Interfacial reactions of Sn–Cu and Sn–Pb–Ag solder with Au/Ni during extended time reflow in ball grid array packages

2004 ◽  
Vol 19 (10) ◽  
pp. 2897-2904 ◽  
Author(s):  
M.N. Islam ◽  
Y.C. Chan ◽  
A. Sharif
Keyword(s):  
Growth Rate ◽  
Shear Strength ◽  
Solder Joint ◽  
Intermetallic Compounds ◽  
Solder Joints ◽  
Interfacial Reactions ◽  
Extended Time ◽  
Reflow Time ◽  
Ternary Intermetallic Compounds ◽  
Ball Grid Array Packages

Lead-free solders with high Sn content cause excessive interfacial reactions at the interface with under-bump metallization during reflow. The interface formed after reflow affects the reliability of the solder joint. For this paper, we investigated the interfacial reactions of Sn0.7Cu and Sn36Pb2Ag solder on electrolytic Ni layer for different reflow times. The traditionally used Sn36Pb2Ag solder was used as a reference. It was found that during as-reflowed, the formation of Cu-rich Sn–Cu–Ni ternary intermetallic compounds (TIMCs) at the interface of Sn0.7Cu solder with electrolytic Ni is much quicker, resulting in the entrapment of some Pb (which is present as impurity in the Sn–Cu solder) rich phase in the TIMCs. During extended time of reflow, high (>30 at.%), medium (30-15 at.%) and low (<15 at.%) Cu TIMCs formed at the interface. The amount of Cu determined the growth rate of TIMCs. Cu-rich TIMCs had higher growth rate and consumed more Ni layer. By contrast, the growth rate of the Ni–Sn binary intermetallic compounds (BIMCs) in the Sn36Pb2Ag solder joint was slower, and the Ni–Sn BIMC was more stable and adherent. The dissolution rate of electrolytic Ni layer for Sn0.7Cu solder joint was higher than the Sn36Pb2Ag solder joints. Less than 3 μm of the electrolytic Ni layer was consumed during molten reaction by the higher Sn containing Sn0.7Cu solder in 180 min at 250 °C. The shear strength of Sn–Pb–Ag solder joints decreased within 30 min of reflow time from 1.938 to 1.579 kgf due to rapid formation of ternary Ni–Sn–Au compounds on the Ni–Sn BIMCs. The shear strength of Sn0.7Cu solder joint is relatively stable from 1.982 to 1.861 kgf during extended time reflow. Cu prevents the resettlement of Au at the interface. The shear strength does not depend on the thickness of intermetallic compounds (IMCs) and reflow time. Ni/Sn–Cu solder system has higher strength and can be used during prolonged reflow.

Effects of Bismuth Content on the Microstructure, Shear Strength and Thermal Properties of Sn-0.7Cu-0.05Ni Solder Joints

2020 ◽  
Vol 982 ◽  
pp. 115-120
Author(s):  
Phairote Sungkhaphaitoon ◽  
Tanyaporn Suwansukho
Keyword(s):  
Shear Strength ◽  
Thermal Properties ◽  
Solder Joint ◽  
Intermetallic Compounds ◽  
Interfacial Layer ◽  
Solder Joints ◽  
Peak Temperature ◽  
Cu Substrate ◽  
Bismuth Content ◽  
Pasty Range

The effects of bismuth content on the microstructure, shear strength and thermal properties of Sn-0.7Cu-0.05Ni solder joints were investigated. Adding 2 wt% elemental Bi to Sn-0.7Cu-0.05Ni solder joints reduced peak temperature by about 6.7 °C, increased pasty range by 4.2 °C and raised undercooling by 3.1 °C. The microstructure of the interfacial layer between solder and Cu substrate was composed of (Cu,Ni)6Sn5 and (Cu,Ni)3Sn intermetallic compounds (IMCs). The solder joint included a phase of SnBi and Cu6Sn5 IMCs. The addition of elemental Bi increased shear strength and suppressed the growth of IMCs in the interfacial layer of the solder joints.

Microstructure Evolution of Sn-2.5Ag-2.0Ni Solder Joint with Various Ni Platings on SiCp/Al Composites

2010 ◽  
Vol 638-642 ◽  
pp. 3811-3818
Author(s):  
Mao Wu ◽  
Xin Bo He ◽  
Shu Bin Ren ◽  
Ming Li Qin ◽  
Xuan Hui Qu
Keyword(s):  
Growth Rate ◽  
Shear Strength ◽  
Intermetallic Compound ◽  
Solder Joint ◽  
Aging Time ◽  
Microstructure Evolution ◽  
Thermal Stresses ◽  
Solder Joints ◽  
Electroless Ni

A novel Sn-2.5Ag-2.0Ni alloy has been developed for soldering of SiCp/Al composites substrate with various types of Ni coatings. An investigation about electroplated Ni layer, electroless Ni-5 wt.% P, Ni-10wt.% P and Ni-B layers has been carried out. It is found that the solder joints possess a single intermetallic compound (IMC) Ni3Sn4, which coarsens with an increase in aging time. The formation of Ni2SnP has been observed to significantly affect the reliability of the solder joints. But the formation of Ni2SnP can be suppressed by lowering the P contents in as-deposited Ni coatings. It has been also found that the thermal stresses generated in solder joint increases with the decrease of P contents in Ni-P layer. Furthermore, the concentration of thermal stresses in the electroplated Ni solder joint is found to be higher than that in other three electroless Ni layers. Out of four as-deposited Ni coatings, the Ni-B layer exhibits good wettability with solder and low IMC growth rate during aging. Also, the shear strength of solder joint decreases with an increase in aging time and Ni-B solder joint demonstrates the highest shear strength after long term aging.

Effect of intermetallic compound layer thickness on the shear strength of 1206 chip resistor solder joint

2015 ◽  
Vol 27 (1) ◽  
pp. 52-58 ◽  
Author(s):  
Peter K. Bernasko ◽  
Sabuj Mallik ◽  
G. Takyi
Keyword(s):  
Shear Strength ◽  
Intermetallic Compound ◽  
Solder Joint ◽  
Layer Thickness ◽  
Solder Joints ◽  
Ageing Time ◽  
Circuit Board ◽  
Intermetallic Compound Layer ◽  
Content Type ◽  
Surface Mount

Purpose – The purpose of this paper is to study the effect of intermetallic compound (IMC) layer thickness on the shear strength of surface-mount component 1206 chip resistor solder joints. Design/methodology/approach – To evaluate the shear strength and IMC thickness of the 1206 chip resistor solder joints, the test vehicles were conventionally reflowed for 480 seconds at a peak temperature of 240°C at different isothermal ageing times of 100, 200 and 300 hours. A cross-sectional study was conducted on the reflowed and aged 1206 chip resistor solder joints. The shear strength of the solder joints aged at 100, 200 and 300 hours was measured using a shear tester (Dage-4000PXY bond tester). Findings – It was found that the growth of IMC layer thickness increases as the ageing time increases at a constant temperature of 175°C, which resulted in a reduction of solder joint strength due to its brittle nature. It was also found that the shear strength of the reflowed 1206 chip resistor solder joint was higher than the aged joints. Moreover, it was revealed that the shear strength of the 1206 resistor solder joints aged at 100, 200 and 300 hours was influenced by the ageing reaction times. The results also indicate that an increase in ageing time and temperature does not have much influence on the formation and growth of Kirkendall voids. Research limitations/implications – A proper correlation between shear strength and fracture mode is required. Practical implications – The IMC thickness can be used to predict the shear strength of the component/printed circuit board pad solder joint. Originality/value – The shear strength of the 1206 chip resistor solder joint is a function of ageing time and temperature (°C). Therefore, it is vital to consider the shear strength of the surface-mount chip component in high-temperature electronics.

scholarly journals Shear Strength and Aging Characteristics of Sn-3.0Ag-0.5Cu/Cu Solder Joint Reinforced with ZrO2 Nanoparticles

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1295
Author(s):  
Sri Harini Rajendran ◽  
Seung Jun Hwang ◽  
Jae Pil Jung
Keyword(s):  
Shear Strength ◽  
Solder Joint ◽  
Solder Joints ◽  
Solder Matrix ◽  
Fracture Analysis ◽  
Zro2 Nanoparticles ◽  
Solder Paste ◽  
Lap Shear ◽  
Matrix Fracture ◽  
The Matrix

This study investigates the shear strength and aging characteristics of Sn-3.0Ag-0.5Cu (SAC 305)/Cu joints by the addition of ZrO2 nanoparticles (NPs) having two different particle size: 5–15 nm (ZrO2A) and 70–90 nm (ZrO2B). Nanocomposite pastes were fabricated by mechanically mixing ZrO2 NPs and the solder paste. ZrO2 NPs decreased the β-Sn grain size and Ag3Sn intermetallic compound (IMC) in the matrix and reduced the Cu6Sn5 IMC thickness at the interface of lap shear SAC 305/Cu joints. The effect is pronounced for ZrO2A NPs added solder joint. The solder joints were isothermally aged at 175 °C for 24, 48, 144 and 256 h. NPs decreased the diffusion coefficient from 1.74 × 10–16 m/s to 3.83 × 10–17 m/s and 4.99 × 10–17 m/s for ZrO2A and ZrO2B NPs added SAC 305/Cu joints respectively. The shear strength of the solder joints decreased with the aging time due to an increase in the thickness of interfacial IMC and coarsening of Ag3Sn in the solder. However, higher shear strength exhibited by SAC 305-ZrO2A/Cu joints was attributed to the fine Ag3Sn IMC’s dispersed in the solder matrix. Fracture analysis of SAC 305-ZrO2A/Cu joints displayed mixed solder/IMC mode upon 256 h of aging.

Effects of electromigration on the growth of intermetallic compounds in Cu/SnBi/Cu solder joints

2008 ◽  
Vol 23 (10) ◽  
pp. 2591-2596 ◽  
Author(s):  
X. Gu ◽  
D. Yang ◽  
Y.C. Chan ◽  
B.Y. Wu
Keyword(s):  
Activation Energy ◽  
Solder Joint ◽  
Intermetallic Compounds ◽  
Direct Current ◽  
Solder Joints ◽  
Cathode Side ◽  
Anode Side ◽  
Kinetics Parameters ◽  
Ambient Temperatures ◽  
Current Stressing

In this study, the effects of electromigration (EM) on the growth of Cu–Sn intermetallic compounds (IMCs) in Cu/SnBi/Cu solder joints under 5 × 103 A/cm2 direct current stressing at 308, 328, and 348 K were investigated. For each Cu/SnBi/Cu solder joint under current stressing, the IMCs at the cathode side grew faster than that at the anode side. The growth of these IMCs at the anode side and the cathode side were enhanced by electric current. The growth of these IMCs at the cathode followed a parabolic growth law. The kinetics parameters of the growth of the IMCs were calculated from the thickness data of the IMCs at the cathode side at different ambient temperatures. The calculated intrinsic diffusivity (D0) of the Cu–Sn IMCs was 9.91 × 10−5 m2/s, and the activation energy of the growth of the total Cu–Sn IMC layer was 89.2 kJ/mol (0.92 eV).

Formation and Evolution of Intermetallic Compounds in Solder Joint for Electronic Interconnect

2011 ◽  
Vol 687 ◽  
pp. 80-84
Author(s):  
Chang Hua Du ◽  
Hai Jian Zhao ◽  
Li Meng Yin ◽  
Fang Chen
Keyword(s):  
Mechanical Properties ◽  
Solder Joint ◽  
Intermetallic Compounds ◽  
Isothermal Aging ◽  
Solder Joints ◽  
Growth Behavior ◽  
Electronic Products ◽  
Formation And Evolution ◽  
Kirkendall Voids ◽  
Reliability Of Solder Joints

As solder joints become increasingly miniaturized to meet the severe demands of future electronic packaging, the thickness of intermetallic compounds (IMC) in solder joint continuously decreases, while, the IMC proportion to the whole solder joint increases. So IMC plays a more and more important role in the reliability of microelectronic structure and microsystems. In this paper, the formation and growth behavior, along with the composition of IMC at the interface of Sn-based solders/Cu substrate in soldering were reviewed comprehensively. The effect of isothermal aging, thermal-shearing cycling and electromigration on the interfacial IMC growth and evolution were also presented. Furthermore, the formation mechanism of Kirkendall voids during thermal aging was introduced. In addition, the effect of the interfacial IMC on mechanical properties of solder joints was in-depth summarized. Adopting an appropriate flux to control the thickness of the IMC to improve the reliability of solder joints and electronic products was proposed in the end of this paper.

Effect of Sb Addition on Microstructure and Shear Strength of Sn-Ag Solder Joints

2004 ◽  
Vol 261-263 ◽  
pp. 501-506 ◽  
Author(s):  
H.T. Lee ◽  
C.L. Yang ◽  
Ming He Chen ◽  
C.S. Li
Keyword(s):  
Mechanical Properties ◽  
Growth Rate ◽  
Shear Strength ◽  
Intermetallic Compound ◽  
Solder Joints ◽  
Thermal Storage ◽  
Experimental Results ◽  
Storage Test ◽  
Ag3sn Phase ◽  
Epma Analysis

The effect of Sb addition on microstructure, intermetallic compound (IMC) and mechanical properties of Sn-Ag solder joints is investigated. The compositions of selected solders are Sn2.58Ag, Sn2.82Ag1.75Sb, Sn2.87Ag4.75Sb and Sn2.7Ag8.78Sb. Experimental results show that most of the added Sb are solved in -Sn matrix, and the rest react with the Ag3Sn to form Ag3(Sb,Sn) phase, which contributes to suppress the coarsening of Ag3Sn phase. SbSn phase can be observed in β-Sn matrix as the Sb addition exceeds 4.75% and remains stable during the thermal storage test. The solder microhardness increases with increasing Sb. And the growth rate of interfacial IMC layer decreases as Sb addition increases. EPMA analysis indicates there are some Sb diffusing into the interfacial IMC layer. Shear strength of solder joints are raised by adding Sb. The shear strength by as-soldered condition are 27.8MPa (0%Sb), 29MPa (1.75%Sb), 30.4MPa (4.75%Sb) and 43.4MPa (8.78%Sb) respectively

Property of Sn-37Pb solder bumps with different diameter during thermal shock

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Guisheng Gan ◽  
Donghua Yang ◽  
Yi-ping Wu ◽  
Xin Liu ◽  
Pengfei Sun ◽  
...  
Keyword(s):  
Shear Strength ◽  
Solder Joint ◽  
Thermal Shock ◽  
Solder Joints ◽  
Test Method ◽  
Content Type ◽  
Ball Size ◽  
Solder Bumps ◽  
Free Solder ◽  
The Impact

Purpose The impact strength of solder joint under high strain rate was evaluated by board level test method. However, the impact shear test of single solder bump was more convenient and economical than the board level test method. With the miniaturization of solder joints, solder joints were more prone to failure under thermal shock and more attention has been paid to the impact reliability of solder joint. But Pb-free solder joints may be paid too much attention and Sn-Pb solder joints may be ignored. Design/methodology/approach In this study, thermal shock test between −55°C and 125°C was conducted on Sn-37Pb solder bumps in the BGA package to investigate microstructural evolution and growth mechanism of interfacial intermetallic compounds (IMCs) layer. The effects of thermal shock and ball diameter on the mechanical property and fracture behavior of Sn-37Pb solder bumps were discussed. Findings With the increase of ball size, the same change tendency of shear strength with thermal shock cycles. The shear strength of the solder bumps was the highest after reflow; with the increase of the number of thermal shocks, the shear strength of the solder bumps was decreased. But at the time of 2,000 cycles, the shear strength was increased to the initial strength. Minimum shear strength almost took place at 1,500 cycles in all solder bumps. The differences between maximum shear strength and minimum shear strength were 9.11 MPa and 16.83 MPa, 17.07 MPa and 15.59 MPa in φ0.3 mm and φ0.4 mm, φ0.5 mm and φ0.6 mm, respectively, differences were increased with increasing of ball size. With similar reflow profile, the thickness of IMC decreased as the diameter of the ball increased. The thickness of IMC was 2.42 µm and 2.17 µm, 1.63 µm and 1.77 µm with increasing of the ball size, respectively. Originality/value Pb-free solder was gradually used to replace traditional Sn-Pb solder and has been widely used in industry. Nevertheless, some products inevitably used a mixture of Sn-Pb and Pb-free solder to make the transition from Sn-Pb to Pb-free solder. Therefore, it was very important to understand the reliability of Sn-Pb solder joint and more further research works were also needed.

Effects of Sn-Ag-x leveling layers on the microstructure and mechanical properties of SnBi low-temperature solder joints

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yang Liu ◽  
Yuxiong Xue ◽  
Min Zhou ◽  
Rongxing Cao ◽  
Xianghua Zeng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Low Temperature ◽  
Solder Joint ◽  
Design Methodology ◽  
Solder Joints ◽  
Fracture Morphology ◽  
Content Type ◽  
Before And After ◽  
Mechanical Performances

Purpose The purpose of this paper is to investigate the effects of Sn-Ag-x leveling layers on the mechanical properties of SnBi solder joints. Four Sn-Ag-x (Sn-3.0Ag-0.5Cu, Sn-0.3Ag-0.7Cu, Sn-0.3Ag-0.7Cu-0.5 Bi-0.05Ni and Sn-3.0Ag-3.0 Bi-3.0In) leveling layers were coated on Cu pads to prepare SnBi/Sn-Ag-x/Cu solder joints. The microstructure, hardness, shear strength and fracture morphology of solder joints before and after aging were studied. Design/methodology/approach The interfacial brittleness of the SnBi low-temperature solder joint is a key problem affecting its reliability. The purpose of this study is to improve the mechanical properties of the SnBi solder joint. Findings Owing to the addition of the leveling layers, the grain size of the ß-Sn phase in the SnBi/Sn-Ag-x/Cu solder joint is significantly larger than that in the SnBi/Cu eutectic solder joint. Meanwhile, the hardness of the solder bulk in the SnBi/Cu solder joint shows a decrease trend because of the addition of the leveling layers. The SnBi/Cu solder joint shows obvious strength drop and interfacial brittle fracture after aging. Through the addition of the Sn-Ag-x layers, the brittle failure caused by aging is effectively suppressed. In addition, the Sn-Ag-x leveling layers improve the shear strength of the SnBi/Cu solder joint after aging. Among them, the SnBi/SACBN/Cu solder joint shows the highest shear strength. Originality/value This work suppresses the interfacial brittleness of the SnBi/Cu solder joint after isothermal aging by adding Sn-Ag-x leveling layers on the Cu pads. It provides a way to improve the mechanical performances of the SnBi solder joint.

Sign in / Sign up

Export Citation Format

Share Document