Ab Initio Study of Weldability of a High-Manganese Austenitic Twinning-Induced Plasticity (TWIP) Steel Microalloyed with Boron

2016 ◽  
Vol 1812 ◽  
pp. 35-40 ◽  
Author(s):  
Humberto Hernández-Belmontes ◽  
Ignacio Mejía ◽  
Cuauhtémoc Maldonado
Keyword(s):  
Fusion Zone ◽  
Twip Steel ◽  
Mechanical Performance ◽  
Research Work ◽  
Base Material ◽  
High Strength Steels ◽  
High Strength ◽  
Strengthening Mechanism ◽  
Microstructural Changes ◽  
Twip Steels

ABSTRACTHigh-Mn Twinning-Induced Plasticity (TWIP) steels are advanced high-strength steels (AHSS) currently under development; they are fully austenitic and characterized by twinning as the predominant strengthening mechanism. TWIP steels have high strength and formability with an elongation up to 80%, which allows reduction in automotive components weight and fuel consumption. Since the targeted application field of TWIP steels is the automotive industry, steels need high mechanical performance with good weldability and excellent corrosion resistance. However, there is lack of information about the weldability behavior of these advanced steels. This research work aims to study the weldability of a new generation of high-Mn austenitic TWIP steels microalloyed with B. Weldability was examined using spot welds produced by Gas Tungsten Arc Welding. Microstructural changes were examined using light optical metallography. Segregation of elements in the weld joint was evaluated using point and elemental mapping chemical analysis by Scanning Electron Microscopy and Electron-Dispersive Spectroscopy; while the hardness properties were examined with Vickers microhardness testing (HV25). Experimental results show that the welded joint microstructure consists of austenitic dendritic grains in the fusion zone, and equiaxed grains in the heat affected zone. Notably, the boron microalloyed TWIP steel exhibited poor weldability, showing hot cracking. Additionally, the studied TWIP steels showed a high degree of segregation in the fusion zone; Mn and Si segregated into the interdendritic regions, while Al and C preferentially segregated in dendritic areas. Finally, the welded joints of the TWIP steels showed microhardness values lower than the base material. In general, the present TWIP steels have problems of weldability, which are corroborated with microstructural changes, elements segregation and microhardness loss.

Wear Resistance under Non-Lubricated Condition of Nb-Containing TWIP Steel

MRS Advances ◽  
2017 ◽  
Vol 2 (61) ◽  
pp. 3765-3771
Author(s):  
V.H. Mercado ◽  
I. Mejía ◽  
Y. Salinas-Escutia ◽  
A. Bedolla-Jacuinde
Keyword(s):  
Wear Resistance ◽  
Twip Steel ◽  
Wear Behavior ◽  
Research Work ◽  
High Strength Steels ◽  
Mechanical Twinning ◽  
High Manganese ◽  
Structural Applications ◽  
Twip Steels ◽  
Nb Addition

ABSTRACTTwinning induced plasticity (TWIP) steels are one of the most attractive advanced high-strength steels for structural applications due to their unique combination of strength and ductility, which is associated with so-called “mechanical twinning”, where twins act as strong obstacles to the dislocation motion. In this context, Nb addition to TWIP steel increases the strength and refines grain size by nanoscale NbC precipitates. Nowadays, high-manganese TWIP steels are extensively studied. However, information in the specialized literature about their tribological properties is limited. This research work studies the wear behavior of high-manganese austenitic Fe–20Mn–1.5Si–1.5Al–0.4C TWIP steel microalloyed with Nb. The wear behavior was evaluated under non-lubricated sliding condition using the “pin-on-ring” technique. As-solution heat treated samples were worn under loads of 53, 104 and 154 N, and at sliding speeds of 0.22, 0.60 and 0.87 m/s. The wear resistance was evaluated in terms of the loss weight. Wear debris and worn surfaces were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD). In general, results show that the wear resistance significantly improves as the sliding speed increases. On the other hand, Nb addition to present TWIP steel produces a slight increase of the wear resistance. Also, it was found that the oxide layer plays a significant role in the wear resistance behavior of this kind of steel.

Welding Properties and Fatigue Resistance of S690QL High Strength Steels

2015 ◽  
Vol 812 ◽  
pp. 29-34 ◽  
Author(s):  
Ádám Dobosy ◽  
János Lukács
Keyword(s):  
Fatigue Resistance ◽  
Welded Joints ◽  
Gas Metal Arc Welding ◽  
Research Work ◽  
Base Material ◽  
High Strength Steels ◽  
High Strength ◽  
Fatigue Tests ◽  
Metal Arc Welding ◽  
Welding Properties

The objective of this article is to present the first results of our research work. In order to determination and comparison of the fatigue resistance, high cycle fatigue tests (HCF) were performed on RUUKKI OPTIM S690QL quenched and tempered high strength steel. In parallel these; welded joints were made on the same steel using gas metal arc welding (GMAW, MIG/MAG) to preparation of the cyclic investigations of the welded joints. In the article, the performance of the welding experiments will be presented; along with the results of the HCF tests executed on the base material and its welded joints. Furthermore, our results will be compared with different literary data.

scholarly journals Influence of Nb Microaddition on Microstructure and Texture Evolution in a Fe-21Mn-1.3Al-1.5Si-0.5C TWIP Steel under Uniaxial Hot-Tensile Conditions

MRS Advances ◽  
2017 ◽  
Vol 2 (61) ◽  
pp. 3797-3803
Author(s):  
A.E. Salas-Reyes ◽  
I. Mejía ◽  
J.M. Cabrera
Keyword(s):  
Crystallographic Orientation ◽  
Twip Steel ◽  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
Constant Strain Rate ◽  
High Strength Steels ◽  
High Strength ◽  
Orientation Distribution ◽  
Deformation State ◽  
Twip Steels

ABSTRACTAdvanced high-strength steels as Twinning Induced Plasticity (TWIP) steels have been developed using microalloying elements and subsequent thermo-mechanical processing techniques. Moreover, under hot-working conditions, these steels undergo significant microstructural changes as a result of preferred crystallographic orientation (texture) of grains. In order to evaluate this behavior, one non-microalloyed and other single Nb-microalloyed TWIP steels were melted in an induction furnace and cast into metal and sand molds. Samples with austenitic grain sizes between 400 and 2000 µm were deformed at 800 °C and strained at a constant strain rate of 10-3 s-1, and deformation state was examined by means of electron backscatter diffraction (EBSD) technique near to the fracture tip. It was found that non-microalloyed TWIP steel solidified in both metal and sand mold exhibits dynamically recrystallized grains. On the other hand, Nb microaddition has a strong influence in TWIP steel retarding the onset of recrystallization kinetics, showing low angle sub-structured grains. Furthermore, it was possible identifying the crystallographic orientation of grains using the inverse pole figures (IPF) and the orientation distribution function (ODF). Weak cube {001}<100> recrystallization and E{111}<110> γ-fiber deformation textures components were detected.

Heat Input Effect on the Microstructure of Twinning-Induced Plasticity (TWIP) Steel Welded Joints Through the GTAW Process

MRS Advances ◽  
2018 ◽  
Vol 3 (64) ◽  
pp. 3949-3956
Author(s):  
H. Hernández-Belmontes ◽  
I. Mejía ◽  
V. García-García ◽  
C. Maldonado
Keyword(s):  
Phase Transformations ◽  
Heat Input ◽  
Twip Steel ◽  
Research Work ◽  
Second Phase ◽  
Current Electrode ◽  
Weld Joints ◽  
Average Grain Size ◽  
Gtaw Process ◽  
Twip Steels

ABSTRACTHigh-Mn Twinning Induced Plasticity (TWIP) steels are an excellent alternative in the design of structural components for the automotive industry. The TWIP steels application allows weight reduction, maintaining the performance of vehicles. Nowadays the research works focused on TWIP steel weldability are relative scarce. It is well-known that weldability is one of the main limitations for industrial application of TWIP steel. The main goal of this research work was studied the effect of heat input on the microstructural changes generated in a TWIP steel microalloyed with Ti. A pair of welds were performed through Gas Tungsten Arc Welding (GTAW) process. The GTAW process was carried out without filler material, using Direc Current Electrode Negative (DCEN), tungsten electrode EWTh-2 and Ar as shielding gas. The microstructure and average grain size in the fusion (FZ) and heat affected zone (HAZ) were determined by light optical metallography (LOM). Elements segregation in the FZ was evaluated using point and elemental mapping chemical analysis (EPMA) by Scanning Electron Microscopy and Electron Dispersive Spectroscopy (SEM-EDS). Phase transformations were evaluated using X-ray diffraction (XRD). Finally, the hardness were measured by means of Vickers microhardness testing (HV500). The results show that the FZ is characterized by a dendritic solidification pattern. Meanwhile, the HAZ presented equiaxed grains in both weld joints. On the other hand, the TWIP-Ti steel weldments did not present austenite phase transformations. Nevertheless, the FZ exhibited variations in the chemical elements distribution (Mn, Al, Si and C), which were higher as the heat input increases. Finally, the heat input reduced the microhardness of TWIP-Ti steel weld joints. Although post-welding hardness recovery was detected, which is associated with precipitation of Ti second-phase particles.

Effect of boron on the continuous cooling transformation kinetics in a low carbon advanced ultra-high strength steel (A-UHSS)

2012 ◽  
Vol 1485 ◽  
pp. 83-88 ◽  
Author(s):  
G. Altamirano ◽  
I. Mejía ◽  
A. Hernández-Expósito ◽  
J. M. Cabrera
Keyword(s):  
Research Work ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Characterization ◽  
Low Carbon ◽  
Transformation Kinetics ◽  
Cooling Rates ◽  
Continuous Cooling Transformation ◽  
Continuous Cooling ◽  
Cct Diagrams

ABSTRACTThe aim of the present research work is to investigate the influence of B addition on the phase transformation kinetics under continuous cooling conditions. In order to perform this study, the behavior of two low carbon advanced ultra-high strength steels (A-UHSS) is analyzed during dilatometry tests over the cooling rate range of 0.1-200°C/s. The start and finish points of the austenite transformation are identified from the dilatation curves and then the continuous cooling transformation (CCT) diagrams are constructed. These diagrams are verified by microstructural characterization and Vickers micro-hardness. In general, results revealed that for slower cooling rates (0.1-0.5 °C/s) the present phases are mainly ferritic-pearlitic (F+P) structures. By contrast, a mixture of bainitic-martensitic structures predominates at higher cooling rates (50-200°C/s). On the other hand, CCT diagrams show that B addition delays the decomposition kinetics of austenite to ferrite, thereby promoting the formation of bainitic-martensitic structures. In the case of B microalloyed steel, the CCT curve is displaced to the right, increasing the hardenability. These results are associated with the ability of B atoms to segregate towards austenitic grain boundaries, which reduce the preferential sites for nucleation and development of F+P structures.

Evaluation of Formability Under Different Deformation Modes for TWIP900 Steel

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Suleyman Kilic ◽  
Fahrettin Ozturk
Keyword(s):  
Twip Steel ◽  
High Strength Steels ◽  
High Strength ◽  
Material Model ◽  
Deformation Analysis ◽  
Advanced High Strength Steels ◽  
Element Simulation ◽  
Springback Prediction ◽  
Deformation Modes ◽  
Prediction Capability

Automotive manufacturers always seek high strength and high formability materials for automotive bodies. Advanced high strength steels (AHSS) are excellent candidates for this purpose. These steels generally show a reasonable degree of formability, in addition to their high strength. One particular type is the twinning-induced plasticity (TWIP) steel, which is a high manganese austenite steel, and represents a second generation in AHSS. In this study, comprehensive deformation analysis of TWIP900CR steel including tensile, bending, Erichsen, and deep drawing of cylindrical cups tests is made. Finite element simulation of U and V shaped bending processes is also performed. Results indicate that the TWIP steel has good mechanical properties and high formability. However, springback is quite significant. The coining force should be considered in order to reduce the amount of springback. For springback prediction, it is found that the Yld2000-2d material model has better prediction capability than the Hill48 model.

scholarly journals Thermal Diffusivity of Traditional and Innovative Sheet Steels

2010 ◽  
Vol 297-301 ◽  
pp. 893-898
Author(s):  
Elena Campagnoli ◽  
Paolo Matteis ◽  
Giovanni M.M. Mortarino ◽  
Giorgio Scavino
Keyword(s):  
Thermal Diffusivity ◽  
Deep Drawing ◽  
Process Model ◽  
Twip Steel ◽  
Welding Process ◽  
High Strength Steels ◽  
High Strength ◽  
Carbon Steels ◽  
Low Carbon ◽  
Low Carbon Steels

The low carbon steels, used for the production of car bodies by deep drawing, are gradually substituted by high strength steels for vehicle weight reduction. The drawn car body components are joined by welding and the welded points undergo a reduction of the local tensile strength. In developing an accurate welding process model, able to optimized process parameters and to predict the final local microstructure, a significant improvement can be given by the knowledge of the welded steels thermal diffusivity at different temperatures. The laser-flash method has been used to compare the thermal diffusivity of two traditional deep drawing steels, two high strength steels already in common usage, i.e. a Dual Phase (DP) steel and a TRansformation Induced Plasticity (TRIP) steel, and one experimental high-Mn austenitic TWIP (Twinning Induced Plasticity) steel. The low carbon steels, at low temperatures, have a thermal diffusivity that is 4-5 times larger than the TWIP steel. Their thermal diffusivity decreases by increasing temperature while the TWIP steel shows an opposite behaviour, albeit with a lesser slope, so that above 700°C the TWIP thermal diffusivity is larger. The different behaviour of the TWIP steel in respect to the ferritic deep drawing steels arises from its non ferro-magnetic austenitic structure. The DP and TRIP steels show intermediate values, their diffusivity being lower than that of the traditional deep drawing steels; this latter fact probably arises from their higher alloy content and more complex microstructure.

SUSTAINABLE ULTRA-HIGH-PERFORMANCE GLASS CONCRETE FOR INFRASTRUCTURES

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Arezki Tagnit-Hamou ◽  
Nancy A. Soliman
Keyword(s):  
High Performance ◽  
Glass Powder ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Low Cost ◽  
Research Work ◽  
High Strength ◽  
Quartz Powder ◽  
Ultra High Performance Concrete ◽  
Powder Particles

This paper presents research work on the development of a green type of ultra-high-performance concrete using ground glass powders with different degrees of fineness (UHPGC). This article presents the development of an innovative, low-cost, and sustainable UHPGC through the use of glass powder to replace cement, and quartz powder particles. An UHPGC with a compressive strength (fc) of up to 220 MPa was prepared and its fresh, and mechanical properties were investigated. The test results indicate that the fresh UHPGC properties were improved when the cement and quartz powder were replaced with non-absorptive glass powder particles. The strength improvement can be attributed to the glass powder’s pozzolanicity and to its mechanical performance (very high strength and elastic modulus of glass). A case study of using this UHPGC is presented through the design and construction of a footbridge. Erection of footbridge at University of Sherbrooke Campus using UHPGC is also presented as a full-scale application.

Wear Resistance Research of Advanced High Strength Steels

2016 ◽  
Vol 850 ◽  
pp. 197-201
Author(s):  
Chao Zhi ◽  
Yi Fei Gong ◽  
Ai Min Zhao ◽  
Jian Guo He ◽  
Ran Ding
Keyword(s):  
Wear Resistance ◽  
Twip Steel ◽  
High Strength Steels ◽  
High Strength ◽  
Wear Performance ◽  
Dp Steel ◽  
Advanced High Strength Steels ◽  
Wear Mode ◽  
Surface Phase Transformation

The wear performance and wear mechanism under two-body abrasion of five advanced high strength steels, i.e. Nanobainite (NB) steel, Tempered Martensitic (TM) steel, Dual Phase (DP) steel, Transformation Induced Plasticity (TRIP) Steel and Twining Induced Plasticity (TWIP) steel were studied. By using the scanning electron microscopy (SEM), we investigated the wearing surface. Phase transformation strengthening behavior was also be discussed by analyzing the surface and sub-surface after abrasion. The results showed that micro-cutting was the major role of wear mode in the condition of two-body abrasion. In the circumstance of two-body abrasion, hardness was an important factor, the property of wear resistance enhanced while the hardness increased except for TM steel. NB steel possessed the best wear resistance which was 1.71 times higher than that of TWIP steel. The retained austenite transformed into martensite which can improve the hardness so that it enhanced the wear resistance of NB steel.

Sign in / Sign up

Export Citation Format

Share Document