Crystallization Kinetics of Plasma-Produced Amorphous Silicon Nanoparticles

2013 ◽  
Vol 1536 ◽  
pp. 213-218 ◽  
Author(s):  
Thomas Lopez ◽  
Lorenzo Mangolini

ABSTRACTThe use of a continuous flow non-thermal plasma reactor for the formation of silicon nanoparticles has attracted great interest because of the advantageous properties of the process [1]. Despite the short residence time in the plasma (around 10 milliseconds), a significant fraction of the precursor, silane, is converted and collected in the form of nanopowder. The structure of the produced powder can be tuned between amorphous and crystalline by adjusting the power of the radio-frequency excitation source, with higher power leading to the formation of crystalline particles. Numerical modeling suggests that higher excitation power results in a higher plasma density, which in turn increases the nanoparticle heating rate due to the interaction between ions, free radicals and the nanopowder suspended in the plasma [2]. While the experimental evidence suggests that plasma heating may be responsible for the formation of crystalline powder, an understanding of the mechanism that leads to the crystallization of the powder while in the plasma is lacking. In this work, we present an experimental investigation on the crystallization kinetic of plasma-produced amorphous powder. Silicon nanoparticles are nucleated and grown using a non-thermal plasma reactor similar to the one described in [1], but operated at low power to give amorphous nanoparticles in a 3-10 nm size range. The particles are then extracted from the reactor using an orifice and aerodynamically dragged into a low pressure reactor placed in a tube furnace capable of reaching temperatures up to 1000°C. Raman and TEM have been used to monitor the crystalline fraction of the material as a function of the residence time and temperature. It is expected that for a residence time in the annealing region of approximately ∼300 milliseconds, a temperature of at least 750 °C is needed to observe the onset of crystallization. A range of crystalline percentages can be observed from 750 °C to 830 °C. A discussion of particle growth and particle interaction, based on experimental evidence, will be presented with its relation to the overall effect on crystallization. Further data analysis allows extrapolating the crystallization rate for the case of this simple, purely thermal system. We conclude that thermal effects alone are not sufficient to explain the formation of crystalline powder in non-thermal plasma reactors.

PLoS ONE ◽  
2015 ◽  
Vol 10 (10) ◽  
pp. e0140897 ◽  
Author(s):  
Pouyan Talebizadeh ◽  
Hassan Rahimzadeh ◽  
Meisam Babaie ◽  
Saeed Javadi Anaghizi ◽  
Hamidreza Ghomi ◽  
...  

2019 ◽  
Vol 52 (25) ◽  
pp. 255201 ◽  
Author(s):  
T Xia ◽  
A Kleinheksel ◽  
E M Lee ◽  
Z Qiao ◽  
K R Wigginton ◽  
...  

Author(s):  
Daniel-Eusebiu Cretu ◽  
Radu Burlica ◽  
Oana Beniuga ◽  
Dragos Astanei ◽  
Catalin Rusu ◽  
...  

2014 ◽  
Vol 68 (3) ◽  
Author(s):  
Siti Musliha Aishah Musa ◽  
RK Raja Ibrahim ◽  
Asrul Izam Azmi

This paper presents early work on Fiber Bragg grating (FBG) as temperature sensor to monitor temperature variation inside a packed-bed non-thermal plasma reactor. FBG made from germania-doped fiber with center Bragg wavelength of 1552.5 nm was embedded inside non-thermal plasma reactor with sphere shape dielectric bead (barium titanate) and used to probe the temperature variation inside the reactor. The experimental works have proven that FBG is a suitable sensor to monitor temperature variation inside of reactor via LabVIEW program. Besides that, Optical Spectrum Analyzer (OSA) recorded Bragg wavelength shift as voltage of power supply increases, which indicate the non-uniform temperature variation occurring inside the reactor. However, it does not affect the chemical reaction inside the reactor because the temperature condition is in steady state.


Author(s):  
A. M. Vandenbroucke ◽  
R. Morent ◽  
N. De Geyter ◽  
C. Leys

AbstractThe aim of this paper is to give a review of the research on the decomposition of trichloroethylene (TCE), a common industrial solvent, with combined use of non-thermal plasma and heterogeneous catalysis, i.e. plasma-catalysis. This air purification technique has been investigated over the last decade in an effort to overcome the disadvantages of non-thermal plasma treatment of waste air containing volatile organic compounds (VOCs). Some examples of different plasma technologies used for plasma-catalysis are given. These include the dielectric barrier discharge, the pulsed corona discharge and the atmospheric pressure glow discharge. In a plasma-catalytic hybrid system the catalyst can either be located in the discharge region or downstream of the plasma reactor. The mechanisms that drive both configurations are briefly discussed, followed by an extended literature overview of the removal of TCE with plasma-catalysis.


Author(s):  
Piotr Krupski ◽  
Henryka Danuta Stryczewska

Purpose The research purpose of this paper is to confirm that internal overvoltages in the push–pull power inverter can be used to improve the discharge ignition in the gliding arc discharge (GAD) plasma reactor. Design/methodology/approach Investigations are based on the acquisition of voltage changes that occur together with the development of the discharge column and the imaging the GAD with the use of a high-speed camera. Findings The power supply has the distinctive feature of not having the switching overvoltages completely extinguished, as it is in typical push–pull inverters. The overvoltages still exist but only dangerous peaks are cut off. The remaining ones, of a dumped resonance character (Figure 3), are transferred to the secondary coil of the transformer. Correctly shaped overvoltages are used for ignition improvement in the GAD reactor. Practical implications GAD plasma reactors have many applications for pollution control, disinfection and sterilization of surfaces and for plasma deposition, surface functionalization, as well as in agricultural and medical treatment. Investigations prove the push–pull inverter’s advantages in comparison with the transformer-type power supply. Properly configured push–pull inverters have good ignition properties and control options, allowing to generate, desirable for many applications, homogeneous non-thermal plasma. Originality/value The idea of using switching overvoltages in transistors of push–pull switching-mode power supplies is new and has not been previously used to improve discharges ignition in a non-thermal plasma reactor.


2011 ◽  
Vol 13 (3) ◽  
pp. 206-212 ◽  
Author(s):  
Shinsuke Iijima ◽  
Morito Nakamura ◽  
Akira Yokoi ◽  
Mitsuhiro Kubota ◽  
Liwei Huang ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document