Effect of Ti Microaddition on Cavitation Behavior During Uniaxial Hot-Tensile of Fe-22Mn-1.5Al-1.3Si-0.5C Austenitic TWIP Steel

2016 ◽  
Vol 1812 ◽  
pp. 123-128 ◽  
Author(s):  
Antonio E. Salas-Reyes ◽  
Ignacio Mejía ◽  
José M. Cabrera
Keyword(s):  
Grain Boundary ◽  
Crack Growth ◽  
Fracture Behavior ◽  
Twip Steel ◽  
Research Work ◽  
Grain Boundary Sliding ◽  
Crack Growth Behavior ◽  
Premature Failure ◽  
Damage And Fracture ◽  
Twip Steels

ABSTRACTIt is well-known that metal and alloys develop internal cavities when subjected to uniaxial or multiaxial tensile strains at elevated temperature. In most cases, cavitation may lead to premature failure during forming. Therefore, damage and fracture behavior imposes significant limitations in hot metal-forming processes. Although high-Mn austenitic TWIP steels exhibit a unique combination of strength and ductility, cavitation during hot working is one issue that must be tackled. The aim of this research work is to determine the effect of Ti microaddition on cavity mechanisms of Fe-22Mn-1.5Al-1.3Si-0.5C TWIP steel under uniaxial hot-tensile condition at 800 °C and constant true strain rate of 10-3 s-1. For this purpose, light optical (LOM) and scanning electron (SEM) microscopies and image analysis were applied to quantify cavities formation along longitudinal section of deformed samples near to the fracture surface. The number of cavities greater than 10 µm (critical length) in non-microalloyed and Ti microalloyed TWIP steels were 2.75 and 3.75 cavities/mm2, respectively. On the other hand, average cavity area was 125 and 152 µm2, respectively. Both TWIP steels showed cavities type “r”, “l” and “A”. Finally, Ti microaddition to TWIP steel resulted in a predominant brittle fracture behavior due to finer grain-boundary precipitation, which weakens grains cohesion and accelerates crack growth by grain-boundary sliding. In this case, crack growth behavior is explained in terms of a void interconnection mechanism.

Examination of Fracture Interfaces in Silicon Nitride

1975 ◽  
Vol 33 ◽  
pp. 60-61
Author(s):  
Nancy J. Tighe
Keyword(s):  
Silicon Nitride ◽  
Grain Boundary ◽  
Crack Growth ◽  
Subcritical Crack Growth ◽  
Slow Crack Growth ◽  
Ceramic Materials ◽  
Grain Boundary Sliding ◽  
Boundary Phase ◽  
Turbine Engines ◽  
Boundary Sliding

Silicon nitride is one of the ceramic materials being considered for the components in gas turbine engines which will be exposed to temperatures of 1000 to 1400°C. Test specimens from hot-pressed billets exhibit flexural strengths of approximately 50 MN/m2 at 1000°C. However, the strength degrades rapidly to less than 20 MN/m2 at 1400°C. The strength degradition is attributed to subcritical crack growth phenomena evidenced by a stress rate dependence of the flexural strength and the stress intensity factor. This phenomena is termed slow crack growth and is associated with the onset of plastic deformation at the crack tip. Lange attributed the subcritical crack growth tb a glassy silicate grain boundary phase which decreased in viscosity with increased temperature and permitted a form of grain boundary sliding to occur.

Fracture Behavior of Ceramics Used in Multilayer Capacitors

1986 ◽  
Vol 72 ◽  
Author(s):  
Theresa L. Baker ◽  
Stephen W. Freiman
Keyword(s):  
Crack Growth ◽  
Fracture Behavior ◽  
Ceramic Materials ◽  
Fatigue Tests ◽  
Internal Stresses ◽  
Crack Growth Behavior ◽  
Multilayer Capacitors ◽  
Materials Used ◽  
Aging Phenomena

AbstractThis study involved the determination of the effects of composition and microstructure on the fracture toughness and susceptibility to environmentally enhanced crack growth of several ceramic materials used in multilayer capacitors. Indentation-fracture procedures were used to measure KIC as well as to assess the possible effects of internal stresses on the fracture behavior of these materials and to correlate dielectric aging phenomena with strength. The environmentally enhanced crack growth behavior of these materials was determined by conducting dynamic fatigue tests in water.

Heat Input Effect on the Microstructure of Twinning-Induced Plasticity (TWIP) Steel Welded Joints Through the GTAW Process

MRS Advances ◽  
2018 ◽  
Vol 3 (64) ◽  
pp. 3949-3956
Author(s):  
H. Hernández-Belmontes ◽  
I. Mejía ◽  
V. García-García ◽  
C. Maldonado
Keyword(s):  
Phase Transformations ◽  
Heat Input ◽  
Twip Steel ◽  
Research Work ◽  
Second Phase ◽  
Current Electrode ◽  
Weld Joints ◽  
Average Grain Size ◽  
Gtaw Process ◽  
Twip Steels

ABSTRACTHigh-Mn Twinning Induced Plasticity (TWIP) steels are an excellent alternative in the design of structural components for the automotive industry. The TWIP steels application allows weight reduction, maintaining the performance of vehicles. Nowadays the research works focused on TWIP steel weldability are relative scarce. It is well-known that weldability is one of the main limitations for industrial application of TWIP steel. The main goal of this research work was studied the effect of heat input on the microstructural changes generated in a TWIP steel microalloyed with Ti. A pair of welds were performed through Gas Tungsten Arc Welding (GTAW) process. The GTAW process was carried out without filler material, using Direc Current Electrode Negative (DCEN), tungsten electrode EWTh-2 and Ar as shielding gas. The microstructure and average grain size in the fusion (FZ) and heat affected zone (HAZ) were determined by light optical metallography (LOM). Elements segregation in the FZ was evaluated using point and elemental mapping chemical analysis (EPMA) by Scanning Electron Microscopy and Electron Dispersive Spectroscopy (SEM-EDS). Phase transformations were evaluated using X-ray diffraction (XRD). Finally, the hardness were measured by means of Vickers microhardness testing (HV500). The results show that the FZ is characterized by a dendritic solidification pattern. Meanwhile, the HAZ presented equiaxed grains in both weld joints. On the other hand, the TWIP-Ti steel weldments did not present austenite phase transformations. Nevertheless, the FZ exhibited variations in the chemical elements distribution (Mn, Al, Si and C), which were higher as the heat input increases. Finally, the heat input reduced the microhardness of TWIP-Ti steel weld joints. Although post-welding hardness recovery was detected, which is associated with precipitation of Ti second-phase particles.

Coupled effect of grain boundary sliding and dislocation emission on fracture toughness of nanocrystalline materials

2016 ◽  
Vol 01 (02) ◽  
pp. 1650008 ◽  
Author(s):  
Q. H. Fang ◽  
L. C. Zhang
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Crack Growth ◽  
Nanocrystalline Materials ◽  
Crack Tip ◽  
Grain Boundary Sliding ◽  
Dislocation Emission ◽  
Disclination Dipole ◽  
Coupled Effect ◽  
Wedge Disclination

This paper establishes a theoretical model to explore the coupled effect of grain boundary (GB) sliding deformation and crack tip dislocation emission on the critical stress intensity factor (SIF) for crack growth in ultrafine-grained and nanocrystalline materials (NCMs). The model postulates that the stress concentration near a crack tip initiates GB sliding. It is found that GB sliding leads to the formation of wedge disclination dipole at the triple junctions of grain boundaries. Under the external load and stress fields produced by wedge disclinations, dislocations are emitted from crack tips but will stop at the opposite GBs. The influence of the wedge disclination dipole and the dislocation emitted from crack tip on the critical SIF for crack growth is investigated. The model prediction shows that the critical SIF varies with the decrement of grain size, and that there is a critical grain size corresponding to a minimum value of SIF. Compared with the pure brittle fracture in NCMs at the grain sizes of tens of nanometers, the combined deformation mechanisms can bring an increase of the critical SIF for crack growth.

Stress Corrosion Cracking Analysis under Thermal Residual Stress Field Using S-FEM

2011 ◽  
Vol 462-463 ◽  
pp. 431-436 ◽  
Author(s):  
Masanori Kikuchi ◽  
Yoshitaka Wada ◽  
Yuto Shimizu ◽  
Yu Long Li
Keyword(s):  
Residual Stress ◽  
Stress Field ◽  
Crack Growth ◽  
Fracture Behavior ◽  
Three Dimensional ◽  
Stress Fields ◽  
Crack Growth Behavior ◽  
Residual Stress Field ◽  
Energy Agency ◽  
Thermal Stress Field

Fracture in heat affected zone (HAZ) in welding has been a serious problem for the integrity of machines. Prediction of fracture behavior due to the residual stress field in HAZ is important. In this paper, S-Version FEM(S-FEM) is applied to simulate the crack growth under thermal and residual stress fields. For evaluation of stress intensity factor, virtual crack closure integral method (VCCM) is employed. In order to confirm the validity of this analysis, numerical results are compared with previously-reported analytical and experimental results. Then, crack growth analysis in piping structure with welding joint was conducted. The residual stress data was provided by JAEA, Japan Atomic Energy Agency, based on their numerical simulation. Using S-FEM, two- and three-dimensional analyses are conducted, and crack growth behavior under thermal stress field is studied and discussed.

Sign in / Sign up

Export Citation Format

Share Document