Light Management Using Periodic Textures for Enhancing Photocurrent and Conversion Efficiency in Thin-Film Silicon Solar Cells

2013 ◽  
Vol 1536 ◽  
pp. 3-15 ◽  
Author(s):  
Hitoshi Sai ◽  
Takuya Matsui ◽  
Adrien Bidiville ◽  
Takashi Koida ◽  
Yuji Yoshida ◽  
...  
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Aspect Ratio ◽  
Light Trapping ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Area Efficiency ◽  
Cell Thickness

ABSTRACTPeriodically textured back reflectors with hexagonal dimple arrays are applied to thin-film microcrystalline silicon (μc-Si:H) solar cells for enhancing light trapping. The period and aspect ratio of the honeycomb textures have a big impact on the photovoltaic performance. When the textures have a moderate aspect ratio, the optimum period for obtaining a high short circuit current density (JSC) is found to be equal to or slightly larger than the cell thickness. If the cell thickness exceeds the texture period, the cell surface tends to be flattened and texture-induced defects are generated, which constrain the improvement in JSC. Based on these findings, we have fabricated optimized μc-Si:H cells achieving a high active-area efficiency exceeding 11% and a JSC of 30 mA/cm2.

Nanoimprint Photonic Crystal Film Enhanced Light-Trapping in a-Si Thin Film Solar Cells

2011 ◽  
Vol 110-116 ◽  
pp. 497-502
Author(s):  
Wei Ping Chu ◽  
Fuh Shyang Juang ◽  
Jian Shian Lin ◽  
Tien Chai Lin ◽  
Chen Wei Kuo
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Photonic Crystals ◽  
Current Density ◽  
Light Trapping ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Thin Film Solar Cells ◽  
Uv Lamp

We utilize photonic crystals to enhanced lighttrapping in a-Si:H thin film solar cells. The photonic crystals effectively increase Haze ratio of glass and decrease reflectance of a-Si:H solar cells. Therefore, increase the photon path length to obtain maximum absorption of the absorber layer. The photonic crystals can effective in harvesting weakly absorbing photons with energies just above the band edge. We were spin coated UV glue on the glass, and then nanoimprint of photonic crystals pattern. Finally, used UV lamp was curing of UV glue on the glass. When the 45∘composite photonic crystals structures, the haze was increase to 87.9 %, resulting the short circuit current density and efficiency increasing to 13.96 mA/cm2 and 7.39 %, respectively. Because 45∘composite photonic crystals easy to focus on the point of light lead to the effect of scattering can’t achieve. So, we designs 90∘V-shaped photonic crystals structures to increase scattering. When the 90∘V-shaped photonic crystals structures, the Haze was increase to 93.9 %. Therefore, the short circuit current density and Efficiency increasing to 15.62 mA/cm2 and 8.09 %, respectively. We observed ~35 % enhancement of the short-circuit current density and ~31 % enhancement of the conversion efficiency.

scholarly journals The Influence of the Thickness of Compact TiO2 Electron Transport Layer on the Performance of Planar CH3NH3PbI3 Perovskite Solar Cells

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3295
Author(s):  
Andrzej Sławek ◽  
Zbigniew Starowicz ◽  
Marek Lipiński
Keyword(s):  
Solar Cells ◽  
Electron Transport ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
Precursor Solution ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Transport Layer ◽  
Electron Transport Layer

In recent years, lead halide perovskites have attracted considerable attention from the scientific community due to their exceptional properties and fast-growing enhancement for solar energy harvesting efficiency. One of the fundamental aspects of the architecture of perovskite-based solar cells (PSCs) is the electron transport layer (ETL), which also acts as a barrier for holes. In this work, the influence of compact TiO2 ETL on the performance of planar heterojunction solar cells based on CH3NH3PbI3 perovskite was investigated. ETLs were deposited on fluorine-doped tin oxide (FTO) substrates from a titanium diisopropoxide bis(acetylacetonate) precursor solution using the spin-coating method with changing precursor concentration and centrifugation speed. It was found that the thickness and continuity of ETLs, investigated between 0 and 124 nm, strongly affect the photovoltaic performance of PSCs, in particular short-circuit current density (JSC). Optical and topographic properties of the compact TiO2 layers were investigated as well.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

Numerical Simulation of Single Junction InGaN Solar Cell by SCAPS

2019 ◽  
Vol 821 ◽  
pp. 407-413 ◽  
Author(s):  
Mohamed Orabi Moustafa ◽  
Tariq Alzoubi
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Collection Efficiency ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Bandgap Energy ◽  
Single Junction

The performance of the InGaN single-junction thin film solar cells has been analyzed numerically employing the Solar Cell Capacitance Simulator (SCAPS-1D). The electrical properties and the photovoltaic performance of the InGaN solar cells were studied by changing the doping concentrations and the bandgap energy along with each layer, i.e. n-and p-InGaN layers. The results reveal an optimum efficiency of the InGaN solar cell of ~ 15.32 % at a band gap value of 1.32 eV. It has been observed that lowering the doping concentration NA leads to an improvement of the short circuit current density (Jsc) (34 mA/cm2 at NA of 1016 cm−3). This might be attributed to the increase of the carrier mobility and hence an enhancement in the minority carrier diffusion length leading to a better collection efficiency. Additionally, the results show that increasing the front layer thickness of the InGaN leads to an increase in the Jsc and to the conversion efficiency (η). This has been referred to the increase in the photogenerated current, as well as to the less surface recombination rate.

scholarly journals Benzothiadiazole Based Cascade Material to Boost the Performance of Inverted Ternary Organic Solar Cells

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 450 ◽  
Author(s):  
Miron Krassas ◽  
Christos Polyzoidis ◽  
Pavlos Tzourmpakis ◽  
Dimitriοs M. Kosmidis ◽  
George Viskadouros ◽  
...  
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Ring ◽  
Electron Cascade ◽  
First Time

A conjugated, ladder-type multi-fused ring 4,7-dithienbenzothiadiazole:thiophene derivative, named as compound ‘T’, was for the first time incorporated, within the PTB7:PC71BM photoactive layer for inverted ternary organic solar cells (TOSCs) realization. The effective energy level offset caused by compound T between the polymeric donor and fullerene acceptor materials, as well as its resulting potential as electron cascade material contribute to an enhanced exciton dissociation, electron transfer facilitator and thus improved overall photovoltaic performance. The engineering optimization of the inverted TOSC, ITO/PFN/PTB7:Compound T(5% v/v):PC71BM/MoO3/Al, resulted in an overall power conversion efficiency (PCE) of 8.34%, with a short-circuit current density (Jsc) of 16.75 mA cm−2, open-circuit voltage (Voc) of 0.74 V and a fill factor (FF) of 68.1%, under AM1.5G illumination. This photovoltaic performance was improved by approximately 12% with respect to the control binary device.

Preparation of the Three Main Layers of CdS/CdTe Thin Film Solar Cells Using a Single Vacuum System

2011 ◽  
Vol 378-379 ◽  
pp. 601-605 ◽  
Author(s):  
Saleh N. Alamri ◽  
M. S. Benghanem ◽  
A. A. Joraid
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Fused Silica ◽  
Vacuum System ◽  
Cdte Thin Film

This study investigates the preparation of the three main layers of a CdS/CdTe thin film solar cell using a single vacuum system. A Close Space Sublimation System was constructed to deposit CdS, CdTe and CdCl2 solar cell layers. Two hot plates were used to heat the source and the substrate. Three fused silica melting dishes were used as containers for the sources. The properties of the deposited CdS and CdTe films were determined via Atomic force microscopy, scanning electron microscopy, X-ray diffraction and optical transmission spectroscopy. An J-V characterization of the fabricated CdS/CdTe solar cells was performed under solar radiation. The short-circuit current density, Jsc, the open-circuit voltage, Voc, fill factor, FF and conversion efficiency, η, were measured and yielded values of 27 mA/cm2, 0.619 V, 58% and 9.8%, respectively.

Thermodynamic limits of nanophotonic light trapping in thin film silicon solar cells

2014 ◽  
Vol 92 (7/8) ◽  
pp. 909-912 ◽  
Author(s):  
Brian R. Maynard ◽  
E.A. Schiff
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Light Trapping ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Silicon Solar Cells ◽  
Thin Film Silicon ◽  
Solar Tracking ◽  
Current Densities ◽  
Thermodynamic Limits

We have extended an earlier thermodynamic treatment of light-trapping in lattice-textured solar cells to higher absorptances. This treatment is used to calculate the quantum efficiency spectra and short-circuit current densities JSC for thin-film silicon solar cells with ideal lattice textures. An optimal triangular lattice period of 900 nm yields a calculated JSC that is 2 mA/cm2 larger than for ideal random textures in a 1000 nm thick cell. We compare the calculations to recent experiments with periodically textured cells. While the experimental cells give JSC values that are comparable to the best cells with conventional textures, they do not show the features associated with the prediction of higher JSC. We discuss the role of imperfections in the periodic texturing, and suggest that cells used with solar tracking may realize the predicted JSC improvement.

scholarly journals Enhanced Light Trapping in Thin Film Solar Cells Using a Plasmonic Fishnet Structure

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Sayan Seal ◽  
Vinay Budhraja ◽  
Liming Ji ◽  
Vasundara V. Varadan
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Light Trapping ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Wire Mesh ◽  
Thin Film Solar Cells ◽  
Plasmonic Structures ◽  
Spacer Layer ◽  
High Absorption

Incorporating plasmonic structures into the back spacer layer of thin film solar cells (TFSCs) is an efficient way to improve their performance. The fishnet structure is used to enhance light trapping. Unlike other previously suggested discrete plasmonic particles, the fishnet is an electrically connected wire mesh that does not result in light field localization, which leads to high absorption losses. The design was verified experimentally. A silver fishnet structure was fabricated using electron beam lithography (EBL) and thermal evaporation. The final fabricated structure optically resembles a TFSC. The results predicted by numerical simulations were reproduced experimentally on a fabricated sample. We show that light absorption in the a-Si absorber layer is enhanced by a factor of 10.6 at the design wavelength of 690 nm due to the presence of the fishnet structure. Furthermore, the total absorption over all wavelengths was increased by a factor of 3.2. The short-circuit current of the TFSC was increased by 30% as a result of including the fishnet.

HYBRID ORGANIC SOLAR CELLS BLENDED WITH CNTs

2015 ◽  
Vol 22 (06) ◽  
pp. 1550072
Author(s):  
SUDIP ADHIKARI ◽  
HIDEO UCHIDA ◽  
MASAYOSHI UMENO
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photovoltaic Device ◽  
Device Fabrication ◽  
Walled Cnts

In this paper, composite carbon nanotubes (C-CNTs); single-walled CNTs (SWCNTs) and multi-walled CNTs (MWCNTs) are synthesized using an ultrasonic nebulizer in a large quartz tube for photovoltaic device fabrication in poly-3-octyl-thiophene (P3OT)/ n - Si heterojunction solar cells. We found that the device fabricated with C-CNTs shows much better photovoltaic performance than that of a device without C-CNTs. The device with C-CNTs shows open-circuit voltage (Voc) of 0.454 V, a short circuit current density (Jsc) of 12.792 mA/cm2, fill factor (FF) of 0.361 and power conversion efficiency of 2.098 %. Here, we proposed that SWCNTs and MWCNTs provide efficient percolation paths for both electron and hole transportation to opposite electrodes and leading to the suppression of charge carrier recombination, thereby increasing the photovoltaic device performance.

Sign in / Sign up

Export Citation Format

Share Document