Influence of different casting processes on high cycle fatigue behavior of Mg–10Gd–3Y–0.5Zr alloy

2016 ◽  
Vol 31 (16) ◽  
pp. 2538-2548 ◽  
Author(s):  
Jimei Mao ◽  
Wencai Liu ◽  
Yanlei Li ◽  
Guangling Wei ◽  
Liang Zhang ◽  
...  
Keyword(s):  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Cycle Fatigue ◽  
Image Position

Abstract

Role of stress in the high cycle fatigue behavior of advanced 9Cr/CrMoV dissimilarly welded joint

2016 ◽  
Vol 31 (2) ◽  
pp. 292-301 ◽  
Author(s):  
Chendong Shao ◽  
Fenggui Lu ◽  
Zhuguo Li ◽  
Yan Cai ◽  
Peng Wang ◽  
...  
Keyword(s):  
High Cycle Fatigue ◽  
Welded Joint ◽  
Fatigue Behavior ◽  
Cycle Fatigue ◽  
Image Position

Abstract

High cycle fatigue behavior of different regions in a low-pressure sand-cast GW103K magnesium alloy component

2014 ◽  
Vol 29 (21) ◽  
pp. 2587-2595 ◽  
Author(s):  
Longkang Jiang ◽  
Wencai Liu ◽  
Yanlei Li ◽  
Guohua Wu ◽  
Wenjiang Ding
Keyword(s):  
Magnesium Alloy ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Low Pressure ◽  
Cycle Fatigue ◽  
Alloy Component ◽  
Sand Cast ◽  
Image Position

Abstract

scholarly journals Influence of warm caliber rolling on tensile response and high cycle fatigue behavior of hypereutectoid steel

2021 ◽  
Vol 10 ◽  
pp. 205-215
Author(s):  
Kyu-Sik Kim ◽  
Young-Kyun Kim ◽  
Hyeon-Jin Kim ◽  
Jeoung Han Kim ◽  
Kee-Ahn Lee
Keyword(s):  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Cycle Fatigue ◽  
Hypereutectoid Steel ◽  
Tensile Response

The Effect of HFPD Thermally Sprayed WC-Co Coatings on the Fatigue Behavior and Deformation of Al 2024-T4

2000 ◽  
Author(s):  
A. Ibrahim ◽  
C.C. Berndt
Keyword(s):  
High Frequency ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Cycle Fatigue ◽  
Pulse Detonation ◽  
Deformation Behaviors ◽  
Life Distributions ◽  
Thermally Sprayed ◽  
Al 2024 ◽  
Frequency Pulse

Abstract The effect of high frequency pulse detonation (HFPD) and HVOF thermally sprayed WC-Co coatings on the high cycle fatigue (HCF) behavior of 2024-T4 aluminum was investigated. The fatigue life distributions of specimens in the polished and coated conditions are presented as a function of the probability of failure. The monotonic and cyclic deformation behaviors of the as-received and as-coated specimens were investigated. The conclusions show that, (i) the HFPD sprayed specimens exhibited slightly higher fatigue lives compared to the uncoated specimens, (ii) the HVOF sprayed specimens exhibited significantly higher fatigue lives compared to the uncoated specimens, and (iii) the as-coated specimen was cyclically stable.

Effect of corrosion and sandblasting on the high cycle fatigue behavior of reinforcing B500C steel bars

2017 ◽  
Author(s):  
Marina C. Vasco ◽  
Panagiota Polydoropoulou ◽  
Apostolos N. Chamos ◽  
Spiros G. Pantelakis
Keyword(s):  
Mass Loss ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Salt Spray ◽  
Fatigue Tests ◽  
Tensile Behavior ◽  
Loading Frequency ◽  
Reinforcing Steel ◽  
Cycle Fatigue ◽  
Steel Bars

In a series of applications, steel reinforced concrete structures are subjected to fatigue loads during their service life, what in most cases happens in corrosive environments. Surface treatments have been proved to represent proper processes in order to improve both fatigue and corrosion resistances. In this work, the effect of corrosion and sandblasting on the high cycle fatigue behavior reinforcing steel bars is investigated. The investigated material is the reinforcing steel bar of technical class B500C, of nominal diameter of 12 mm. Steel bars specimens were first exposed to corrosion in alternate salt spray environment for 30 and 60 days and subjected to both tensile and fatigue tests. Then, a series of specimens were subjected to common sandblasting, corroded and mechanically tested. Metallographic investigation and corrosion damage evaluation regarding mass loss and martensitic area reduction were performed. Tensile tests were conducted after each corrosion exposure period prior to the fatigue tests. Fatigue tests were performed at a stress ratio, R, of 0.1 and loading frequency of 20 Hz. All fatigue tests series as well as tensile test were also performed for as received steel bars to obtain the reference behavior. The results have shown that sandblasting hardly affects the tensile behavior of the uncorroded material. The effect of sandblasting on the tensile behavior of pre-corroded specimens seems to be also limited. On the other hand, fatigue results indicate an improved fatigue behavior for the sandblasted material after 60 days of corrosion exposure. Martensitic area reductions, mass loss and depth of the pits were significantly smaller for the case of sandblasted materials, which confirms an increased corrosion resistance.

High-cycle fatigue tests of pretensioned concrete beams

PCI Journal ◽  
2022 ◽  
Vol 67 (1) ◽  
Author(s):  
Jörn Remitz ◽  
Martin Empelmann
Keyword(s):  
Fatigue Life ◽  
High Cycle Fatigue ◽  
Concrete Beams ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Design Methods ◽  
Test Results ◽  
Cycle Fatigue ◽  
Pretensioned Concrete ◽  
Current Design

Pretensioned concrete beams are widely used as bridge girders for simply supported bridges. Understanding the fatigue behavior of such beams is very important for design and construction to prevent fatigue failure. The fatigue behavior of pretensioned concrete beams is mainly influenced by the fatigue of the prestressing strands. The evaluation of previous test results from the literature indicated a reduced fatigue life in the long-life region compared with current design methods and specifications. Therefore, nine additional high-cycle fatigue tests were conducted on pretensioned concrete beams with strand stress ranges of about 100 MPa (14.5 ksi). The test results confirmed that current design methods and specifications overestimate the fatigue life of embedded strands in pretensioned concrete beams.

Sign in / Sign up

Export Citation Format

Share Document