Oxidation state of tungsten oxide thin films used as gate dielectric for zinc oxide based transistors

2012 ◽  
Vol 1494 ◽  
pp. 111-114
Author(s):  
Michael Lorenz ◽  
Marius Grundmann ◽  
Sandra Wickert ◽  
Reinhard Denecke
Keyword(s):  
Thin Films ◽  
Tungsten Oxide ◽  
Photoelectron Spectroscopy ◽  
Gate Dielectric ◽  
Field Effect Transistors ◽  
Stoichiometric Ratio ◽  
Electrical And Optical Properties ◽  
Metal Insulator ◽  
X Ray ◽  
Tungsten Oxide Thin Films

ABSTRACTWe present an investigation of the degree of oxidization of tungsten oxide (WOx) thin films used as gate dielectric for metal-insulator-semiconductor field-effect transistors (MISFET). By means of X-ray photoelectron spectroscopy WOx thin films grown by pulsed-laser deposition at room temperature were investigated. The electrical and optical properties depend significantly on the oxygen pressure during deposition and are affected by the stoichiometric ratio of oxygen and tungsten.

Structural, Magnetic and Magneto-tranport Properties of Reactive-sputtered Fe3O4 Thin Films

2010 ◽  
Vol 1250 ◽  
Author(s):  
Xinghua Wang ◽  
Sarjoosing Goolaup ◽  
Peng Ren ◽  
Wen Siang Lew
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Single Phase ◽  
Native Oxide ◽  
X Ray Diffraction ◽  
Verwey Transition ◽  
Electrical Measurements ◽  
Metal Insulator ◽  
X Ray ◽  
Sample Measurement

AbstractThin films of magnetite (Fe3O4) are grown on a single-crystal Si/SiO2 (100) substrate with native oxide using DC reactive sputtering technique at room tempreture (RT) and 300C. The x-ray diffraction(XRD) result shows the thermal energy during deposition enhances the crystallization of the Fe3O4 and x-ray photoelectron spectroscopy confirms the film deposited at 300C is single-phase Fe3O4 while the film deposited at RT is mostly ν-Fe2O3. The electrical measurements show that the resistivity of the Fe3O4 film increases exponentially with decreasing temperature, and exhibit a sharp metal-insulator transition at around 100 K, indicating the Verwey transition feature. The saturation magnetization Ms of Fe3O4 film measured by vibrating sample measurement (VSM) at RT was found to be 445 emu/cm3.

Molecular Precursors to Boron Nitride then Films: the Reactions of Diborane with Ammonia and with Hydrazine on Ru(0001)

1991 ◽  
Vol 250 ◽  
Author(s):  
Charles M. Truong ◽  
José A. Rodriguez ◽  
Ming Cheng Wu ◽  
D. W. Goodman
Keyword(s):  
Thin Films ◽  
Low Temperature ◽  
Boron Nitride ◽  
Mass Spectroscopy ◽  
Photoelectron Spectroscopy ◽  
Stoichiometric Ratio ◽  
X Ray ◽  
Molecular Precursors ◽  
Temperature Deposition ◽  
Boron Nitrogen

AbstractThe coadsorption and reaction of diborane with ammonia and with hydrazine on Ru(0001) have been studied using X-ray photoelectron spectroscopy (XPS) and thermal desorption mass spectroscopy (TDS). Diborane is found to decompose to atomic boron and hydrogen upon adsorption at T>200K. Multilayers of diborane and ammonia, deposited at 90K on Ru(0001), react when annealed to 600K. The XPS results indicate that boron-nitrogen adlayers can be formed by this reaction. These boron-nitrogen films are boron-rich and.decompose at temperatures higher than 1100K. Our TDS studies reveal that hydrazine decomposes extensively to NH3, N2, N and H on Ru(0001). Due to its higher reactivity, boron-nitrogen films of B/N stoichiometric ratio near unity are obtained when hydrazine is used rather than ammonia. In our studies, these films were formed by either simultaneously dosing B2H6 and N2H4 at 450K or by coadsorption of the reactants at 90K and subsequent annealing to 450K. These studies have shown that diborane and hydrazine can be successfully used as molecular precursors in the low temperature deposition of boron nitride thin-films.

scholarly journals Structural and tribological properties of tungsten oxide thin film on a silicon substrate

2020 ◽  
Vol 44 (11-12) ◽  
pp. 744-749
Author(s):  
Siamak Ziakhodadadian ◽  
Tianhui Ren
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Substrate Temperature ◽  
Tungsten Oxide ◽  
Oxide Thin Film ◽  
X Ray Diffraction ◽  
Oxide Thin Films ◽  
X Ray ◽  
Tungsten Oxide Thin Films ◽  
Scanning Electron

In this work, tungsten oxide thin films are deposited on silicon substrates using the hot filament chemical vapor deposition system. The influence of substrate temperature on the structural, morphological, and elemental composition of the tungsten oxide thin films is investigated using X-ray diffraction, field-emission scanning electron microscopy, and X-ray photoelectron spectroscopy techniques. Also, the mechanical and tribological properties of these thin films are considered using nanoindentation and scratch tests. Based on X-ray diffraction results, it can be concluded that tungsten oxide thin films are synthesized with a cubic WO3 structure. From field-emission scanning electron microscopy images, it can be seen that tungsten oxide thin films are made of crystal clusters which have grown vertically on the substrate surface. In addition, the results exhibit two asymmetric W4d5/2 and W4d7/2 peaks which can be assigned to W5+ and W4+ species, respectively. The mechanical results show that the hardness and the elastic modulus increase on raising the substrate temperature up to 600 °C. From the tribological performances, the friction coefficient of the tungsten oxide thin film decreases on increasing the substrate temperature.

scholarly journals Analysis of Metal-Insulator Crossover in Strained SrRuO3 Thin Films by X-ray Photoelectron Spectroscopy

Coatings ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 780
Author(s):  
Andrea Nardi ◽  
Chiara Bigi ◽  
Sandeep Kumar Chaluvadi ◽  
Regina Ciancio ◽  
Jun Fujii ◽  
...  
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Compressive Strain ◽  
Binding Energies ◽  
Perovskite Oxide ◽  
Strontium Ruthenate ◽  
Metal Insulator ◽  
X Ray ◽  
Epitaxial Strain ◽  
Extra Peak

The electronic properties of strontium ruthenate SrRuO3 perovskite oxide thin films are modified by epitaxial strain, as determined by growing on different substrates by pulsed laser deposition. Temperature dependence of the transport properties indicates that tensile strain deformation of the SrRuO3 unit cell reduces the metallicity of the material as well as its metal-insulator-transition (MIT) temperature. On the contrary, the shrinkage of the Ru–O–Ru buckling angle due to compressive strain is counterweighted by the increased overlap of the conduction Ru-4d orbitals with the O-2p ones due to the smaller interatomic distances resulting into an increased MIT temperature, i.e., a more conducting material. In particular, in the more metallic samples, the core level X-ray photoemission spectroscopy lineshapes show the occurrence of an extra-peak at the lower binding energies of the main Ru-3d peak that is attributed to screening, as observed in volume sensitive photoemission of the unstrained material.

Phase configuration, nanostructure, and mechanical behaviors in Ti-B-C-N thin films

2009 ◽  
Vol 24 (8) ◽  
pp. 2520-2527 ◽  
Author(s):  
Yonghao Lu ◽  
Junping Wang ◽  
Yaogen Shen ◽  
Dongbai Sun
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Solid Solution Hardening ◽  
Mechanical Behaviors ◽  
Additional Increase ◽  
N Content ◽  
X Ray ◽  
Nanocomposite Thin Films ◽  
The Cost ◽  
Nano Grains

A series of Ti-B-C-N thin films were deposited on Si (100) at 500 °C by incorporation of different amounts of N into Ti-B-C using reactive unbalanced dc magnetron sputtering in an Ar-N2 gas mixture. The effect of N content on phase configuration, nanostructure evolution, and mechanical behaviors was studied by x-ray diffraction, x-ray photoelectron spectroscopy, Raman spectroscopy, high-resolution transmission electron microscopy, and microindentation. It was found that the pure Ti-B-C was two-phased quasi-amorphous thin films comprising TiCx and TiB2. Incorporation of a small amount of N not only dissolved into TiCx but also promoted growth of TiCx nano-grains. As a result, nanocomposite thin films of nanocrystalline (nc-) TiCx(Ny) (x + y < 1) embedded into amorphous (a-) TiB2 were observed until nitrogen fully filled all carbon vacancy lattice (at that time x + y = 1). Additional increase of N content promoted formation of a-BN at the cost of TiB2, which produced nanocomposite thin films of nc-Ti(Cx,N1-x) embedded into a-(TiB2, BN). Formation of BN also decreased nanocrystalline size. Both microhardness and elastic modulus values were increased with an increase of N content and got their maximums at nanocomposite thin films consisting of nc-Ti(Cx,N1-x) and a-TiB2. Both values were decreased after formation of BN. Residual compressive stress value was successively decreased with an increase of N content. Enhancement of hardness was attributed to formation of nanocomposite structure and solid solution hardening.

Nitrogen (N2) Implantation to Suppress Growth of Interfacial Oxide in Mocvd Bst and Sputtered Bst Films

1999 ◽  
Vol 567 ◽  
Author(s):  
Renee Nieh ◽  
Wen-Jie Qi ◽  
Yongjoo Jeon ◽  
Byoung Hun Lee ◽  
Aaron Lucas ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Interfacial Layer ◽  
Gate Dielectric ◽  
Nitrogen Concentration ◽  
Chemical Vapor ◽  
Future Generation ◽  
Oxide Thickness ◽  
Layer Growth ◽  
X Ray ◽  
Bst Films

ABSTRACTBa0.5Sr0.5TiO3 (BST) is one of the high-k candidates for replacing SiO2 as the gate dielectric in future generation devices. The biggest obstacle to scaling the equivalent oxide thickness (EOT) of BST is an interfacial layer, SixOy, which forms between BST and Si. Nitrogen (N2) implantation into the Si substrate has been proposed to reduce the growth of this interfacial layer. In this study, capacitors (Pt/BST/Si) were fabricated by depositing thin BST films (50Å) onto N2 implanted Si in order to evaluate the effects of implant dose and annealing conditions on EOT. It was found that N2 implantation reduced the EOT of RF magnetron sputtered and Metal Oxide Chemical Vapor Deposition (MOCVD) BST films by ∼20% and ∼33%, respectively. For sputtered BST, an implant dose of 1×1014cm−;2 provided sufficient nitrogen concentration without residual implant damage after annealing. X-ray photoelectron spectroscopy data confirmed that the reduction in EOT is due to a reduction in the interfacial layer growth. X-ray diffraction spectra revealed typical polycrystalline structure with (111) and (200) preferential orientations for both films. Leakage for these 50Å BST films is on the order of 10−8 to 10−5 A/cm2—lower than oxynitrides with comparable EOTs.

scholarly journals Optical Constant and Conformality Analysis of SiO2 Thin Films Deposited on Linear Array Microstructure Substrate by PECVD

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 510
Author(s):  
Yongqiang Pan ◽  
Huan Liu ◽  
Zhuoman Wang ◽  
Jinmei Jia ◽  
Jijie Zhao
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Deposition Rate ◽  
Optical Constant ◽  
Photoelectron Spectroscopy ◽  
Linear Array ◽  
Chemical Vapor ◽  
Rf Plasma ◽  
X Ray ◽  
Sio2 Thin Film

SiO2 thin films are deposited by radio frequency (RF) plasma-enhanced chemical vapor deposition (PECVD) technique using SiH4 and N2O as precursor gases. The stoichiometry of SiO2 thin films is determined by the X-ray photoelectron spectroscopy (XPS), and the optical constant n and k are obtained by using variable angle spectroscopic ellipsometer (VASE) in the spectral range 380–1600 nm. The refractive index and extinction coefficient of the deposited SiO2 thin films at 500 nm are 1.464 and 0.0069, respectively. The deposition rate of SiO2 thin films is controlled by changing the reaction pressure. The effects of deposition rate, film thickness, and microstructure size on the conformality of SiO2 thin films are studied. The conformality of SiO2 thin films increases from 0.68 to 0.91, with the increase of deposition rate of the SiO2 thin film from 20.84 to 41.92 nm/min. The conformality of SiO2 thin films decreases with the increase of film thickness, and the higher the step height, the smaller the conformality of SiO2 thin films.

scholarly journals A novel and potentially scalable CVD-based route towards SnO2:Mo thin films as transparent conducting oxides

2021 ◽  
Author(s):  
Tianlei Ma ◽  
Marek Nikiel ◽  
Andrew G. Thomas ◽  
Mohamed Missous ◽  
David J. Lewis
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Mixed Valence ◽  
Chemical Vapour ◽  
X Ray Diffraction ◽  
X Ray ◽  
Conducting Oxides ◽  
Valence States ◽  
3 Omega ◽  
First Time

AbstractIn this report, we prepared transparent and conducting undoped and molybdenum-doped tin oxide (Mo–SnO2) thin films by aerosol-assisted chemical vapour deposition (AACVD). The relationship between the precursor concentration in the feed and in the resulting films was studied by energy-dispersive X-ray spectroscopy, suggesting that the efficiency of doping is quantitative and that this method could potentially impart exquisite control over dopant levels. All SnO2 films were in tetragonal structure as confirmed by powder X-ray diffraction measurements. X-ray photoelectron spectroscopy characterisation indicated for the first time that Mo ions were in mixed valence states of Mo(VI) and Mo(V) on the surface. Incorporation of Mo6+ resulted in the lowest resistivity of $$7.3 \times 10^{{ - 3}} \Omega \,{\text{cm}}$$ 7.3 × 10 - 3 Ω cm , compared to pure SnO2 films with resistivities of $$4.3\left( 0 \right) \times 10^{{ - 2}} \Omega \,{\text{cm}}$$ 4.3 0 × 10 - 2 Ω cm . Meanwhile, a high transmittance of 83% in the visible light range was also acquired. This work presents a comprehensive investigation into impact of Mo doping on SnO2 films synthesised by AACVD for the first time and establishes the potential for scalable deposition of SnO2:Mo thin films in TCO manufacturing. Graphical abstract

scholarly journals X-ray Photoelectron Spectroscopy Analysis of Chitosan–Graphene Oxide-Based Composite Thin Films for Potential Optical Sensing Applications

Polymers ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 478
Author(s):  
Wan Mohd Ebtisyam Mustaqim Mohd Daniyal ◽  
Yap Wing Fen ◽  
Silvan Saleviter ◽  
Narong Chanlek ◽  
Hideki Nakajima ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Functional Group ◽  
Optical Sensing ◽  
Composite Thin Films ◽  
Cobalt Ions ◽  
X Ray ◽  
Sensing Applications

In this study, X-ray photoelectron spectroscopy (XPS) was used to study chitosan–graphene oxide (chitosan–GO) incorporated with 4-(2-pyridylazo)resorcinol (PAR) and cadmium sulfide quantum dot (CdS QD) composite thin films for the potential optical sensing of cobalt ions (Co2+). From the XPS results, it was confirmed that carbon, oxygen, and nitrogen elements existed on the PAR–chitosan–GO thin film, while for CdS QD–chitosan–GO, the existence of carbon, oxygen, cadmium, nitrogen, and sulfur were confirmed. Further deconvolution of each element using the Gaussian–Lorentzian curve fitting program revealed the sub-peak component of each element and hence the corresponding functional group was identified. Next, investigation using surface plasmon resonance (SPR) optical sensor proved that both chitosan–GO-based thin films were able to detect Co2+ as low as 0.01 ppm for both composite thin films, while the PAR had the higher binding affinity. The interaction of the Co2+ with the thin films was characterized again using XPS to confirm the functional group involved during the reaction. The XPS results proved that primary amino in the PAR–chitosan–GO thin film contributed more important role for the reaction with Co2+, as in agreement with the SPR results.

Sign in / Sign up

Export Citation Format

Share Document