Microstructure of Nanocrystalline Ceramics

1988 ◽  
Vol 132 ◽  
Author(s):  
H. Hahn ◽  
J. Logas ◽  
H. J. Höfler ◽  
Th. Bier ◽  
R. S. Averback
Keyword(s):  
Grain Growth ◽  
Sintering Temperature ◽  
Total Pore Volume ◽  
Nitrogen Adsorption ◽  
Green Body ◽  
X Ray Diffraction ◽  
Adsorption Method ◽  
X Ray ◽  
Nanocrystalline Ceramics ◽  
Scanning Electron

ABSTRACTThe microstructure of nanocrystalline (n-) TiO2 was studied as a function of sintering temperature up to 1273 K. Grain growth was monitored using x-ray diffraction and scanning electron microscopy. Measurements of density and permeability of He and Ar were also conducted. The specific surface area and the total pore volume were determined quantitatively using the nitrogen adsorption method. These measurements revealed that highly compacted n-TiO2 had green body densities as high as 75 % of bulk density and that sintering occurred at much lower temperatures than in conventional powder. Densification proceeded by loss of the small pores first. The possibilities of achieving high densities with limited grain growth will be discussed.

Chemically Treated Submicron Illite Clays for Product with Improved Strength

2015 ◽  
Vol 1117 ◽  
pp. 152-155
Author(s):  
Liga Grase ◽  
Gundars Mezinskis ◽  
Inta Vitina
Keyword(s):  
Electron Microscopy ◽  
Raw Materials ◽  
Nitrogen Adsorption ◽  
Raw Material ◽  
Industrial Minerals ◽  
X Ray Diffraction ◽  
Adsorption Method ◽  
X Ray ◽  
Different Temperatures ◽  
Scanning Electron

A variety of industrial minerals, such as kaolinite, feldspars, and etc., have been used as solid raw materials in the geopolymerization technology. The illite-containing raw material in this study was obtained by the use of sedimentation method. Clay and dust fractions was subjected to the treatment with NaOH alkaline solution and afterwards treated at different temperatures. Results obtained by X-ray diffraction, Scanning electron microscopy, nitrogen adsorption method confirmed the usability of Liepas deposit homogenized gray and red clays for possible realization of geopolymer method.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Preparation and Characterisation of TiO2 Thick Films Fabricated by Electrophoretic Deposition

2007 ◽  
Vol 561-565 ◽  
pp. 2163-2166 ◽  
Author(s):  
H.Z. Abdullah ◽  
Charles C. Sorrell
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Growth ◽  
Electrophoretic Deposition ◽  
Defect Formation ◽  
Titanium Foil ◽  
X Ray Diffraction ◽  
Voltage Range ◽  
X Ray ◽  
Scanning Electron

Rutile nano-powders were suspended in a solution of acetylacetone and iodine. The suspensions were electrophoretically deposited on titanium foil at a voltage range of 5-30 V over times of 5-120 s. The dried tapes then were sintered at 800°C for 2 h in flowing argon. Both the green and fired tapes were examined by field emission scanning electron microscopy, optical microscopy, X-ray diffraction, and Raman microspectroscopy. The thickness of the films depended on the voltage and the time of deposition. The sintered microstructures depended significantly on the thickness of the film, which was a function the proximity to the Ti/TiO2 interface. The interface is critical to the microstructure because it acts as the source of defect formation, which enhances sintering, grain growth, and grain facetting.

scholarly journals Pengaruh Suhu Sintering Terhadap Sintesis Silicon Carbide (SiC) Berbahan Dasar Abu Sekam Padi dan Grafit Pensil 2B

2015 ◽  
Vol 5 (01) ◽  
pp. 31
Author(s):  
Resky Irfanita ◽  
Asnaeni Ansar ◽  
Ayu Hardianti Pratiwi ◽  
Jasruddin J ◽  
Subaer S
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Silicon Carbide ◽  
Rice Husk Ash ◽  
Sintering Temperature ◽  
Solid State Reaction Method ◽  
X Ray Diffraction ◽  
Reaction Method ◽  
X Ray ◽  
Scanning Electron

The objective of this study is to investigate the effect of sintering temperature on the synthesis of SiC produced from rice husk ash (RHA) and 2B graphite pencils. The SiC was synthesized by using solid state reaction method sintered at temperatures of 750°C, 1000°C and 1200°C for 26 hours, 11.5 hours and 11.5 hours, respectively. The quantity and crystallinity level of SiC phase were measured by means of Rigaku MiniFlexII X-Ray Diffraction (XRD). The microstructure of SiC was examined by using Tescan Vega3SB Scanning Electron Microscopy (SEM). The XRD results showed that the concentration (wt%) of SiC phase increases with the increasing of sintering temperature. SEM results showed that the crystallinity level of SiC crystal is improving as the sintering temperature increases

Preparation and Microstructure of Pressureless Sintered Si2ON2-SiC Ceramic

2011 ◽  
Vol 335-336 ◽  
pp. 699-703
Author(s):  
Hui Hui Tan ◽  
Zhu Xing Tang ◽  
Xia Zhao ◽  
He Zhang
Keyword(s):  
Bulk Density ◽  
Sintering Temperature ◽  
Pressureless Sintering ◽  
Nitriding Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Effect Of Additives ◽  
Sic Ceramic ◽  
Sintering Method ◽  
Scanning Electron

This paper introduces Si2ON2-SiC ceramic fabricated by pressureless sintering method and studies the effect of additives, nitriding temperatures on bulk density, porosity, phase composition and microstructure. It is discovered that additives MgO, CeO2 can increase the densities of Si2ON2-SiC ceramic apparently, and MgO additive has a better effect than CeO2. Nitriding temperature also is an important factor. The bulk density of the specimen with MgO additive reaches maximum at 1.91 g/cm3 when sintered at 1450 °C, and the bulk density of specimen with CeO2 additive is 1.86 g/cm3 at the same condition while the bulk density of the specimen without additive is only 1.75 g/cSuperscript textm3. The X-ray diffraction and scanning electron microscopy of the specimens show that the amount of Si2ON2 increase with the sintering temperature increase. But when the temperature is higher than 1500 °C the Si2ON2 grains will decompose into Si3N4, and Si2ON2 will vanish at 1550 °C

Study on the Properties of Doped La in BaBi4Ti4O15 Ceramic

2007 ◽  
Vol 26-28 ◽  
pp. 243-246
Author(s):  
Xing Hua Yang ◽  
Jin Liang Huang ◽  
Xiao Wang ◽  
Chun Wei Cui
Keyword(s):  
Crystal Structure ◽  
Grain Size ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sintering Temperature ◽  
Solid Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lanthanum Content ◽  
Scanning Electron

BaBi4-xLaxTi4O15 (BBLT) ceramics were prepared by conventional solid phase sintering ceramics processing technology. The crystal structure and the microstructure were detected by X-ray diffraction (XRD) and scanning electron microscope (SEM). The XRD analyses show that La3+ ions doping did not change the crystal structure of BBT ceramics. The sintering temperature increased from 1120°C to 1150°C with increasing Lanthanum content from 0 to 0.5, but it widened the sintering temperature range from 20°C to 50°C and refined the grain size of the BBT ceramic. Additionally, polarization treatment was performed and finally piezoelectric property was measured. As a result, the piezoelectric constant d33 of the 0.1at.% doped BBLT ceramics reached its highest value about 22pc/N at polarizing electric field of 8kV/mm and polarizing temperature of 120°C for 30min.

Preparation of the System of BaO-MgO-Al2O3-TiO2 Acid-Resistant Fracturing Proppants

2011 ◽  
Vol 399-401 ◽  
pp. 855-859
Author(s):  
Ting Ting Wu ◽  
Bo Lin Wu
Keyword(s):  
Sintering Temperature ◽  
Raw Materials ◽  
Acid Resistance ◽  
Pressureless Sintering ◽  
Alumina Matrix ◽  
X Ray Diffraction ◽  
X Ray ◽  
Acid Solubility ◽  
Resistance Performance ◽  
Scanning Electron

In order to improve the acid resistance and reduce the apparent density of fracturing proppants, TiO2 powder added in the system of BaO-MgO-Al2O3 fracturing proppants were prepared by the technique of pressureless sintering. The properties of the samples were investigated by the measurements of acid solubility, X-ray diffraction and scanning electron microscopy. The results show that the acid solubility of alumina matrix fracturing proppants contenting TiO2 of the 4wt% and BaO/MgO with the ratio of 3:7 is 0.15%. It is an important development in acid resistance performance of fracturing proppants research on laboratory. TiO2 is added to the raw materials and then calcine them to ceramics, which can reduces the sintering temperature, promote the densification and improve acid-resistant property of fracturing proppants.

Spark Plasma Sintering of Paper-Derived Ti3AlC2-Based Composites: Influence of Sintering Temperature

2021 ◽  
Vol 1016 ◽  
pp. 1790-1796
Author(s):  
Maxim Syrtanov ◽  
Egor Kashkarov ◽  
Tatyana Murashkina ◽  
Nahum Travitzky
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Total Content ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carbide Phases ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Scanning Electron

This paper describes the influence of sintering temperature on phase composition and microstructure of paper-derived Ti3AlC2 composites fabricated by spark plasma sintering. The composites were sintered at 100 MPa pressure in the temperature range of 1150-1350 °C. Phase composition and microstructure were analyzed by X-ray diffraction and scanning electron microscopy, respectively. The multiphase structure was observed in the sintered composites consisting of Ti3AlC2, Ti2AlC, TiC and Al2O3 phases. The decomposition of the Ti3AlC2 phase into Ti2AlC and TiC carbide phases was observed with temperature rise. The total content of Ti3AlC2 and Ti2AlC phases was reduced from 84.5 vol.% (1150 °C) to 69.5 vol.% (1350 °C). The density of composites affected by both the content of TiC phase and changes in porosity.

Effect of Sintering Temperature on Microstructure and Electrical Properties of Nanozinc Oxide Varistor

2011 ◽  
Vol 495 ◽  
pp. 190-193 ◽  
Author(s):  
Mehdi Mirzayi ◽  
Mohammad Hoseen Hekmatshoar ◽  
Abdolazim Azimi
Keyword(s):  
Electrical Properties ◽  
Sintering Temperature ◽  
Voltage Characteristic ◽  
X Ray Diffraction ◽  
Current Voltage Characteristic ◽  
X Ray ◽  
Current Voltage ◽  
Polyacrylamide Gel Method ◽  
Zno Powder ◽  
Scanning Electron

Nanometer-sized ZnO powder was synthesized at low decomposing temperature by polyacrylamide-gel method where Acrylamide was used as monomer, and N,N-methylene-bisacrylamide as lattice reagent. The characteristic of powders were studied by X-ray diffraction and scanning electron microscope (SEM). The results indicated uniform distribution of nanoZnO particles. Also electrical properties were investigated at different sintering temperatures of 800, 900 and 1000 ° C. It was observed that increase in sintering temperature, resulted in increase in the grain size of the varistor ceramics. The observed nonlinearity in current – voltage characteristic was explained by the existence of potential barrier at the grain boundaries and lowering of the barriers.

Sintering AlN Ceramics Below 1500°C with MgO-CaO-Al2O3-SiO2 Glass Addition

2007 ◽  
Vol 336-338 ◽  
pp. 1868-1871 ◽  
Author(s):  
Cheng Fu Yang ◽  
Chien Min Cheng ◽  
Ho Hua Chung ◽  
Chao Chin Chan
Keyword(s):  
Sintering Temperature ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Dielectric Characteristics ◽  
Sintering Aid ◽  
Glass Addition ◽  
X Ray ◽  
Crystal Phases ◽  
Diffraction Patterns ◽  
Scanning Electron

5~15 wt% MgO-CaO-Al2O3-SiO2 (MCAS, fabricated by sol-gel method) glass is used as the sintering aid of AlN ceramics. The sintering is proceeded from 1350oC~1550oC, scanning electron microscope is used to observe the sintered morphologies and X-ray diffraction pattern are used to confirm the crystal structures. From the SEM observations, as 10wt% and 15wt% MCAS is added, AlN ceramics can be densified at 1500oC and 1450oC, which are much lower than the before studies were. From the X-ray diffraction patterns, the crystal phases of MCAS-AlN ceramics are AlN, Al2O3, and cordierite phases. In this study, the dielectric characteristics of MCAS-AlN ceramics are also developed as a function of MCAS content and sintering temperature.

Sign in / Sign up

Export Citation Format

Share Document