Synthesis of Buried Silicon Compounds Using Ion Implantation

1988 ◽  
Vol 100 ◽  
Author(s):  
Alice E. White ◽  
K. T. Short ◽  
R. C. Dynes ◽  
J. M. Gibson ◽  
R. Hull

ABSTRACTIon implantation is widely used for doping semiconductors at low concentration, but, with the advent of a new generation of high current implanters, synthesizing new materials rather that simply doping them has become feasible. This technique has been successfully applied to fabricating silicon-on-insulator (SOI) structures with oxygen and nitrogen for several years. Since we are interested in understanding the mechanisms of formation of these layers, we have concentrated on sub-stoichiometric implantation doses of oxygen where it is easier to observe the coalescing layer. In order to determine whether this process of compound formation is more general, our studies were expanded to include implantation of the transition metals. Here, elevated substrate temperatures are necessary to minimize Si surface damage. The resulting disilicide layers are of remarkably high quality: they are single crystals in registry with the silicon wafer and they have better residual resistivities than comparable UHV-reacted silicides.

1987 ◽  
Vol 107 ◽  
Author(s):  
Alice E. White ◽  
K. T. Short ◽  
R. C. Dynes ◽  
J. M. Gibson ◽  
R. Hull

AbstractIon implantation is widely used for doping semiconductors at low concentration, but, with the advent of a new generation of high current implanters, synthesizing new materials rather that simply doping them has become feasible. This technique has been successfully applied to fabricating silicon-on-insulator (SOI) structures with oxygen and nitrogen for several years. Since we are interested in understanding the mechanisms of formation of these layers, we have concentrated on sub-stoichiometric implantation doses of oxygen where it is easier to observe the coalescing layer. In order to determine whether this process of compound formation is more general, our studies were expanded to include implantation of the transition metals. Here, elevated substrate temperatures are necessary to minimize Si surface damage. The resulting disilicide layers are of remarkably high quality: they are single crystals in registry with the silicon wafer and they have better residual resistivities than comparable UHV-reacted suicides.


MRS Bulletin ◽  
1992 ◽  
Vol 17 (6) ◽  
pp. 40-46 ◽  
Author(s):  
G.K. Celler ◽  
Alice E. White

Experiments in ion implantation were first performed almost 40 years ago by nuclear physicists. More recently, ion implanters have become permanent fixtures in integrated circuit processing lines. Manufacture of the more complex integrated circuits may involve as many as 10 different ion implantation steps. Implantation is used primarily at f luences of 1012–1015 ions/cm2 to tailor the electrical properties of a semiconductor substrate, but causing only a small perturbation in the composition of the target (see the article by Seidel and Larson in this issue of the MRS Bulletin). Applications of implantation had been limited by the small beam currents that were available, but recently a new generation of high-current implanters has been developed. This high-current capability allows implanting concentrations up to three orders of magnitude higher than those required for doping—enough to create a compound.


Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.


Author(s):  
P. Roitman ◽  
B. Cordts ◽  
S. Visitserngtrakul ◽  
S.J. Krause

Synthesis of a thin, buried dielectric layer to form a silicon-on-insulator (SOI) material by high dose oxygen implantation (SIMOX – Separation by IMplanted Oxygen) is becoming an important technology due to the advent of high current (200 mA) oxygen implanters. Recently, reductions in defect densities from 109 cm−2 down to 107 cm−2 or less have been reported. They were achieved with a final high temperature annealing step (1300°C – 1400°C) in conjunction with: a) high temperature implantation or; b) channeling implantation or; c) multiple cycle implantation. However, the processes and conditions for reduction and elimination of precipitates and defects during high temperature annealing are not well understood. In this work we have studied the effect of annealing temperature on defect and precipitate reduction for SIMOX samples which were processed first with high temperature, high current implantation followed by high temperature annealing.


Author(s):  
A. De Veirman ◽  
J. Van Landuyt ◽  
K.J. Reeson ◽  
R. Gwilliam ◽  
C. Jeynes ◽  
...  

In analogy to the formation of SIMOX (Separation by IMplanted OXygen) material which is presently the most promising silicon-on-insulator technology, high-dose ion implantation of cobalt in silicon is used to synthesise buried CoSi2 layers. So far, for high-dose ion implantation of Co in Si, only formation of CoSi2 is reported. In this paper it will be shown that CoSi inclusions occur when the stoichiometric Co concentration is exceeded at the peak of the Co distribution. 350 keV Co+ ions are implanted into (001) Si wafers to doses of 2, 4 and 7×l017 per cm2. During the implantation the wafer is kept at ≈ 550°C, using beam heating. The subsequent annealing treatment was performed in a conventional nitrogen flow furnace at 1000°C for 5 to 30 minutes (FA) or in a dual graphite strip annealer where isochronal 5s anneals at temperatures between 800°C and 1200°C (RTA) were performed. The implanted samples have been studied by means of Rutherford Backscattering Spectroscopy (RBS) and cross-section Transmission Electron Microscopy (XTEM).


2021 ◽  
Vol 11 (10) ◽  
pp. 4372
Author(s):  
Sergey G. Anikeev ◽  
Anastasiia V. Shabalina ◽  
Sergei A. Kulinich ◽  
Nadezhda V. Artyukhova ◽  
Daria R. Korsakova ◽  
...  

A new approach to fabricate TiNi surfaces combining the advantages of both monolithic and porous materials for implants is used in this work. New materials were obtained by depositing a porous TiNi powder onto monolithic TiNi plates followed by sintering at 1200 °C. Then, further modification of the material surface with a high-current-pulsed electron beam (HCPEB) was carried out. Three materials obtained (one after sintering and two after subsequent beam treatment by 30 pulses with different pulse energy) were studied by XRD, SEM, EDX, surface profilometry, and by means of electrochemical measurements, including OCP and EIS. Structural and compositional changes caused by HCPEB treatment were investigated. Surface properties of the samples during their storage in saline for 10 days were studied and a model experiment with cell growth (MCF-7) was carried out for the unmodified sample with an electron beam to detect cell appearance on different surface locations.


2012 ◽  
Vol 90 (1) ◽  
pp. 39-43 ◽  
Author(s):  
X. Xiang ◽  
D. Chang ◽  
Y. Jiang ◽  
C.M. Liu ◽  
X.T. Zu

Anatase TiO2 thin films are deposited on K9 glass samples at different substrate temperatures by radio frequency magnetron sputtering. N ion implantation is performed in the as-deposited TiO2 thin films at ion fluences of 5 × 1016, 1 × 1017, and 5 × 1017 ions/cm2. X-ray diffraction, atomic force microscope, X-ray photoelectron spectroscopy (XPS), and UV–visible spectrophotometer are used to characterize the films. With increasing N ion fluences, the absorption edges of anatase TiO2 films shift to longer wavelengths and the absorbance increases in the visible light region. XPS results show that the red shift of TiO2 films is due to the formation of N–Ti–O compounds. As a result, photoactivity is enhanced with increasing N ion fluence.


Author(s):  
I.G. Brown ◽  
M.R. Dickinson ◽  
J.E. Galvin ◽  
X. Godechot ◽  
R.A. MacGill

Sign in / Sign up

Export Citation Format

Share Document