The Use of Partial-Replenishment Tests in Modeling the Leach behavior of Glasses

1990 ◽  
Vol 212 ◽  
Author(s):  
Aa. Barkatt ◽  
S. A. Olszowka ◽  
W. Sousanpour ◽  
T. Choudhury ◽  
Y. Guo ◽  
...  
Keyword(s):  
Simple Model ◽  
Residence Time ◽  
Time Sampling ◽  
Test Results ◽  
Approach To Equilibrium ◽  
First Order ◽  
Short Period ◽  
Two Parameters ◽  
Leach Behavior

ABSTRACTThe partial-replenishment test can be an important tool in exploring the long-term leach behavior of glasses. In order to demonstrate the use of partial-replenishment test data in modeling, experiments were conducted which show that after a relatively short period test results become largely independent of exchange interval and volume exchange fraction. The results can be characterized by the ratio between these two parameters, which corresponds to the residence time. Sampling of the leachates during a given exchange interval shows that leachate concentrations quickly recover following the exchange, and that this recovery can be satisfactorily described using a simple model based on first-order approach to equilibrium at the silica saturation level.

Characterization and analysis of groundwater recharge through tritium measurements

2021 ◽  
Author(s):  
Chiara Telloli ◽  
Antonietta Rizzo ◽  
Stefano Salvi ◽  
Alberto Ubaldini
Keyword(s):  
Residence Time ◽  
Anthropogenic Activities ◽  
Tritiated Water ◽  
Rain Water ◽  
Department Of Energy ◽  
Human Consumption ◽  
Anthropogenic Contamination ◽  
Average Value ◽  
Short Period ◽  
Two Parameters

<p>The August, 2 2017 Decree, which standardized the health protection requirements from the presence of radioactive substances in the waters intended for human consumption, provides for the obligation to verify the value of two parameters relating to the radioactivity content in drinking water: the concentration of tritium, which must be less than 850 UT (unit of tritium), and the total indicative dose, related to ingestion, which must be less than 0.1 mSv / year.</p><p>Tritium atoms produced in the atmosphere, by combination with oxygen in the air, tritiated water (HTO) which, having greater molecular mass than the H2O molecule, has a shorter residence time in the atmosphere from which it tends to be removed with precipitation. The short periods of residence in the atmosphere and the short period of decay mean that the concentrations of tritium in the rains are low and almost constant, as there is a balance between the speed of formation, the removal by the rains and the total quantity of natural tritium in the environment which is ∼ 70 × 106 Ci (US Department of Energy, 2002). This means that in groundwater with a long residence time in subsoil, infiltrated before 1950 (nuclear test period), the concentration of tritium is below the analytical detection limit.</p><p>In 1960, rainwater had an abnormal concentration (due to the emission into the atmosphere following nuclear tests) corresponding to an average value of 1000 UT. In the subsoil the decay of tritium produces its continuous loss which, in the absence of rainwater recharge and without the compensation of new atmospheric inputs, causes a decrease. To date, in the absence of any infiltration, this water would contain 35 UT.</p><p>Given that waters with over 50 years generally have dilution factors from 10 to 20 times with tritium-free fossil water, today we expect, due to mixing, detectable UT values but lower than 4. Aquifer values greater than 9 UT would therefore be related to recent anthropogenic recharge or surface percolation factors.</p><p>In the case of recharge with rain water rich in tritium, the concentration reflects the balance between the loss due to decay and the supply of rain water enriched with tritium. Based on the abundance of tritium, in the absence of sources of anthropogenic contamination it is possible to establish the average age of groundwater under the age of 50. This data is very important, because by analyzing the concentrations of tritium present in groundwater it is possible to trace the age of the aquifer and / or define if the aquifer is polluted by anthropogenic activities.</p><p>ENEA's Environmental Traceability and Radiometry Laboratory is at the forefront of the analysis of radioisotopes in the environment, including low-concentration of tritium analyzes. In this regard, an activity with ARPAV of Treviso was started for the determination and evaluation of the concentrations of tritium found in groundwater samples of the area around the city of Treviso.</p>

Parents' long-term adjustment to the genetic test results of minors at risk for Long QT Syndrome

2004 ◽  
Author(s):  
K. S. W. H. Hendriks ◽  
F. J. M. Grosfeld ◽  
A. A. M. Wilde ◽  
J. van den Bout ◽  
I. M. van Langen ◽  
...  
Keyword(s):  
At Risk ◽  
Long Qt Syndrome ◽  
Genetic Test ◽  
Test Results ◽  
Long Qt ◽  
Genetic Test Results ◽  
Qt Syndrome

The Implementation Of Make A-Match Model In Social Science Learning To Improve Student Learning Outcomes In Class IV SDN 115 Manado

2019 ◽  
Vol Volume 2 Nomor 2 ◽  
Keyword(s):  
Social Science ◽  
Learning Outcomes ◽  
Teaching And Learning ◽  
Science Learning ◽  
Design Activity ◽  
Test Results ◽  
Match Model ◽  
Fourth Grade Students ◽  
Improve Student Learning

There is a tendency in the education field today to return to the idea that children will learn better if the environment is created naturally. Learning will be more meaningful if children "experience" themselves what they are learning, not 'knowing' it. Target-oriented learning of material mastery proves to be successful in short-term 'remembering' competitions, but fails to equip children to solve problems in long-term life. The problems that would to be studied in this study are: (a) how is the improvement of Social Science learning outcomes by applying the Make A-Match Model to it? (b) how does the Make A-Match Model apply towards the learning motivation? The objectives of this study are: (a) want to know the improvement in Social Science learning achievement after the implemetation of the Make A-Match Model. (b) want to know the effect of Make A-Match Model towards students’ motivation of the subject after it is applied. This research is used two rounds of action research. In each round consists of four stages, namely: design, activity and observation, reflection and revision. The target of this research is the fourth grade students of Mongodow. The data obtained in the form of formative test results, observation sheets of teaching and learning activities. From the results of analysts obtained student achievement has increased from cycle I to cycle II namely, cycle I (65%), cycle II (83%). The conclusion of this research is the Make A-Match Model of Social Science learning could positively influence the motivation of learning of central students, and this learning model could be used as an alternative to Social Science learning.

Long Term Field Test Results of Experimental EPDM and PUF Roofing

1990 ◽  
Author(s):  
David M. Bailey ◽  
Stuart D. Foltz ◽  
Myer J. Rosenfield
Keyword(s):  
Field Test ◽  
Test Results ◽  
Term Field

Photocatalytic Discolouration of Solutions of Reactive Dyes in the Presence of H2O2

1995 ◽  
Vol 30 (1) ◽  
pp. 53-60 ◽  
Author(s):  
Deng Nansheng ◽  
Tian Shizhong ◽  
Xia Mei
Keyword(s):  
Photochemical Reaction ◽  
Uv Light ◽  
Reactive Dyes ◽  
Solar Light ◽  
Rate Equations ◽  
Oh Radical ◽  
Test Results ◽  
Dye Molecules ◽  
First Order ◽  
Dye Solutions

Abstract Tests for the photocatalytic degradation of solutions of three reactive dyes, Red M-5B, Procion Blue MX-R and Procion Black H-N, in the presence of H2O2 were carried out. When the solutions of the three reactive dyes were irradiated by UV or solar light, the colour of the solutions disappeared gradually. A statistical analysis of the test results indicated a linear relation between the concentration of dyes and the time of irradiation. The discolouration reaction of the solutions was of the first order. Rate equations for the discolouration reactions of dye solutions were developed. The dark reactions or the dye solutions containing H2O2 were very slow, illustrating that the photochemical reaction played a very important role. It was demonstrated that UV light and solar light (300 to 380 nm) photolyzes the HO and that the resulting OH radical reacts with the dye molecules and destroys the chromophore.

scholarly journals Management of a Mycotic Aneurysm in a Patient with COVID-19: A Case Report

Medicina ◽  
2021 ◽  
Vol 57 (6) ◽  
pp. 620
Author(s):  
Muzammil H. Syed ◽  
Mark Wheatcroft ◽  
Danny Marcuzzi ◽  
Hooman Hennessey ◽  
Mohammad Qadura
Keyword(s):  
Abdominal Aortic Aneurysm ◽  
Aortic Aneurysm ◽  
Stent Graft ◽  
Mycotic Aneurysm ◽  
Neurological Deficits ◽  
Endovascular Stent ◽  
Endovascular Stents ◽  
Abdominal Aortic ◽  
Short Period

The aim of this paper is to share our experience in managing a patient with Klebsiella pneumoniae mycotic abdominal aortic aneurysm who was also infected with COVID-19. A 69-year-old male was transferred to our hospital for the management of an infra-renal mycotic abdominal aortic aneurysm. During his hospital course, the patient contracted severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). He was intubated due to respiratory distress. Over a short period, his mycotic aneurysm increased in size from 2.5 cm to 3.9 cm. An emergency repair of his expanding aneurysm was achieved using our previously described protocol of coating endovascular stents with rifampin. The patient was managed with a rifampin-coated endovascular stent graft without any major complications. Postoperatively, the patient did not demonstrate any neurological deficits nor any vascular compromise. He remained afebrile during his postoperative course and was extubated sometime thereafter. He was then transferred to the ward for additional monitoring prior to his discharge to a rehab hospital while being on long-term antibiotics. During his hospital stay, he was monitored with serial ultrasounds to ensure the absence of abscess formation, aortic aneurysm growth or graft endoleak. At 6 weeks after stent graft placement, he underwent a CT scan, which showed a patent stent graft, with a residual sac size of 2.5 cm without any evidence of abscess or endoleak. Over a follow-up period of 180 days, the patient remained asymptomatic while remaining on long-term antibiotics. Thus, in patients whose surgical risk is prohibitive, endovascular stent grafts can be used as a bridge to definitive surgical management.

scholarly journals An unusually low density ultra-short period super-Earth and three mini-Neptunes around the old star TOI-561

2020 ◽  
Author(s):  
G Lacedelli ◽  
L Malavolta ◽  
L Borsato ◽  
G Piotto ◽  
D Nardiello ◽  
...  
Keyword(s):  
Transit Time ◽  
Time Variation ◽  
Planetary System ◽  
Radial Velocities ◽  
Low Density ◽  
Outer Planets ◽  
Short Period ◽  
The Stability

Abstract Based on HARPS-N radial velocities (RVs) and TESS photometry, we present a full characterisation of the planetary system orbiting the late G dwarf After the identification of three transiting candidates by TESS, we discovered two additional external planets from RV analysis. RVs cannot confirm the outer TESS transiting candidate, which would also make the system dynamically unstable. We demonstrate that the two transits initially associated with this candidate are instead due to single transits of the two planets discovered using RVs. The four planets orbiting TOI-561 include an ultra-short period (USP) super-Earth (TOI-561 b) with period Pb = 0.45 d, mass Mb = 1.59 ± 0.36 M⊕ and radius Rb = 1.42 ± 0.07 R⊕, and three mini-Neptunes: TOI-561 c, with Pc = 10.78 d, Mc = 5.40 ± 0.98 M⊕, Rc = 2.88 ± 0.09 R⊕; TOI-561 d, with Pd = 25.6 d, Md = 11.9 ± 1.3 M⊕, Rd = 2.53 ± 0.13 R⊕; and TOI-561 e, with Pe = 77.2 d, Me = 16.0 ± 2.3 M⊕, Re = 2.67 ± 0.11 R⊕. Having a density of 3.0 ± 0.8 g cm−3, TOI-561 b is the lowest density USP planet known to date. Our N-body simulations confirm the stability of the system and predict a strong, anti-correlated, long-term transit time variation signal between planets d and e. The unusual density of the inner super-Earth and the dynamical interactions between the outer planets make TOI-561 an interesting follow-up target.

scholarly journals Heatwaves in Kenya 1987–2016: Facts from CHIRTS High Resolution Satellite Remotely Sensed and Station Blended Temperature Dataset

Atmosphere ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 37
Author(s):  
Martial Amou ◽  
Amatus Gyilbag ◽  
Tsedale Demelash ◽  
Yinlong Xu
Keyword(s):  
High Resolution ◽  
Adaptation Strategies ◽  
Reference Period ◽  
The West ◽  
Tana River ◽  
Short Period ◽  
The World ◽  
Northern Side ◽  
Data Source

As global temperatures continue to rise unabated, episodes of heat-related catastrophes across the world have intensified. In Kenya, heatwave phenomena and their associated impacts are ignored and neglected due to several reasons, including unreliable and inconsistent weather datasets and heatwave detection metrics. Based on CHIRTS satellite infrared estimates and station blended temperature, this study investigated the spatiotemporal distribution of the heatwave events over Kenya during 1987–2016 using the Heatwave Magnitude Index daily (HWMId). The results showed that contrary to the absence of heatwave records in official national and international disaster database about Kenya, the country experienced heatwaves ranging from less severe (normal) to deadly (super-extreme) between 1987 and 2016. The most affected areas were located in the eastern parts of the country, especially in Garissa and Tana River, and in the west-northern side around the upper side of Turkana county. It was also found that the recent years’ heatwaves were more severe in magnitude, duration, and spatial extent. The highest magnitude of the heatwaves was recorded in 2015 (HWMId = 22.64) while the average over the reference period is around 6. CHIRTS and HWMId were able to reveal and capture most critical heatwave events over the study period. Therefore, they could be used respectively as data source and detection metrics, for heatwaves disaster emergency warning over short period as well as for long-term projection to provide insight for adaptation strategies.

Long-term efficacy of a short period of taping followed by an exercise program in a cohort of patients with patellofemoral pain syndrome

2011 ◽  
Vol 31 (3) ◽  
pp. 535-539 ◽  
Author(s):  
Marco Paoloni ◽  
Giancarlo Fratocchi ◽  
Massimiliano Mangone ◽  
Massimiliano Murgia ◽  
Valter Santilli ◽  
...  
Keyword(s):  
Exercise Program ◽  
Pain Syndrome ◽  
Patellofemoral Pain Syndrome ◽  
Patellofemoral Pain ◽  
Term Efficacy ◽  
Short Period

Mathematical modeling of fluid movement inside the eyeball during intravitreal injection

2021 ◽  
pp. 106-109
Author(s):  
D.V. Lipatov ◽  
◽  
S.A. Skladchikov ◽  
N.P. Savenkova ◽  
V.V. Novoderezkin ◽  
...  
Keyword(s):  
Mathematical Modeling ◽  
Mathematical Model ◽  
Residence Time ◽  
Complex Structure ◽  
Posterior Vitreous Detachment ◽  
Vitreous Body ◽  
Complete Removal ◽  
Intravitreal Injections ◽  
The World

Background. The avalanche-like growth of intravitreal injections in the world has significantly increased interest in the hemodynamics of the processes that occur in the eye when a drug is injected into the vitreous cavity. Every year, the number of intravitreally used drugs and promising areas in which they can be used is growing. This also applies to the creation of new combined medicines and the development of drugs with a long-term therapeutic effect. Aims. Create mathematical model of eyeball to evaluate the movement of the drug substance in it; to estimate the time of the drug's presence in the eye cavity before its complete removal, to characterize the ways of its removal from the eye cavity; to assess the significance of posterior vitreous detachment during the time when the drug is present in the eye cavity; to evaluate the effect on the hydrodynamics of the depth of drug administration. Results. When the drug is administered closer to the center of the eyeball, its residence time increases in comparison with the parietal administration. With a complete posterior detachment of the vitreous body, the time of finding the drug in the eye is prolonged compared to its absence. The obtained results of mathematical modeling of the movement of the drug administered intravitreally cannot be mechanically transferred to the human eye, due to the more complex structure of the latter. Key words: intravitreal injections, vitreous body, mathematic computing.

Sign in / Sign up

Export Citation Format

Share Document