Synthesis and Properties of Lead Zirconate Titanate Thin Films Via Metalorganic Chemical Vapor Deposition

2002 ◽  
Vol 17 (6) ◽  
pp. 1536-1542 ◽  
Author(s):  
Chih-Yi Pan ◽  
Yin-Lang Chen ◽  
Dah-Shyang Tsai
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Activation Energy ◽  
Temperature Dependence ◽  
Lead Zirconate Titanate ◽  
Surface Reaction ◽  
Lead Zirconate ◽  
Strong Temperature Dependence ◽  
Phase Reaction ◽  
Zirconate Titanate

Ferroelectric PZT thin films were deposited on Pt and SrRuO3 substrates in a cold-wall reactor, using the Pb(C2H5)4/Zr(OBu)4/Ti(OPri)4/O2 reaction system. In comparison with Pt substrate, the growth rate of lead zirconate titanate (PZT) thin film was higher on SrRuO3. Lead content of the thin film deposited on either substrate at low temperatures (723–863 K) was much more temperature dependent than the other two metal contents. The strong temperature dependence originated from the high activation energy in the initial decomposition of Pb(C2H5)4 vapor, which was 54 kcal/mol. The surface reaction constant of lead precursor had much lower temperature dependence. The activation energy of surface reaction for PbO, estimated from deposition in a mini-chamber, was 6 kcal/mol on Pt and 9 kcal/mol on the SrRuO3 substrate. Therefore, the incorporation path of component oxide PbO, whose apparent activation energy was 31 kcal/mol on Pt and 29 kcal/mol on SrRuO3, essentially involved considerable gas-phase reaction. The PZT (50/50) thin film on SrRuO3 bottom electrode possessed a lower coercive field and a smaller remnant polarization than that on Pt. The PZT capacitor on SrRuO3 was also less vulnerable to polarization fatigue.

Preparation of Lead Zirconate Titanate Thin Film Using Magnetron Sputtering

2012 ◽  
Vol 538-541 ◽  
pp. 162-165
Author(s):  
Li Yang Yu ◽  
Yang Wang ◽  
Guo Hua Yao
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Magnetron Sputtering ◽  
Lead Zirconate Titanate ◽  
Energy Dispersive Spectrometer ◽  
Lead Zirconate ◽  
Gas Content ◽  
Crystalline Quality ◽  
Oxide Content ◽  
Zirconate Titanate

PZT(lead zirconate titanate) piezoelectric thin films were deposited on the glass substrates by RF (radio frequency) magnetron sputtering reaction method. The XRD(X-ray diffraction) analysis is used to characterize the structure of thin film, the pattern of EDS(energy dispersive spectrometer) shows the composition of thin film, and SEM(Scanning Electron Microscopy) is used to study the morphologies of thin films. The influence of different sputter gas content on the crystalline quality and the surface morphology are also investigated. The results demonstrate that volatile of lead oxide is closed to the ratio with the oxide content. The roughness of the thin film is influenced by the crystalline quality.

Measurements of Piezoelectric Coefficient d33 of Lead Zirconate Titanate Thin Films Using a Mini Force Hammer

2013 ◽  
Vol 135 (1) ◽  
Author(s):  
Qing Guo ◽  
G. Z. Cao ◽  
I. Y. Shen
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Coefficient ◽  
Lead Zirconate ◽  
New Method ◽  
Impulsive Force ◽  
Pzt Thin Films ◽  
Zirconate Titanate ◽  
Pzt Thin Film

Lead zirconate titanate (PbZrxTi1-xO3, or PZT) is a piezoelectric material widely used as sensors and actuators. For microactuators, PZT often appears in the form of thin films to maintain proper aspect ratios. One major challenge encountered is accurate measurement of piezoelectric coefficients of PZT thin films. In this paper, we present a simple, low-cost, and effective method to measure piezoelectric coefficient d33 of PZT thin films through use of basic principles in mechanics of vibration. A small impact hammer with a tiny tip acts perpendicularly to the PZT thin-film surface to generate an impulsive force. In the meantime, a load cell at the hammer tip measures the impulsive force and a charge amplifier measures the responding charge of the PZT thin film. Then the piezoelectric coefficient d33 is obtained from the measured force and charge based on piezoelectricity and a finite element modeling. We also conduct a thorough parametric study to understand the sensitivity of this method on various parameters, such as substrate material, boundary conditions, specimen size, specimen thickness, thickness ratio, and PZT thin-film material. Two rounds of experiments are conducted to demonstrate the feasibility and accuracy of this new method. The first experiment is to measure d33 of a PZT disk resonator whose d33 is known. Experimental results show that d33 measured via this method is as accurate as that from the manufacturer's specifications within its tolerance. The second experiment is to measure d33 of PZT thin films deposited on silicon substrates. With the measured d33, we predict the displacement of PZT thin-film membrane microactuators. In the meantime, the actuator displacement is measured via a laser Doppler vibrometer. The predicted and measured displacements agree very well validating the accuracy of this new method.

Improvement of Ferroelectric Properties of Lead Zirconate Titanate Thin Films by Ion-substitution using Rare-earth Cations

2004 ◽  
Vol 830 ◽  
Author(s):  
Hiroshi Nakaki ◽  
Hiroshi Uchida ◽  
Shoji Okamoto ◽  
Shintaro Yokoyama ◽  
Hiroshi Funakubo ◽  
...  
Keyword(s):  
Thin Films ◽  
Rare Earth ◽  
Lead Zirconate Titanate ◽  
Ferroelectric Property ◽  
Ferroelectric Properties ◽  
Lead Zirconate ◽  
Crystal Anisotropy ◽  
Pzt Film ◽  
Zirconate Titanate ◽  
Ion Substitution

ABSTRACTRare-earth-substituted tetragonal lead zirconate titanate thin films were synthesized for improving the ferroelectric property of conventional lead zirconate titanate. Thin films of Pb1.00REx (Zr0.40Ti0.60)1-(3x /4)O3 (x = 0.02, RE = Y, Dy, Er and Yb) were deposited on (111)Pt/Ti/SiO2/(100)Si substrates by a chemical solution deposition (CSD). B-site substitution using rare-earth cations described above enhanced the crystal anisotropy, i.e., ratio of PZT lattice parameters c/a. Remanent polarization (Pr) of PZT film was enhanced by Y3+-, Dy3+- and Er3+-substitution from 20 μC/cm2 up to 26, 25 and 26 μC/cm2 respectively, while ion substitution using Yb3+ degraded the Pr value down to 16 μC/cm2. These films had similar coercive fields (Ec) of around 100 kV/cm. Improving the ferroelectric property of PZT film by rare-earth-substitution would be ascribed to the enhancement of the crystal anisotropy. We concluded that ion substitution using some rare-earth cations, such as Y3+, Dy3+ or Er3+, is one of promising technique for improving the ferroelectric property of PZT film.

Early Stages of Crystallization of Sol−Gel-Derived Lead Zirconate Titanate Thin Films

2003 ◽  
Vol 15 (5) ◽  
pp. 1147-1155 ◽  
Author(s):  
A. Wu ◽  
P. M. Vilarinho ◽  
I. Reaney ◽  
I. M. Miranda Salvado
Keyword(s):  
Thin Films ◽  
Lead Zirconate Titanate ◽  
Sol Gel ◽  
Lead Zirconate ◽  
Early Stages ◽  
Zirconate Titanate

Energy Dissipation Mechanisms in Lead Zirconate Titanate Thin Film Transduced Micro Cantilevers

2006 ◽  
Vol 45 (11) ◽  
pp. 8795-8800 ◽  
Author(s):  
Jian Lu ◽  
Tsuyoshi Ikehara ◽  
Yi Zhang ◽  
Ryutaro Maeda ◽  
Takashi Mihara
Keyword(s):  
Thin Film ◽  
Energy Dissipation ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
Zirconate Titanate ◽  
Titanate Thin Film
Sign in / Sign up

Export Citation Format

Share Document