Transition in high-temperature oxidation kinetics of Pd-modified aluminide coatings: Role of oxygen partial pressure, heating rate, and surface treatment

2000 ◽  
Vol 15 (3) ◽  
pp. 665-675 ◽  
Author(s):  
Daniel Monceau ◽  
Karima Bouhanek ◽  
Raphaëlle Peraldi ◽  
André Malie ◽  
Bernard Pieraggi
Keyword(s):  
Heating Rate ◽  
Photoelectron Spectroscopy ◽  
Secondary Ion Mass Spectrometry ◽  
Alumina Scale ◽  
Isothermal Oxidation ◽  
Temperature Oxidation ◽  
X Ray ◽  
Aluminide Coatings ◽  
Kinetic Transition ◽  
Direct Growth

The isothermal oxidation of Pd-modified Ni aluminide coatings was studied as a function of Po2 and temperature (900–1200 °C). A kinetic transition was observed between 900 and 1000 °C. Grazing incident x-ray diffraction, thermogravimetric analysis, x-ray photoelectron spectroscopy, scanning electron microscopy/energy dispersive spectroscopy, and secondary ion mass spectrometry analyses are consistent with the growth of δ-alumina or α-alumina below or above this transition temperature. Moreover, because Po2 was established before specimen heating, an effect of heating rate was observed and analyzed. More importantly, no kinetic transition was observed for sand-blasted specimens oxidized at low Po2. Thus conditions for the direct growth of an α-alumina scale could be determined from the reported results.

scholarly journals Microstructure and Isothermal Oxidation of Ir–Rh Spark Plug Electrodes

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3226
Author(s):  
Zhao ◽  
Xia ◽  
Xia ◽  
Chen ◽  
Du ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Isothermal Oxidation ◽  
Wire Drawing ◽  
Sem Analysis ◽  
Temperature Oxidation ◽  
X Ray ◽  
Spark Plug ◽  
Corrosion Pits ◽  
Resistance Performance

High-temperature oxidation tests were performed on pure iridium, rhodium, and the iridium alloys, IrRh10, IrRh25, and IrRh40, at 1100 °C in a stable air environment for 60 h. The results of the oxidation were analyzed by X-ray photoelectron spectroscopy (XPS). Microstructural changes of the Ir–Rh alloys were characterized by scanning electron microscopy (SEM). XPS analysis results show that the main oxide of the Ir–Rh alloy in a 1100 °C environment was Rh2O3, and SEM analysis shows that the surfaces of the Ir–Rh alloys after oxidation formed both linear and ellipse-shaped corrosion pits, and had the same direction with the wire-drawing process. The oxidation behavior of Ir–Rh alloys, including the mass change, the reason for the mass loss, and the role of Rh in improving oxidation resistance performance, are discussed.

Interaction of Bovine Serum Albumin and Lysozyme with Stainless Steel Studied by Time-of-Flight Secondary Ion Mass Spectrometry and X-ray Photoelectron Spectroscopy

Langmuir ◽  
2012 ◽  
Vol 28 (47) ◽  
pp. 16306-16317 ◽  
Author(s):  
Yolanda S. Hedberg ◽  
Manuela S. Killian ◽  
Eva Blomberg ◽  
Sannakaisa Virtanen ◽  
Patrik Schmuki ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Stainless Steel ◽  
Bovine Serum Albumin ◽  
Serum Albumin ◽  
Photoelectron Spectroscopy ◽  
Bovine Serum ◽  
Secondary Ion Mass Spectrometry ◽  
Time Of Flight ◽  
X Ray ◽  
Secondary Ion

Chromium implantation in silica glass

1996 ◽  
Vol 11 (1) ◽  
pp. 229-235 ◽  
Author(s):  
E. Cattaruzza ◽  
R. Bertoncello ◽  
F. Trivillin ◽  
P. Mazzoldi ◽  
G. Battaglin ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Photoelectron Spectroscopy ◽  
Silica Glass ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
Secondary Ion Mass Spectrometry ◽  
Rutherford Backscattering Spectrometry ◽  
X Ray ◽  
Chromium Silicide ◽  
Secondary Ion

Silica glass was implanted with chromium at the energy of 35 and 160 keV and at fluences varying from 1 × 1016 to 11 × 1016 ions cm−2. In a set of chromium-implanted samples significant amounts of carbon were detected. Samples were characterized by x-ray photoelectron spectroscopy, x-ray-excited Auger electron spectroscopy, secondary ion mass spectrometry, and Rutherford backscattering spectrometry. Chromium silicide and chromium oxide compounds were observed; the presence of carbon in the implanted layers induces the further formation of chromium carbide species. Thermodynamic considerations applied to the investigated systems supply indications in agreement with the experimental evidences.

Investigation of Contaminants in Single Wafer Wet Cleaning Using Isopropyl Alcohol

2021 ◽  
Vol 314 ◽  
pp. 23-28
Author(s):  
Seungjun Oh ◽  
Sunyoung Lee ◽  
Heehwan Kim ◽  
Donggeon Kwak ◽  
Chulwoo Bae ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Isopropyl Alcohol ◽  
Secondary Ion Mass Spectrometry ◽  
Oxidation Reactions ◽  
X Ray ◽  
Technological Control ◽  
Technological Developments ◽  
Ultra Trace ◽  
Ethylene Tetrafluoroethylene ◽  
Secondary Ion

Technological control over ultra-trace level contaminants is important for semiconductor development. Despite technological developments, defects remain in the single wafer wet cleaning process. In this paper, the source of the contamination is explained via trace analytical methods. Fluorine resin materials of polytetrafluoroethylene (PTFE) and ethylene tetrafluoroethylene (ETFE) are commonly used in semiconductor equipment. Isopropyl alcohol (IPA) oxidation reactions occur at high temperature below the boiling point due to impurities. IPA changed to different alcohol forms from gas chromatography (GCMS) analysis. The oxygen concentration in the X-ray photoelectron spectroscopy (XPS) results increased and formed new bonds in IPA with fluorine resin. These reactions confirmed that cations were a catalyst from the time-of-flight secondary ion mass spectrometry (TOF-SIMS) results. Representative ions were Fe+, K+, and Na+ with different concentrations for each material.

High Temperature Oxidation Behavior of SUS310S Austenitic Stainless Steel

2014 ◽  
Vol 941-944 ◽  
pp. 212-215
Author(s):  
Tao Zheng ◽  
Jing Tao Han
Keyword(s):  
Photoelectron Spectroscopy ◽  
Oxidation Behavior ◽  
Layer Structure ◽  
Energy Dispersive Spectrometer ◽  
Austenitic Stainless Steels ◽  
Temperature Oxidation ◽  
X Ray ◽  
High Temperature Oxidation Behavior ◽  
High Oxidation Resistance ◽  
Ray Diffusion

The oxidation behavior of SUS310S austenitic stainless steels was studied in isothermal conditions at different temperatures between 800oC and 1100oC for 96h in air. The oxidation kinetics was analyzed, the surface and cross-section of the oxide scale grown by oxidation were characterized by using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffusion (XRD) and X-ray photoelectron spectroscopy (XPS). The SUS310S steel has high oxidation resistance at 800oC and with the increase of the temperature, the parabolic rate constants is constantly increasing. Examination of the morphology and composition of oxide layers reveals a double-layer structure, The inner layer is mainly chromium oxide (Cr2O3) and is covered by an uneven thinness outer layer of manganese-chromium or iron-chromium spinel oxide.

Sign in / Sign up

Export Citation Format

Share Document