Effects of solution temperature on mechanical properties of 319.0 aluminum casting alloys containing trace beryllium

2000 ◽  
Vol 15 (9) ◽  
pp. 2027-2035 ◽  
Author(s):  
Paih-Shiarng Wang ◽  
Sheng-Long Lee ◽  
Jing-Chie Lin ◽  
Min-Ten Jahn
Keyword(s):  
Mechanical Properties ◽  
Void Nucleation ◽  
Average Length ◽  
Solution Treatment ◽  
Fracture Initiation ◽  
Solution Temperature ◽  
Chinese Script ◽  
Eutectic Melting ◽  
Iron Intermetallics ◽  
Silicon Particles

The effects of beryllium (Be) and solution temperature on the morphologies of iron intermetallics, silicon particles, and copper intermetallics, relative to the mechanical properties of 319.0 alloys, were investigated. The experimental results indicated that adding Be to the alloy can raise the Al–Al2Cu eutectic melting temperature, change some plateletlike shape (βndash;Al5FeSi) of iron intermetallics to comparatively harmless Chinese-script morphologies (α–Al8Fe2Si), and reduce the amount and average length of βndash;Al5FeSi platelets. During high-temperature solution treatment (>500 °C), the thinner and smaller the β–Al5FeSi platelets were, the faster they dissolved and fragmented. However, where the solution temperature exceeded the Al–Al2Cu eutectic melting point, the Al–Al2Cu eutectic melted and resulted in an ultrafine eutectic phase on quenching, which deteriorated mechanical properties. The fracture behavior of 319 alloy was affected by the morphologies of the iron intermetallics, silicon particles, and copper intermetallics. Fractographic analysis of tested compact tension specimens revealed that the fracture processes were mainly initiated by void nucleation at β–Al5FeSi platelets as a result of their cracking and decohesion from the matrix. Adding Be to the 319.0 alloy and optimizing the solution temperature could significantly decrease the number of fracture-initiation sites of β–Al5FeSi platelets and improve the tensile properties and fracture toughness.

scholarly journals The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3798
Author(s):  
Meng Sun ◽  
Dong Li ◽  
Yanhua Guo ◽  
Ying Wang ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Time ◽  
Volume Fraction ◽  
Low Cost ◽  
Solution Treatment ◽  
Solution Temperature ◽  
The Novel ◽  
Α Phase ◽  
The Cost

In order to reduce the cost of titanium alloys, a novel low-cost Ti-3Al-5Mo-4Cr-2Zr-1Fe (Ti-35421) titanium alloy was developed. The influence of heat treatment on the microstructure characteristics and mechanical properties of the new alloy was investigated. The results showed that the microstructure of Ti-35421 alloy consists of a lamina primary α phase and a β phase after the solution treatment at the α + β region. After aging treatment, the secondary α phase precipitates in the β matrix. The precipitation of the secondary α phase is closely related to heat treatment parameters—the volume fraction and size of the secondary α phase increase when increasing the solution temperature or aging time. At the same solution temperature and aging time, the secondary α phase became coarser, and the fraction decreased with increasing aging temperature. When Ti-35421 alloy was solution-treated at the α + β region for 1 h with aging surpassing 8 h, the tensile strength, yield strength, elongation and reduction of the area were achieved in a range of 1172.7–1459.0 MPa, 1135.1–1355.5 MPa, 5.2–11.8%, and 7.5–32.5%, respectively. The novel low-cost Ti-35421 alloy maintains mechanical properties and reduces the cost of materials compared with Ti-3Al-5Mo-5V-4Cr-2Zr (Ti-B19) alloy.

Effect of Solution Temperature on the Microstructure and Mechanical Properties of Wrought 316LN Stainless Steel

2014 ◽  
Vol 915-916 ◽  
pp. 576-582 ◽  
Author(s):  
H. C. Wu ◽  
B. Yang ◽  
Ming Xian Zhang ◽  
Sheng Long Wang ◽  
Y. Z. Shi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stainless Steel ◽  
Solution Treatment ◽  
Solution Temperature ◽  
Tensile Fracture ◽  
316Ln Stainless Steel ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size ◽  
Fracture Morphologies

The effect of forging and solution temperature on the microstructure and mechanical properties of 316LN stainless steel has been investigated by optical microscope, tensile testing machine and scanning electron microscope (SEM). The results show that the average grain size of the steel was refined from 150μm to 70μm after forging and solution treatment. With increasing solution temperature, the tensile strength and yield strength decreased. On the contrary, the elongation of the steel increased with increasing solution temperature except at 1200°C. The tensile strength of the samples forged at 1100°C is better than those of the samples forged at 1000 and 1200°Cafter solution treatment. Tensile fracture morphologies observation showed that all the specimens have ductile fracture morphologies. With increasing solution temperature, the toughness of the steel becomes better and better except at 1200°C. Both the microstructure and mechanical properties of the 316LN stainless steel have been improved after forging at 1100°C and following by solution treatment at 1150°C.

Research on Mechanical Properties of High Boron Alloyed Stainless Steel Composite Plate Containing Titanium

2013 ◽  
Vol 401-403 ◽  
pp. 804-808
Author(s):  
Lin Lin Yuan ◽  
Jing Tao Han ◽  
Jing Liu ◽  
Yan Long Liu
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Composite Plate ◽  
Solution Treatment ◽  
Composite Plates ◽  
Solution Temperature ◽  
Forming Process ◽  
High Boron ◽  
Steel Composite ◽  
Ti Content

High boron alloyed stainless steel composite plates with different Ti content by cladding casting and hot forming process were fabricated. The mechanical properties of composite plates were analyzed after solution treatment. The results show that the composite plate has optimal microstructure and properties at 1100°C solution temperature, holding for 4h.The comprehensive properties of the composite plates are improved with the increase of Ti content, but excess Ti content can lower the plasticity. The elongation and the tensile strength of composite plate reaches 29% and 527MPa respectively, the mechanical properties can meet and exceed the supply standard requirements in ASTM A887-89 of U.S. when the reasonable content of Titanium is about 5%.

Effect of Solution Treatment on Microstructures and Mechanical Properties of Centrifugal Casting Al-Cu Alloy

2011 ◽  
Vol 306-307 ◽  
pp. 548-552
Author(s):  
Jun Li ◽  
Yan Wei Sui ◽  
Ai Hui Liu ◽  
Xin Zhao ◽  
Zhi Sun
Keyword(s):  
Mechanical Properties ◽  
Centrifugal Casting ◽  
Solution Treatment ◽  
Solution Time ◽  
Solution Temperature ◽  
Micro Hardness ◽  
Hardness Tester ◽  
Alloy Casting ◽  
Cu Alloy ◽  
Microstructures And Mechanical Properties

Al-Cu alloy castings are obtained in the vertical centrifugal field. The effects of solution treatment on the microstructures and mechanical properties of Al-Cu alloy casting were studied by OM, micro hardness tester and room temperature tension and compression test. The results show that, the strength, micro hardness and elongation percentage of Al-Cu alloy casting increase firstly and then decrease as the solution temperature increases, and the mechanical properties reach the maximum values as the solution temperature increases to 530°C. As solution time increasing, the mechanical properties of Al-Cu alloy casting increase firstly and then decrease. When the solution time is up to 6 hours, the mechanical properties reach maximum value.

scholarly journals Optimization of a Solution Treatment in the Al-Cu-Mg-Ag Alloy via a Microstructural Investigation

Metals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 66
Author(s):  
Hyeongsub So ◽  
Jae-Hong Shin ◽  
Leeseung Kang ◽  
Chanuk Jeong ◽  
Kyou-Hyun Kim
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Grain Growth ◽  
Microstructural Evolution ◽  
Precipitation Hardening ◽  
Solution Treatment ◽  
Solution Temperature ◽  
Al Alloy ◽  
Microstructural Investigation ◽  
Large Particles

We investigated the effect of solution temperature (Tsol. = 440–530 °C) on the mechanical properties of the Al–3.4Cu–0.34Mg–0.3Mn–0.17Ag alloy, finding that the investigated Al alloy showed the highest mechanical strength of σUTS = ~329 MPa at a Tsol. value of 470 °C. The microstructural investigation demonstrates that the mechanical properties for different Tsol. values stem from grain growth, precipitation hardening, and the formation of large particles at the grain boundaries. On the basis of Tsol. = 470 °C, the effect of each microstructural evolution is significantly different on the mechanical properties. In this study, the relationships between the microstructural evolution and the mechanical properties were investigated with respect to different values of Tsol.

scholarly journals Selection of optimal solution heat treatment of the casting cylinder heads

2018 ◽  
Vol 157 ◽  
pp. 02053 ◽  
Author(s):  
Eva Tillová ◽  
Mária Chalupová ◽  
Lenka Kuchariková ◽  
Juraj Belan ◽  
Denisa Závodská
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solution Heat Treatment ◽  
Treatment Time ◽  
Crack Nucleation ◽  
Particle Density ◽  
Solution Treatment ◽  
Optimal Solution ◽  
Solution Temperature ◽  
Selection Of

The effect of solution treatment on mechanical properties (UTS, elongation, Brinell hardness) and microstructure (Si-morphology and Si-size) of an aluminium alloy (A356) used for casting cylinder heads was studied. The tests were carried out with specimens machined from the bulkheads of V8 engine blocks cast by the low pressure process. The samples were tested in as-cast and T6 heat treating conditions (solution heat treatment at 530°C with different time - 2, 3, 4, 5, 6, 7 hours, quenching in water at 20°C and precipitation hardened for 4 hour at 160°C). The results show that used heat treatment improves mechanical properties of the cylinder head casts. Tensile strength and hardness of specimens increase with solution treatment time. The hardness is a reflection of solution strengthening and silicon particle distribution in matrix. Solution temperature 530°C and 5 hours solution time is appropriate to obtain better morphology and distribution of Si particles in microstructure. Prolonged solution treatment (more than 5 hours) leads to a coarsening of the Si particles, while the numerical Si density decreases. As the particle density decreases, a fewer number of sites are available for crack nucleation, and hence, the fracture properties are improved. The data obtained from this study will be used to improve process control, and to help the selection of heat treatment of the casting for future products.

Effect of Solution Treatment on Microstructure and Mechanical Properties of Hot-Extruded Cu-15Ni-8Sn Alloy

2017 ◽  
Vol 898 ◽  
pp. 1156-1162
Author(s):  
Xun Wang ◽  
Chao Zhao ◽  
Yan Gen Yu ◽  
Zong Qiang Luo ◽  
Wei Wen Zhang
Keyword(s):  
Mechanical Properties ◽  
Volume Fraction ◽  
Solution Treatment ◽  
Optical Microscope ◽  
Solution Time ◽  
Solution Temperature ◽  
Scanning Calorimetry ◽  
Annealing Twins ◽  
Optimum Solution ◽  
Electronic Microscope

The effects of solution treatment on the microstructure evolution of hot-extruded Cu-15Ni-8Sn alloy were investigated by optical microscope (OM), scanning electronic microscope (SEM), differential scanning calorimetry (DSC) and tensile testing, and the effects of solution temperature and time on the mechanical properties of the alloys were analyzed. The results indicated that, the γ-phases precipitated at first and then dissolved with the extension of the solution time during solutionizing at 800 C,the volume fraction of theγ-phase reached its peak at about 1h. However when solutionizing at 860°C, theγ-phase solely dissolved gradually with the extension of the solution time . In addition, a small amount of annealing twins appeared intragranular in the process of solution treatment. The γ-phase dissolution and the grain growth of α (Cu) were the main softening factors of the alloy during the solution treatment. Through overall consideration, the optimum solution treatment was annealing at 840°Cfor 1 h.

Effect of Squeeze Casting and Solution Treatment on the Microstructure and Properties of ZA27 Worm Wheel

2015 ◽  
Vol 817 ◽  
pp. 63-70
Author(s):  
Quan Li Zhu ◽  
Zi Yong Wu ◽  
Jia Jian Chen
Keyword(s):  
Mechanical Properties ◽  
Friction And Wear ◽  
Squeeze Casting ◽  
Solution Treatment ◽  
Shrinkage Porosity ◽  
Solution Temperature ◽  
Permanent Mold ◽  
Za27 Alloy ◽  
Mold Casting ◽  
Ε Phase

Compared with permanent mold casting, the microstructure, mechanical properties, friction and wear of squeeze casting ZA27 alloy were studied. The results showed that squeeze casting can reduce or eliminate shrinkage porosity defect, refine or improve the microstructure and the shape and distribution of copper-rich ε phase which leads to the obvious improvement of the performance. In addition, with the increase of solution temperature, higher degree of super-saturation can enhance the tensile strength and hardness of ZA27 alloy. The better deformation coordination is an important factor to the enhancement of elongation. Remelting among grain boundaries leads to the deterioration of performance rapidly.

Microstructures and Mechanical Properties of an Al-Cu-Li-Mg-Zr Alloy Containing Zn and Mn

2007 ◽  
Vol 546-549 ◽  
pp. 995-1002 ◽  
Author(s):  
Yong Lai Chen ◽  
Jin Feng Li ◽  
Yu Wei Zhang ◽  
Zi Qiao Zheng
Keyword(s):  
Mechanical Properties ◽  
Aging Temperature ◽  
Solution Treatment ◽  
Heat Treatments ◽  
Alloying Elements ◽  
Solution Temperature ◽  
Lower Strength ◽  
Microstructures And Mechanical Properties ◽  
Zr Alloy

An Al-3.43Cu-1.28Li-0.49Mg-0.12Zr containing 0.62Zn and 0.29Mn was designed and the microstructures and mechanical properties of the alloy with various heat treatments were investigated. The precipitates of the alloy consist of T1 (Al2CuLi), θ′ (Al2Cu) σ (Al5Cu6Mg2) and δ′ (Al3Li). As solution temperature is changed from 485°C to 530°C, the solution degree of alloying elements in alloy increased, the amount of T1 in the alloy aged at 160°C for 18 h increased and that of θ′ is decreased, resulting in an increase of strength. After solution treatment at 530°C, the alloy aged for 18 h at 145°C is mainly strengthened by G P zones, and a little amount of T1 precipitates. As aging temperature is increased to 160°C and 175°C, the strength increased, due to the sufficient precipitation of σ and T1. The smaller amount of T1 in the alloy aged at 190°C is consistent with its lower strength. Meanwhile, it is found that the σ precipitate does not coarsen as aging temperature increases in the range from 160°C to 190°C.

scholarly journals Effects of solution and aging treatment parameters on the microstructure evolution of Ti–10V–2Fe–3Al alloy

2020 ◽  
Vol 39 (1) ◽  
pp. 501-509
Author(s):  
Wan-Liang Zhang ◽  
Wen-Tao Hao ◽  
Wei Xiong ◽  
Guo-Zheng Quan ◽  
Jiang Zhao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aging Temperature ◽  
Treatment Process ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Solution Temperature ◽  
Air Cooling ◽  
Water Cooling ◽  
Β Phase ◽  
Aging Conditions

AbstractThe solution-aging treatment parameters, including solution temperature, cooling rate and aging temperature, have significant influences on the microstructures and comprehensive mechanical properties of titanium alloy. In this work, the detailed microevolution behaviors of Ti–10V–2Fe–3Al alloy under different solution and aging conditions have been investigated through a series of heat-treatment experiments. The results of solution-treatment experiments reveal that the content of αp-phase is reduced to zero as the solution temperature is raised to a certain α → β critical transformation point. Recrystallized β-grains can be observed at the solution temperature of 820°C. In addition, the cooling way (air cooling or water cooling) has little influence on the microevolution behaviors for this alloy during the solution-treatment process. As for the solution-aging-treatment experiments, the results reveal that αs-phases are precipitated from the supersaturated β-phase, and the fraction of αs-phase increases with increasing aging temperature. However, the precipitated α-grains intend to coalesce and coarsen as the aging temperature raises above 510°C. Therefore, the advocated solution-aging-treatment program is solution treatment at 820°C with air cooling followed by aging treatment at 510°C with air cooling.

Sign in / Sign up

Export Citation Format

Share Document