Effects of VUV and EUV Radiation on Ultra Low-k Materials Damage

2013 ◽  
Vol 1559 ◽  
Author(s):  
Oleg Braginsky ◽  
Alexander Kovalev ◽  
Dmitry Lopaev ◽  
Yury Mankelevich ◽  
Olga Proshina ◽  
...  

ABSTRACTLow-k dielectric films can be substantially damaged during plasma processing. High energy UV and VUV photons emitted by plasma play the key role in damaging the porous low-k films directly or indirectly by stimulating chemical reactions with radicals in plasma and plasma afterglow. The different ULK samples (k: 2.0-2.2, porosity: 30-50%, pore radius: 1-2 nm) were studied by exposing to five radiation sources at various wavelengths (VUV: 193 nm, 147 nm, 104-106 nm, 58.3 nm, and EUV: 13.5 nm). Time-spatial behavior of the ULK damage as a function of photons fluence was studied by FTIR spectroscopy and XRF analysis. It is shown that the degree of damage depends on wavelength of UV light. The major UV damage was observed at the wavelengths below 193 nm. The maximum damage corresponds to 147 nm while the degree of damage at 58.3 nm was much smaller. In the case of organosilicate (OSG) based ULK materials, the degree of damage, as a rule, increases with porosity. Organic low-k materials are damaged more than OSG at 193 nm, but at shorter wavelengths (147, 106, 58.3 and 13.5 nm) they are more stable than OSG. One-dimensional model for radiation absorption and dynamics of CH3 group destruction in ULK films was developed. The cross-sections of photons absorption and photo-stimulated Si-CH3 bond breaking in ULK films for 13.5 -147 nm wavelength range were derived from a combined experimental and modeling study. The obtained values allow to simulate the VUV/EUV induced modifications of low-k materials with different composition, to understand better the mechanisms of plasma damage and to generate ideas for controllable modifications of low-k materials.

2006 ◽  
Vol 914 ◽  
Author(s):  
Thomas Abell ◽  
Jeffrey Lee ◽  
Mansour Moinpour

AbstractThe implementation of porous low-k and ultra-low k dielectrics to reduce RC delay in integrated circuit interconnect wiring has been fraught with numerous challenges. The obvious challenges of materials design and preservation of the desired electrical and mechanical properties upon subsequent processing have been significant. The vulnerability of these films to damage from fast ion and radiation damage will be discussed in the context of post-deposition processing (including low-k cure and plasma processing damage). This paper attempts to review the challenges associated with destructive and non-destructive measurement of low k dielectric films with respect to underlying physical principles of the metrology. Metrology techniques, assumed to be non-destructive based on experience with dense silicon dioxide, will be discussed with regards to newer and more fragile low-k dielectric films.


2005 ◽  
Vol 863 ◽  
Author(s):  
Thomas Abell ◽  
Kristof Houthoofd ◽  
Francesca Iacopi ◽  
Piet Grobet ◽  
Karen Maex

Abstract29Si magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy was employed to characterize short-range atomic structure modifications to low k dielectric films that were subjected to post-deposition plasma exposure or UV curing. Comparison of spectra from single thick depositions of a CVD low k film (k∼3.0) with sequential thin depositions of the same film revealed ∼3% increase in Si-O crosslinking that was attributed to interfacial plasma damage. Comparison of a second CVD low k film (k∼3.0) before and after UV curing revealed ∼11% increase in Si-O crosslinking with commensurate losses of Si-OH and Si-CH3 groups. UV curing was believed to result in bulk modification. This crosslinking was found to increase the Young's modulus of the film from 11 to 16 GPa as measured on 700 nm films by nanoindentation. NMR analysis was found to provide significant information beyond that provided by FTIR but required special sample preparation and extensive data collection.


Author(s):  
D. Zudhistira ◽  
V. Viswanathan ◽  
V. Narang ◽  
J.M. Chin ◽  
S. Sharang ◽  
...  

Abstract Deprocessing is an essential step in the physical failure analysis of ICs. Typically, this is accomplished by techniques such as wet chemical methods, RIE, and mechanical manual polishing. Manual polishing suffers from highly non-uniform delayering particularly for sub 20nm technologies due to aggressive back-end-of-line scaling and porous ultra low-k dielectric films. Recently gas assisted Xe plasma FIB has demonstrated uniform delayering of the metal and dielectric layers, achieving a planar surface of heterogeneous materials. In this paper, the successful application of this technique to delayer sub-20 nm microprocessor chips with real defects to root cause the failure is presented.


2018 ◽  
Author(s):  
K. A. Rubin ◽  
W. Jolley ◽  
Y. Yang

Abstract Scanning Microwave Impedance Microscopy (sMIM) can be used to characterize dielectric thin films and to quantitatively discern film thickness differences. FEM modeling of the sMIM response provides understanding of how to connect the measured sMIM signals to the underlying properties of the dielectric film and its substrate. Modeling shows that sMIM can be used to characterize a range of dielectric film thicknesses spanning both low-k and medium-k dielectric constants. A model system consisting of SiO2 thin films of various thickness on silicon substrates is used to illustrate the technique experimentally.


2021 ◽  
Vol 2021 (1) ◽  
Author(s):  
Roman N. Lee ◽  
Alexey A. Lyubyakin ◽  
Vyacheslav A. Stotsky

Abstract Using modern multiloop calculation methods, we derive the analytical expressions for the total cross sections of the processes e−γ →$$ {e}^{-}X\overline{X} $$ e − X X ¯ with X = μ, γ or e at arbitrary energies. For the first two processes our results are expressed via classical polylogarithms. The cross section of e−γ → e−e−e+ is represented as a one-fold integral of complete elliptic integral K and logarithms. Using our results, we calculate the threshold and high-energy asymptotics and compare them with available results.


1957 ◽  
Vol 35 (1) ◽  
pp. 21-37 ◽  
Author(s):  
J. D. Jackson

The Monte Carlo calculations of McManus and Sharp (unpublished) for the prompt nuclear processes occurring upon bombardment of heavy elements by 400 Mev. protons are combined with a description of the subsequent neutron evaporation to determine spallation cross sections for comparison with experiment. The model employed is a schematic one which suppresses the detailed characteristics of individual nuclei, but gives the over-all behavior to be expected. Many-particle and collective effects such as alpha particle emission and fission are ignored. The computed cross sections are presented in a variety of different graphical forms which illustrate quantitatively the qualitative picture of high energy reactions first given by Serber (1947). The calculations are in general agreement with existing data when fission is not an important effect, but the agreement does not imply a very stringent test of the various features of the model.


2020 ◽  
Vol 2020 (9) ◽  
Author(s):  
Antonio Costantini ◽  
Federico De Lillo ◽  
Fabio Maltoni ◽  
Luca Mantani ◽  
Olivier Mattelaer ◽  
...  

Abstract High-energy lepton colliders with a centre-of-mass energy in the multi-TeV range are currently considered among the most challenging and far-reaching future accelerator projects. Studies performed so far have mostly focused on the reach for new phenomena in lepton-antilepton annihilation channels. In this work we observe that starting from collider energies of a few TeV, electroweak (EW) vector boson fusion/scattering (VBF) at lepton colliders becomes the dominant production mode for all Standard Model processes relevant to studying the EW sector. In many cases we find that this also holds for new physics. We quantify the size and the growth of VBF cross sections with collider energy for a number of SM and new physics processes. By considering luminosity scenarios achievable at a muon collider, we conclude that such a machine would effectively be a “high-luminosity weak boson collider,” and subsequently offer a wide range of opportunities to precisely measure EW and Higgs couplings as well as discover new particles.


2021 ◽  
Vol 2021 (7) ◽  
Author(s):  
E. Iancu ◽  
A. H. Mueller ◽  
D. N. Triantafyllopoulos ◽  
S. Y. Wei

Abstract Using the dipole picture for electron-nucleus deep inelastic scattering at small Bjorken x, we study the effects of gluon saturation in the nuclear target on the cross-section for SIDIS (single inclusive hadron, or jet, production). We argue that the sensitivity of this process to gluon saturation can be enhanced by tagging on a hadron (or jet) which carries a large fraction z ≃ 1 of the longitudinal momentum of the virtual photon. This opens the possibility to study gluon saturation in relatively hard processes, where the virtuality Q2 is (much) larger than the target saturation momentum $$ {Q}_s^2 $$ Q s 2 , but such that z(1 − z)Q2 ≲ $$ {Q}_s^2 $$ Q s 2 . Working in the limit z(1 − z)Q2 ≪ $$ {Q}_s^2 $$ Q s 2 , we predict new phenomena which would signal saturation in the SIDIS cross-section. For sufficiently low transverse momenta k⊥ ≪ Qs of the produced particle, the dominant contribution comes from elastic scattering in the black disk limit, which exposes the unintegrated quark distribution in the virtual photon. For larger momenta k⊥ ≳ Qs, inelastic collisions take the leading role. They explore gluon saturation via multiple scattering, leading to a Gaussian distribution in k⊥ centred around Qs. When z(1 − z)Q2 ≪ Q2, this results in a Cronin peak in the nuclear modification factor (the RpA ratio) at moderate values of x. With decreasing x, this peak is washed out by the high-energy evolution and replaced by nuclear suppression (RpA< 1) up to large momenta k⊥ ≫ Qs. Still for z(1 − z)Q2 ≪ $$ {Q}_s^2 $$ Q s 2 , we also compute SIDIS cross-sections integrated over k⊥. We find that both elastic and inelastic scattering are controlled by the black disk limit, so they yield similar contributions, of zeroth order in the QCD coupling.


2021 ◽  
Vol 13 (4) ◽  
pp. 598
Author(s):  
Daniel O. Wasonga ◽  
Afrane Yaw ◽  
Jouko Kleemola ◽  
Laura Alakukku ◽  
Pirjo S.A. Mäkelä

Cassava has high energy value and rich nutritional content, yet its productivity in the tropics is seriously constrained by abiotic stresses such as water deficit and low potassium (K) nutrition. Systems that allow evaluation of genotypes in the field and greenhouse for nondestructive estimation of plant performance would be useful means for monitoring the health of plants for crop-management decisions. We investigated whether the red–green–blue (RGB) and multispectral images could be used to detect the previsual effects of water deficit and low K in cassava, and whether the crop quality changes due to low moisture and low K could be observed from the images. Pot experiments were conducted with cassava cuttings. The experimental design was a split-plot arranged in a completely randomized design. Treatments were three irrigation doses split into various K rates. Plant images were captured beginning 30 days after planting (DAP) and ended at 90 DAP when plants were harvested. Results show that biomass, chlorophyll, and net photosynthesis were estimated with the highest accuracy (R2 = 0.90), followed by leaf area (R2 = 0.76). Starch, energy, carotenoid, and cyanide were also estimated satisfactorily (R2 > 0.80), although cyanide showed negative regression coefficients. All mineral elements showed lower estimation accuracy (R2 = 0.14–0.48) and exhibited weak associations with the spectral indices. Use of the normalized difference vegetation index (NDVI), green area (GA), and simple ratio (SR) indices allowed better estimation of growth and key nutritional traits. Irrigation dose 30% of pot capacity enriched with 0.01 mM K reduced most index values but increased the crop senescence index (CSI). Increasing K to 16 mM over the irrigation doses resulted in high index values, but low CSI. The findings indicate that RGB and multispectral imaging can provide indirect measurements of growth and key nutritional traits in cassava. Hence, they can be used as a tool in various breeding programs to facilitate cultivar evaluation and support management decisions to avert stress, such as the decision to irrigate or apply fertilizers.


2003 ◽  
Vol 766 ◽  
Author(s):  
Jin-Heong Yim ◽  
Jung-Bae Kim ◽  
Hyun-Dam Jeong ◽  
Yi-Yeoul Lyu ◽  
Sang Kook Mah ◽  
...  

AbstractPorous low dielectric films containing nano pores (∼20Å) with low dielectric constant (<2.2), have been prepared by using various kinds of cyclodextrin derivatives as porogenic materials. The pore structure such as pore size and interconnectivity can be controlled by changing functional groups of the cyclodextrin derivatives. We found that mechanical properties of porous low-k thin film prepared with mCSSQ (modified cyclic silsesquioxane) precursor and cyclodextrin derivatives were correlated with the pore interconnection length. The longer the interconnection length of nanopores in the thin film, the worse the mechanical properties of the thin film (such as hardness and modulus) even though the pore diameter of the films were microporous (∼2nm).


Sign in / Sign up

Export Citation Format

Share Document