation ◽  
Deformation Process ◽  
Rolled Steel ◽  
Plastic Deformation Process ◽  
Hardening Treatment ◽  
Microstructure Parameters ◽  
Metal Products ◽  
Steel Hardening ◽  
Hardening Heat Treatment

The article presents the theoretical and practical basis for the production of rolled products in the conditions of a metallurgical plant. The processes of plastic deformation of bodies between rotating drive rolls are shown. The main results of research on rolled products made of rolled steel are presented. The chemical composition, mechanical properties, macro -and microstructure parameters, and strengthening treatments of locally produced rolled steel were studied. It is shown that after hardening treatment, the strength increases and the quality of rolled products improves.Keywords:composition and properties of rolled metal products, plastic deformation process, rotating drive rollers, rolled body, rolled steel, hardening heat treatment, hardness, macro-and microstructure, performance and quality of finished products

TEM Characterization of a 7042 Aluminum FSW Joint

2012 ◽  
Vol 186 ◽  
pp. 331-334
Author(s):  
Mateusz Kopyściański ◽  
Stanislaw Dymek ◽  
Carter Hamilton
Keyword(s):  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Dislocation Density ◽  
Severe Plastic Deformation ◽  
Base Material ◽  
Friction Stir ◽  
Tem Characterization ◽  
Equiaxed Grains

This research characterizes the changes in microstructure that occur in friction stir welded extrusions of a novel 7042 aluminum alloy. Due to the presence of scandium the base material preserved the deformation microstructure with elongated grains and fairly high dislocation density. The temperature increase with simultaneous severe plastic deformation occurring during friction stir welding induced significant changes in the microstructure within the weld and its vicinity. The weld center (stir zone) was composed of fine equiaxed grains with residual dislocations and a modest density of small precipitates compared to the neighbouring thermomechanically and heat affected zones where the density of small precipitates was much higher.

Sign in / Sign up

Export Citation Format

Share Document