Microstructures, Grain Boundaries and Superplasticity in Fine Grained Ceramics

1990 ◽  
Vol 196 ◽  
Author(s):  
C. Carry
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Boundary Segregation ◽  
Boundary Structure ◽  
Fine Grained ◽  
Chemical Effects ◽  
Liquid Phases ◽  
Grain Boundary Structure ◽  
Wide Range ◽  
Points Of View

ABSTRACTDeformation studies in compression and in tension have clearly shown evidence for superplasticity for a wide range of fine grained ceramics from both macroscopic and microscopic points of view. The main purpose of this paper is to focus attention on chemical effects in ceramic grain boundaries which can lead to a great variety of behavior. Grain boundary segregation or precipitation, residual impurities or doping elements, and glassy or liquid phases at grain boundaries can strongly affect the macroscopic flow properties of superplastic fine grained ceramics. Some microstructural and grain boundary features, mainly in two oxide materials (alumina and yttria doped zirconia), are analyzed, compared, and discussed in connection with their observed superplastic behavior. Special attention is devoted to the relation between the overall chemistry of the materials (impurities and doping elements) and to the grain boundary structure and chemistry (segregation, precipitation, intergranular phases). Some consequences and implications on the tailoring of ceramic microstructures for superplasticity are discussed. In addition, some recent hot forming and hot bonding experiments are also reported.

Structural and Mechanical Properties of Nanophase Ni: A Molecular-Dynamics Study of the Influence of Grain-Boundary Structure on Elastic and Plastic Behavior

1997 ◽  
Vol 492 ◽  
Author(s):  
H. Van Swygenhoven ◽  
M. Spaczér ◽  
A. Caro
Keyword(s):  
Molecular Dynamics ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Diffusion Mechanism ◽  
Distribution Functions ◽  
Boundary Structure ◽  
Plastic Behavior ◽  
Self Diffusion ◽  
Common Neighbour ◽  
Grain Boundary Structure

ABSTRACTMolecular dynamics computer simulations of high load plastic deformation at temperatures up to 500K of Ni nanophase samples with mean grain size of 5 nm are reported. Two types of samples are considered: a polycrystal nucleated from different seeds, each having random location and random orientation, representing a sample with mainly high angle grain boundaries, and polycrystals with seeds located at the same places as before, but with a limited missorientation representing samples with mainly low angle grain boundaries. The structure of the grain boundaries is studied by means of pair distribution functions, coordination number, atom energetics, and common neighbour analysis. Plastic behaviour is interpreted in terms of grain-boundary viscosity, controlled by a self diffusion mechanism at the disordered interface activated by thermal energy and stress.

Systematic Study of Grain Boundary Structure and Chemical Analysis of [100] and [111] Tilt Grain Boundaries in Yttria-Stabilized Zirconia

2004 ◽  
Vol 10 (S02) ◽  
pp. 304-305 ◽  
Author(s):  
James P Buban ◽  
Katsuyuki Matsunaga ◽  
Takahisa Yamamoto ◽  
Yuichi Ikuhara
Keyword(s):  
Chemical Analysis ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Systematic Study ◽  
Yttria Stabilized Zirconia ◽  
Boundary Structure ◽  
Stabilized Zirconia ◽  
Grain Boundary Structure

Extended abstract of a paper presented at Microscopy and Microanalysis 2004 in Savannah, Georgia, USA, August 1–5, 2004.

GRAIN BOUNDARIES: PHASE TRANSITIONS AND CRITICAL PHENOMENA

1991 ◽  
Vol 05 (19) ◽  
pp. 2989-3028 ◽  
Author(s):  
E.I. RABKIN ◽  
L.S. SHVINDLERMAN ◽  
B.B. STRAUMAL
Keyword(s):  
Phase Transitions ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Critical Phenomena ◽  
External Surface ◽  
Theoretical Models ◽  
Boundary Structure ◽  
Boundary Phase ◽  
Recent Experimental Data ◽  
Grain Boundary Structure

Recent theories of grain boundary structure have been reviewed briefly. The possibility of existence of the same variety of phase transitions on grain boundaries as that on the crystal external surface has been demonstrated. Recent experimental data and theoretical models concerning grain boundary phase transitions are critically analysed. Grain boundary phase transitions connected with the formation of thin disordered layers on the boundary (prewetting, premelting) are particularly distinguished. Results of recent indirect experiments, which may be treated in terms of prewetting and premelting, have been reviewed. Experimentally observed critical phenomena in the vicinity of the prewetting transition on the tin-germanium interphase boundary have been discussed in terms of the critical exponents theory. Some ideas regarding directions of further research are presented.

Observations and implications of grain boundary dislocation networks in high-angle YBa2Cu3O7−δ grain boundaries

1990 ◽  
Vol 5 (5) ◽  
pp. 919-928 ◽  
Author(s):  
S. E. Babcock ◽  
D. C. Larbalestier
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Weak Link ◽  
Coincidence Site Lattice ◽  
Boundary Structure ◽  
High Angle ◽  
Grain Boundary Structure ◽  
Transmission Electron ◽  
Means Of Transmission ◽  
Regular Networks

Regular networks of localized grain boundary dislocations (GBDs) have been imaged by means of transmission electron microscopy in three different types of high-angle grain boundaries in YBa2Cu3O7-δ, implying that these boundaries possess ordered structures upon which a significant periodic strain field is superimposed. The occurrence of these GBD networks is shown to be consistent with the GBD/Structural Unit and Coincidence Site Lattice (CSL)/Near CSL descriptions for grain boundary structure. Thus, these dislocations appear to be intrinsic features of the boundary structure. The spacing of the observed GBDs ranged from ∼10 nm to ∼100 nm. These GBDs make the grain boundaries heterogeneous on a scale that approaches the coherence length and may contribute to their weak-link character by producing the “superconducting micro-bridge” microstructure which has been suggested on the basis of detailed electromagnetic measurements on similar samples.

Mechanism of Surface Dissolution in Dense Hydroxyapatite

2007 ◽  
Vol 121-123 ◽  
pp. 1241-1244 ◽  
Author(s):  
Dong Seok Seo ◽  
Hwan Kim ◽  
Jong Kook Lee
Keyword(s):  
Mechanical Properties ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Xrd Analysis ◽  
Boundary Structure ◽  
Molar Ratio ◽  
Dissolution Mechanism ◽  
Grain Boundary Structure ◽  
High Resolution Tem ◽  
Moisture Protection

In this study, it was demonstrated how second phases with small amount, which are hardly detected by XRD analysis, affect grain boundary dissolution and related mechanical properties of HA. All HA disks sintered at 1200 oC for 2 h in air with under moisture protection were phase pure and had Ca/P molar ratio of 1.67. Following certain period of exposure to the distilled water, the surface dissolution initiated at grain boundaries and particle loosening, subsequently resulting in decrease in mechanical properties of HA. In order to understand the dissolution mechanism, grain boundary structure of HA was identified by transmission electron microscopy (TEM) and high resolution TEM observation. From the analysis, it was found that the non-stoichiometric phase as α-tricalcium phosphate (TCP) transformed from β-TCP was existed at grain boundaries and caused surface dissolution of HA. From the XRD analysis, it was found that (211) and (112) planes of hydroxyapatite were susceptible to dissolution, whereas (300) plane was relatively stable.

A Highly Reliable Al Line with Controlled Texture and Grain Boundaries

1995 ◽  
Vol 391 ◽  
Author(s):  
M. Hasunuma ◽  
H. Toyoda ◽  
T. Kawanoue ◽  
S. Ito ◽  
H. Kaneko ◽  
...  
Keyword(s):  
Grain Boundary ◽  
Single Crystal ◽  
Grain Boundaries ◽  
Empirical Relation ◽  
Boundary Structure ◽  
Homogeneous Microstructure ◽  
Grain Boundary Structure ◽  
Dislocation Arrays ◽  
Order Of Magnitude ◽  
Individual Grains

AbstractIn order to clarify the relationship between Al line reliability and film microstructure, especially grain boundary structure and crystal texture, we have tested three kinds of highly textured Al lines, namely, single-crystal Al line, quasi-single-crystal Al line and hypertextured Al line, and two kinds of conventional Al lines deposited on TiN/Ti and on SiO2. Consequently, the empirical relation between the electromigration (EM) lifetime of Al line † and the (111) full width at half maximum (FWHM) value ω is described by † ∝ ω-2 [1]. This improvement of Al line reliability results from as following reasons; firstly, homogeneous microstructure and high activation energy of 1.28eV for the single-crystal Al line (ω=0.18°); secondly, sub-grain boundaries which consisted of dislocation arrays found in the quasi-single-crystal Al line (ω=0.26°) has turned out to be no more effective mass transport paths because dislocation lines are perpendicular to the direction of electron wind. Although there exist plural grain boundary diffusion paths in the newly developed hypertextured Al line (ω=0.5°) formed by using an amorphous Ta-Al underlayer {1], the vacancy flux along the line has been suppressed to the same order of magnitude of single crystal line. It has been clarified that the decrease of FWHM value has promoted the formation of sub-grain boundaries and low-angle boundaries with detailed orientation analysis of individual grains in the hypertextured film. The longer EM lifetime for the hypertextured Al line is considered to be due to the small grain boundary diffusivities for these stable grain boundaries, and this diffusivity reduction resulted in the suppression of void/hillock pair in the Al lines. These results have confirmed that controlling texture and/or grain boundary itself is a promising approach to develop reliable Al lines which withstand higher current densities required in future ULSIs.

Cation Coordination At Σ Grain Boundaries in TiO2 and SrTiO3, and its Effect on the Local Electronic Properties

1999 ◽  
Vol 5 (S2) ◽  
pp. 792-793
Author(s):  
J.A. Zaborac ◽  
J.P. Buban ◽  
H.O. Moltaji ◽  
S. Stemmer ◽  
N.D. Browning
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Electronic Properties ◽  
Defect Formation ◽  
Boundary Structure ◽  
Polycrystalline Materials ◽  
Dominant Effect ◽  
Grain Boundary Structure ◽  
Charge Potential ◽  
Cation Coordination

Grain boundaries have long been known to have a dominant effect on the electronic properties of polycrystalline materials. In the case of electroceramic oxides, the thermodynamics of defect formation (vacancies or interstitials, cations or anions) are usually invoked to predict the presence of a space charge potential at the grain boundaries. The relative energetics for the formation of each type of defect determines the size and sign of this potential barrier and thus, the effect that boundaries have on the overall electronic properties of the materials. However, a limitation to this continuum thermodynamics approach is that it does not consider the effect of the grain boundary structure.To investigate whether the grain boundary atomic structure can have an effect on the energetics of defect formation and hence the electronic properties, here we examine the structure of Σ5 boundaries in two systems, SrTiO3 (perovskite) and TiO2(rutile).

Structure And Composition Of Grain Boundaries In SrTiO3

1999 ◽  
Vol 5 (S2) ◽  
pp. 94-95
Author(s):  
O. Kienzle ◽  
F. Ernst ◽  
Manfred Rühle
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Point Defects ◽  
Coincidence Site Lattice ◽  
Boundary Segregation ◽  
Grain Boundary Segregation ◽  
Boundary Structure ◽  
Dopant Atoms ◽  
Charged Point ◽  
Atomistic Structure

The electrical properties of SrTiO3 (strontium titanate) ceramics are strongly influenced or even dictated by grain boundary segregation of charged point defects, such as dopant atoms, impurities, vacancies, or self-interstitials. The atomistic structure of the grain boundaries, their energy, and the segregation of point defects mutually depend on each other. Grain boundary segregation of charged point defects induces the formation of space charge layers in the adjoining crystals. In order to investigate the relation between grain boundary structure and composition, grain boundaries in Fedoped SrTiO3 bicrystals and in SrTiO3 ceramics were studied by HRTEM and by AEM with subnanometer resolution.Quantitative HRTEM served to investigate the atomistic structure of Σ=3, (111) grain boundaries in Fe-doped SrTiO3 bicrystals with a doping level of Fe/Ti= 0.04at% (Fig. 1). Analysis of the translation state revealed that the Σ=3, (111) grain boundary has an excess volume: normal to the boundary plane, the spacing between the two crystals exceeds what one would expect from a coincidence site lattice model by (0.06 ±0.01 )nm.

Monte Carlo Simulation of Solute-Atom Segregation at Grain Boundaries In Single-Phase Binary Face-Centered Cubic Alloys

1998 ◽  
Vol 4 (S2) ◽  
pp. 764-765
Author(s):  
David N. Seidman ◽  
John D. Rittner ◽  
Dmitry Udler
Keyword(s):  
Grain Boundary ◽  
Grain Boundaries ◽  
Solute Atom ◽  
Boundary Segregation ◽  
Grain Boundary Segregation ◽  
Diffusional Creep ◽  
Boundary Structure ◽  
Temper Brittleness ◽  
Face Centered Cubic ◽  
Boundary Properties

Solute-atom segregation to grain boundaries has been of interest since the 1930's when it was realized that some steels were susceptible to failure by intergranular fracture when certain impurities were present. Segregation of impurities or intentionally added alloying elements at grain boundaries can greatly affect various grain boundary properties, which in turn affect numerous macroscopic properties. Materials phenomena that have been linked to grain boundary segregation include temper brittleness, fatigue strength, adhesion, precipitation, diffusional creep, intergranular corrosion, and grain boundary diffusivity. Although grain boundary segregation has been extensively studied for many years, the effects of different grain boundary structures on segregation was generally not considered. It has been established both experimentally and theoretically that the level of segregation varies from grain boundary to grain boundary in the same alloy, but there is little direct information on how grain boundary structure influences segregation.

Sign in / Sign up

Export Citation Format

Share Document