The Effect of Silica Polymerization in Fly Ash on the Strength of Geopolymers

2014 ◽  
Vol 1611 ◽  
pp. 68-74 ◽  
Author(s):  
N. Koshukhova ◽  
I. Zhernovsky ◽  
K. Sobolev
Keyword(s):  
Fly Ash ◽  
Glass Phase ◽  
Degree Of Polymerization ◽  
Molar Ratio ◽  
Integral Parameter ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Wave Numbers ◽  
Different Sources

ABSTRACTThe formation of the structure of geopolymer binders based on low-calcium fly ash is a multifactorial process that depends on the degree of solubility of aluminosilicate components in the solution of alkali activator. It is observed that the geopolymer binders based on fly ash with an identical chemical and mineral composition, the same grain size, and also activated by the same alkalis can result in a different strength.This study is based on the assumption that there is dependence between the solubility of aluminosilicate components and the degree of polymerization of the silicates in glass phase. The degree of SiO2-polymerization is an integral parameter that is equal to the Si molar ratio (fSi) of the silicate component in the glass phase of fly ash. The degree of SiO2-polymerization can be estimated from the molar composition of glass phase, which is determined from the chemical composition and quantitative X-ray diffraction analysis including identification of the amorphous phase composition.The SiO2 polymerization rates of investigated fly ash specimens are confirmed by the IR results, specifically, by comparison of absorption bands of silicate fragments with varying levels of connectivity (Q0-4) in the range of wave numbers of 650–1350 cm-1.The comparative analysis of the correlation of 28-day strength of geopolymer binders based on fly ash from different sources and level of SiO2-polymerization demonstrated an inverse relationship with fSi molar ratio and compressive strength.

scholarly journals Can Inorganic Bovine Bone Grafts Present Distinct Properties?

2014 ◽  
Vol 25 (4) ◽  
pp. 282-288 ◽  
Author(s):  
Fernanda de Paula do Desterro ◽  
Márcia Soares Sader ◽  
Glória Dulce de Almeida Soares ◽  
Guaracilei Maciel Vidigal Jr
Keyword(s):  
Surface Area ◽  
Calcium Release ◽  
Physicochemical Characteristics ◽  
Molar Ratio ◽  
Nanoporous Structure ◽  
Bovine Bone ◽  
Ftir Analysis ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray

The aim of this study was to evaluate the physicochemical characteristics of 3 mineralized bovine inorganic biomaterials and correlate them with the dissolution rate. Bio-Oss(r), GenoxInorgânico(r), and Bonefill(r) were examined using field emission gun scanning electron microscopy (FEG-SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), specific surface area (BET), calcium/phosphorous molar ratio and a dissolution assay. Bio-Oss(r) showed a micro- and nanoporous structure consisting of 15-nm hydroxyapatite (HA) crystallites; Genox(r), a microporous structure composed of 39-nm HA crystallites; and Bonefill(r), micro- and nanoporous structure of indeterminable crystallite size. FTIR analysis showed that Bio-Oss(r) and Genox(r) were composed of calcium phosphate. The absorption bands of phosphate were poorly defined in Bonefill(r). By XRD, Bio-Oss(r) was shown to contain peaks related to the carbonated HA, whereas Genox(r) only contained peaks corresponding to HA. The broad bands in Bonefill(r) indicated low crystallinity. Bio-Oss(r) showed a greater surface area and calcium release rate than that of Genox(r). Although all biomaterials were of bovine origin, the different manufacturing processes result in materials with different physicochemical properties and may influence the biological and clinical response.

A Study on the Mechanism of Aluminia Extraction from Coal Fly Ash

2012 ◽  
Vol 518-523 ◽  
pp. 3109-3114 ◽  
Author(s):  
Miao Wang ◽  
Yan Xia Guo ◽  
Fang Qin Cheng ◽  
Yao Yao Li
Keyword(s):  
Fly Ash ◽  
Detailed Analysis ◽  
Coal Fly Ash ◽  
Degree Of Polymerization ◽  
X Ray Diffraction ◽  
Harmonious Development ◽  
X Ray ◽  
Iron Silicon ◽  
Aluminum Iron ◽  
High Degree

Coal fly ash contains large amounts of aluminum, iron, silicon and other useful elements. Its utilization effectively is of significance to harmonious development of economy, society and environment. However, coal fly ash is mainly composed of mullite and other inert glassy matters with high degree of polymerization and its reactivity is poor. So the fly ash needs to be activated before utilization. This article studied the effect of activation by calcination added with NaOH additives on aluminium extraction. The results showed that the addition of NaOH could improve the aluminium extraction rate evidently. Detailed analysis and characterization was carried out by using X-ray diffraction (XRD). The results indicated that NaOH could improve the depolymerization of vitreous.

Cd2+ and Cr3+ Cation Immobilization by Using Geopolymer Based on PT. IPMOMI Fly Ash

2016 ◽  
Vol 841 ◽  
pp. 186-192 ◽  
Author(s):  
Hamzah Fansuri ◽  
I’Is M. Anisatun ◽  
Anif Fatmawati ◽  
Wahyu Prasetyo Utomo ◽  
Warih Supriadi ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Inductively Coupled Plasma ◽  
Optical Emission ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Heavy Metal Cations ◽  
Geopolymer Paste

This study investigates the immobilization of Cd2+ and Cr3+ by using geopolymer paste based on PT. IPMOMI fly ash. The best composition of geopolimers paste was determined based on the highest magnitude of its 7 days compressive strength. Geopolymer pastes were prepared by varying SiO2/Al2O3 and Na2O/SiO2 molar ratio of the starting materials. X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) were employed to examined these compositions. The molar ratio of SiO2/Al2O3 6.46 was found to produce the highest compressive strength of the resulting geopolymer paste, i.e 25 MPa and increased to 33.17 MPa by adjusting the ratio of Na2O/SiO2 to 0.65. Cd2+ and Cr3+ cations were added into geopolymers resin at the level of 1000 – 16000 ppm (mg/kg fly ash) and it was found to improve their compressive strength. The addition of 4000 ppm of Cd2+ increased the compressive strength to 38.6 MPa while the inclusion of 6800 ppm of Cr3+ reached 47.83 MPa. Further addition of cations reduced these values and the lowest compressive strength was observed on the addition of 16000 ppm of Cd2+ and Cr3+, i.e 8.65 MPa and 4.39 MPa, respectively. Leaching test was conducted by using Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES) and the distribution of heavy metal cations were examined by using SEM-EDX. The results showed that geopolymer pastes were able to immobilize Cr3+ at the studied level as there was no trace of Cr3+ detected after 6.5 hours of leaching. Geopolymer pastes were also found to completely immobilize Cd2+ at the level of 1000 ppm albeit the addition of 16000 ppm results in 6.26% leached out of this cation.

Effect of Hydrated Metal Salts on the Coordination Product of Cobalt(II) halide and PNP Type Ligand, 2,6-bis(di-tertbutylphosphinomethyl) pyridine

2018 ◽  
Author(s):  
Tasneem Siddiquee ◽  
Abdul Goni
Keyword(s):  
Metal Salts ◽  
Molar Ratio ◽  
Pincer Complexes ◽  
Asymmetric Unit ◽  
X Ray Diffraction ◽  
Pincer Ligand ◽  
Tetrahedral Geometry ◽  
X Ray ◽  
Distorted Tetrahedral Geometry ◽  
Cobalt Center

Chemical treatment of CoX<sub>2</sub><b><sup>. </sup></b>6H<sub>2</sub>O (X = Cl, Br, I) with the potentially tridentate PNP pincer ligand 2,6-bis(di-<i>tert</i>-butylphosphinomethyl)pyridine in 1:1 molar ratio results in cobalt(II) halide-PNP pincer complexes. The effect of the hydrated metal source on molecular structure and geometry of the complexes was studied by single crystal X-ray diffraction analysis. The complexes are neutral and the cobalt center adopts a penta-coordinate system with potential atropisomerization. Within the unit cell there are two distinct molecules per asymmetric unit. One of the two phosphorus atoms in the PNP ligand was observed to be partially oxidized to phosphinoxide. Disorder in the structure reflects a mixture of square pyramidal and distorted tetrahedral geometry.

scholarly journals Photocatalytic Reduction of CO2 to Methanol Using a Copper-Zirconia Imidazolate Framework

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 346
Author(s):  
Sonam Goyal ◽  
Maizatul Shima Shaharun ◽  
Ganaga Suriya Jayabal ◽  
Chong Fai Kait ◽  
Bawadi Abdullah ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalyst Support ◽  
Oxidation Potential ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Optimum Parameters ◽  
Reduction Of Co2 ◽  
Enhanced Yield

A set of novel photocatalysts, i.e., copper-zirconia imidazolate (CuZrIm) frameworks, were synthesized using different zirconia molar ratios (i.e., 0.5, 1, and 1.5 mmol). The photoreduction process of CO2 to methanol in a continuous-flow stirred photoreactor at pressure and temperature of 1 atm and 25 °C, respectively, was studied. The physicochemical properties of the synthesized catalysts were studied using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectroscopy. The highest methanol activity of 818.59 µmol/L.g was recorded when the CuZrIm1 catalyst with Cu/Zr/Im/NH4OH molar ratio of 2:1:4:2 (mmol/mmol/mmol/M) was employed. The enhanced yield is attributed to the presence of Cu2+ oxidation state and the uniformly dispersed active metals. The response surface methodology (RSM) was used to optimize the reaction parameters. The predicted results agreed well with the experimental ones with the correlation coefficient (R2) of 0.99. The optimization results showed that the highest methanol activity of 1054 µmol/L.g was recorded when the optimum parameters were employed, i.e., stirring rate (540 rpm), intensity of light (275 W/m2) and photocatalyst loading (1.3 g/L). The redox potential value for the CuZrIm1 shows that the reduction potential is −1.70 V and the oxidation potential is +1.28 V for the photoreduction of CO2 to methanol. The current work has established the potential utilization of the imidazolate framework as catalyst support for the photoreduction of CO2 to methanol.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

Monitoring of Fluctuations in the Physical and Chemical Properties of a High-Calcium Fly Ash

1987 ◽  
Vol 113 ◽  
Author(s):  
Scott Schlorholtz ◽  
Ken Bergeson ◽  
Turgut Demirel
Keyword(s):  
Fly Ash ◽  
Chemical Properties ◽  
Operating Conditions ◽  
Physical And Chemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Studies ◽  
High Calcium ◽  
Physical And Chemical ◽  
And Chemical Properties

ABSTRACTThe physical and chemical properties of fly ash produced at Ottumwa Generating Station have been monitored since April, 1985. The fly ash is produced from burning a low sulfur, sub-bituminous coal obtained from the Powder River Basin near Gillette, Wyoming. One-hundred and sixty samples of fly ash were obtained during the two year period. All of the samples were subjected to physical testing as specified by ASTM C 311. About one-hundred of the samples were also subjected to a series of tests designed to monitor the self-cementing properties of the fly ash. Many of the fly ash samples were subjected to x-ray diffraction and fluorescence analysis to define the mineralogical and chemical composition of the bulk fly ash as a function of sampling date. Hydration products in selected hardened fly ash pastes, were studied by x-ray diffraction and scanning electron microscopy. The studies indicated that power plant operating conditions influenced the compressive strength of the fly ash paste specimens. Mineralogical and morphological studies of the fly ash pastes indicated that stratlingite formation occurred in the highstrength specimens, while ettringite was the major hydration product evident in the low-strength specimens.

Study on Influence of Silicate Morphology Based on pH Value

2012 ◽  
Vol 454 ◽  
pp. 324-328
Author(s):  
Yan He ◽  
Ya Jing Liu ◽  
Yong Lin Cao ◽  
Li Xia Zhou
Keyword(s):  
Silicic Acid ◽  
Ph Value ◽  
Colorimetric Method ◽  
Absorption Spectrometry ◽  
Degree Of Polymerization ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ph Values ◽  
The Stability

Infra-red absorption spectrometry, X-ray diffraction observations and characterization tests based on silicon molybdenum colorimetric method were used to investigate the optimal pH value controlling the stability of the silicic acid form. The experiment process was done by using sodium silicate as raw material. The results showed that the solution of silicate influenced the polymerization. The active silicic acid solution with a certain degree of polymerization was obtained by controlling the pH values.

Application of vermiculite and limestone to desulphurization and to the removal of dust during briquette combustion

2003 ◽  
Vol 67 (6) ◽  
pp. 1243-1251 ◽  
Author(s):  
A. Lu ◽  
D. Zhao ◽  
J. Li ◽  
C. Wang ◽  
S. Qin
Keyword(s):  
Electron Microscopy ◽  
Coal Combustion ◽  
Combustion Temperature ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Retention Ratio ◽  
X Ray ◽  
Major Factors ◽  
Chemical Reactant ◽  
Scanning Electron

AbstractSmall domestic cooking furnaces are widely used in China. These cooking furnaces release SO2 gas and dust into the atmosphere and cause serious air pollution. Experiments were conducted to investigate the effects of vermiculite, limestone or CaCO3, and combustion temperature and time on desulphurization and dust removal during briquette combustion in small domestic cooking furnaces. Additives used in the coal are vermiculite, CaCO3 and bentonite. Vermiculite is used for its expansion property to improve the contact between CaCO3 and SO2 and to convey O2 into the interior of briquette; CaCO3 is used as a chemical reactant to react with SO2 to form CaSO4; and bentonite is used to develop briquette strength. Expansion of vermiculite develops loose interior structures, such as pores or cracks, inside the briquette, and thus brings enough oxygen for combustion and sulphation reaction. Effective combustion of the original carbon reduces amounts of dust in the fly ash. X-ray diffraction, optical microscopy, and scanning electron microscopy with energy dispersive X-ray analysis show that S exists in the ash only as anhydrite CaSO4, a product of SO2 reacting with CaCO3 and O2. The formation of CaSO4 effectively reduces or eliminates SO2 emission from coal combustion. The major factors controlling S retention are vermiculite, CaCO3 and combustion temperature. The S retention ratio increases with increasing vermiculite amount at 950°C. The S retention ratio also increases with increasing Ca/S molar ratio, and the best Ca/S ratio is 2-3 for most combustion. With 12 g of the original coal, 1 to 2 g of vermiculite, a molar Ca/S ratio of 2.55 by adding CaCO3, and some bentonite, a S retention ratio >65% can be readily achieved. The highest S retention ratio of 97.9% is achieved at 950°C with addition of 2 g of vermiculite, a Ca/S ratio of 2.55 and bentonite.

scholarly journals Characterization of Fly Ash Generated from Matla Power Station in Mpumalanga, South Africa

2012 ◽  
Vol 9 (4) ◽  
pp. 1788-1795 ◽  
Author(s):  
Olushola S. Ayanda ◽  
Olalekan S. Fatoki ◽  
Folahan A. Adekola ◽  
Bhekumusa J. Ximba
Keyword(s):  
Fly Ash ◽  
Inductively Coupled Plasma ◽  
Coal Fly Ash ◽  
Harmful Effect ◽  
Point Of Zero Charge ◽  
X Ray Diffraction ◽  
Power Station ◽  
X Ray ◽  
Inductively Coupled ◽  
Plasma Mass Spectrometry

In this study, fly ash was obtained from Matla power station and the physicochemical properties investigated. The fly ash was characterized by x-ray fluorescence, x-ray diffraction, scanning electron microscopy, and inductively coupled plasma mass spectrometry. Surface area, particle size, ash and carbon contents, pH, and point of zero charge were also measured. The results showed that the fly ash is alkaline and consists mainly of mullite (Al6Si2O13) and quartz (SiO2). Highly toxic metals As, Sb, Cd, Cr, and Pb as well as metals that are essential to health in trace amounts were also present. The storage and disposal of coal fly ash can thus lead to the release of leached metals into soils, surface and ground waters, find way into the ecological systems and then cause harmful effect to man and its environments.

Sign in / Sign up

Export Citation Format

Share Document