Fabrication of textured YBa2Cu3Ox superconductor using directional growth

1990 ◽  
Vol 5 (11) ◽  
pp. 2610-2612 ◽  
Author(s):  
Kwangsoo No ◽  
Dae-Shik Chung ◽  
Jae-Myung Kim
Keyword(s):  
Critical Current Density ◽  
Diffraction Analysis ◽  
Critical Current ◽  
Current Density ◽  
Growth Direction ◽  
X Ray Diffraction ◽  
Directional Growth ◽  
Powder Mixtures ◽  
X Ray ◽  
Microstructure Observation

Textured bulk YBa2Cu3Ox superconductor samples were fabricated using directional growth of superconductor grains reacted from Y2BaCuO5, BaCuO2, and CuO powder mixtures. The samples consisted of several mm long grains aligned parallel to the growth direction. The microstructure observation and x-ray diffraction analysis showed that the grains have a preferred orientation to improve critical current density.

Effect of Co0.5Ni0.5Fe2O4 Nanoparticles Addition in Ag-Sheathed Bi-2223 Superconductor Tapes Prepared by Co-Precipitation Method

2020 ◽  
Vol 981 ◽  
pp. 59-65
Author(s):  
Muhammad Hafiz Mazwir ◽  
Bryan Andrew Balasan ◽  
Farah Hanani Zulkifli ◽  
Roslan Abd-Shukor
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Magnetic Oxide ◽  
Pinning Centers ◽  
X Ray ◽  
Co Precipitation ◽  
Powder In Tube

Effect of complex magnetic oxide Co0.5Ni0.5Fe2O4 (CNFO) nanoparticles addition in (Bi1.6Pb0.4)Sr2Ca2Cu3O10 (Bi-2223) superconductor tapes was investigated. Ultrafine Bi-2223 powder precursor was prepared via co-precipitation method and was added with 0.01 – 0.05 wt.% Co0.5Ni0.5Fe2O4 nanoparticles during the final heating stage. The sample with 0.01 wt.% addition, Bi-2223(CNFO)0.01 was found to have the highest critical current density, Jc. This sample were then chosen to be fabricated into Ag-sheathed superconductor tapes using the powder-in-tube (PIT) method. The tapes were sintered for 50 and 100 h at 845 °C. The phase, microstructure and Jc of the samples were determined by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and four point probe, respectively. Jc of Ag-sheathed Bi-2223(CNFO)0.01 tapes sintered for 100 h was 19830 A/cm2 at 30 K and 3970 A/cm2 at 77 K compared to tapes without addition which showed a much lower Jc(6370 A/cm2 at 30 K). This study showed that CNFO nanoparticles could act as an effective flux pinning centers to enhance the critical current density in the Bi-2223 superconductor.

A SDUTY OF SUPERCONDUCTING OXIDE Y-Ba-Cu-Sn-O

1987 ◽  
Vol 01 (02) ◽  
pp. 277-280 ◽  
Author(s):  
Xin Jin ◽  
Huimin Shao ◽  
Guiqin Wang ◽  
Mu Lu ◽  
Hanhe Zhang ◽  
...  
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Magnetic Hysteresis ◽  
X Ray Diffraction ◽  
X Ray

A high-Tc superconductor YBa2Cu3 Snx07+z was characterized. We observed the existence about 90K superconductivity in variety of compositions. The samples were examined by x-ray diffraction , Mössbauer, SEM and EDS. Their structure are still ABO3 perovskite but part of Cu atoms are displaced by Sn. It was observed that when the x increased the critical current density were increased based on the measurements of magnetic hysteresis.

MAGNETIZATION AND INTRAGRANULAR CRITICAL CURRENT DENSITY IN Yb1Ba2Cu3O7−x HIGH TEMPERATURE SUPERCONDUCTOR

1995 ◽  
Vol 09 (28) ◽  
pp. 3715-3723
Author(s):  
RAANA MAHMOOD ◽  
M. NASIR KHAN ◽  
M. S. ZAFAR ◽  
FARID A. KHWAJA ◽  
A. WAHEED
Keyword(s):  
Electrical Resistivity ◽  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Applied Field ◽  
High Temperature Superconductor ◽  
Orthorhombic Structure ◽  
X Ray Diffraction ◽  
X Ray ◽  
Current Densities

The Yb 1 Ba 2 Cu 3 O 7−x samples have been prepared by the solid state reaction using the appropriate amount of Yb 2 O 3, BaCO 3, and CuO powders and characterized them using X-ray diffraction and electrical resistivity techniques. The X-ray diffraction pattern of the sample shows an orthorhombic structure refined in the space group Pmmm. The critical current densities are calculated from magnetization measurements over a temperature range 77 K to 86 K, and in magnetic fields up to 2 KOe. The intragrain critical current density is estimated to range from 5.24 × 106 ( A/cm 2) at an applied field of 0.2 KOe to 1.01 × 106 ( A/cm 2) at an applied field of 2 KOe at T = 77 K in this sample.

scholarly journals Highly c-axis orientated superconducting core and large critical current density in Ba0.6Na0.4Fe2As2 powder-in-tube tape

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
S. Imai ◽  
S. Itou ◽  
S. Ishida ◽  
Y. Tsuchiya ◽  
A. Iyo ◽  
...  
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
X Ray Diffraction ◽  
Axis Orientation ◽  
X Ray ◽  
Superconducting Wires ◽  
Superconducting Tape ◽  
Key Issues ◽  
Powder In Tube

Abstract Improvement of the critical current density (Jc) of superconducting wires/tapes is one of the key issues in the field of superconductivity applications. Here we report the fabrication of a silver-sheathed Ba1−xNaxFe2As2 (BaNa-122) superconducting tape by using a powder-in-tube technique and its superconducting properties, in particular transport Jc, as well as the tape-core texture. The optimally-doped BaNa-122 tape with Na concentration x = 0.4 exhibits the superconducting critical temperature (Tc) of 33.7 K and high transport Jc of 4 × 104 A/cm2 at 4.2 K in a magnetic field of 4 T. Patterns of x-ray diffraction for the superconducting core show that the degree of c-axis orientation is significantly enhanced through the tape fabrication process. The tendency of c-axis orientation is advantageous for achieving higher Jc, suggesting the high potential of BaNa-122 for superconducting wire/tape applications.

Effects of Nano-Sized BN Doping on the Phase Formation, Tc and Critical Current Density of MgB2 Superconductor

2005 ◽  
Vol 23 ◽  
pp. 113-116 ◽  
Author(s):  
S. Soltanian ◽  
M. Delfany ◽  
X.L. Wang ◽  
M.J. Qin ◽  
H.K. Liu ◽  
...  
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Magnetic Measurements ◽  
Magnetic Measurement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Measurement Results ◽  
Diffraction Patterns ◽  
Synthesized Materials

MgB2 polycrystalline bulk samples with additions of 0, 5, 10 and 20% wt.% nano-sized BN powders were prepared using the reaction in-situ method. All the samples were sintered at 850°C for 1h in Ar. All the samples were characterized by X-ray diffraction, scanning electron microscopy (SEM) and magnetic measurements. The X-ray diffraction patterns show that the BN does not react with Mg and B during the heat treatment and remains as a separate phase. The synthesized materials thus contain two separate BN and MgB2 phases. In addition, the samples contain a small, almost constant amount of MgO. SEM shows that the samples contain MgB2 grains with average grain sizes of about 250 nm. Magnetic measurement results show that the critical current density and irreversibility fields decrease slightly as the BN level increases. The Tc drops slightly from 38.9 to 38.2 K and has a sharp transition with a transition width of less than 1 K. The field dependence of Jc for all the samples is also presented.

Impact of Eu Nanoparticles Substitution for Ca Site in Bi(Pb)-2223 Cuprates Superconductor

2020 ◽  
Vol 301 ◽  
pp. 202-208
Author(s):  
E.S. Nurbaisyatul ◽  
H. Azhan ◽  
Kasim Azman ◽  
Norazila Ibrahim ◽  
Siti Fatimah Saipuddin
Keyword(s):  
Critical Temperature ◽  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Solid State Reaction Method ◽  
Nominal Composition ◽  
Superconducting Properties ◽  
X Ray Diffraction ◽  
Effective Surface ◽  
X Ray

The sample with nominal composition of Bi1.6Pb0.4Sr2Ca2-xEuxCu3Oy where x = 0.000, 0.0025, 0.020, 0.050 and 0.100 were synthesized through solid state reaction method. The effect of Eu2O3 nanoparticles doping on the superconducting and structural properties were studied by means of critical temperature, TC, critical current density, JC, X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The amount of 2223 phase gradually decreased with the increment of Eu concentration which indicates that Eu nanoparticles substitution at Ca site favours the growth of 2212 phases. The sample with higher porosity was found to be decreased in critical temperature, TC as well as critical current density, JC due to the lack of effective surface area for current flowing. The best superconducting properties were observed at x = 0.0025 substitutes into Ca site for Bi (Pb)-2223 host sample.

Crystalline Alignment and In-plane Texture Improvement of Buffer Layers Deposited on NiW Tapes

2011 ◽  
Vol 1308 ◽  
Author(s):  
Linfei Liu ◽  
Yijie Li ◽  
Huaran Liu ◽  
Xiaokun Song ◽  
Dan Hong ◽  
...  
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Buffer Layers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Deposition Parameters ◽  
Current Densities ◽  
Diffraction Peaks ◽  
Deposition Conditions

ABSTRACTIn order to deposit YBCO coated conductor with high critical current densities on rolling assisted biaxially textured Ni-W tapes, this paper has systematically studied the influence of deposition conditions on the orientation, in-plane texture and surface morphology of buffers and superconducting layers. It was found that the crystalline alignment and the in-plane texture of cerium oxide cap-layers were well improved by optimizing deposition parameters. The full width at half maximum of phi-scan x-ray diffraction peaks were reduced from original values of 7-8 degrees to 5-6 degrees. A high critical current density of 4.6×106 A/cm2 has been achieved on optimized buffer layers. This value is comparable with the critical current density of YBCO thin films deposited on single crystalline substrates.

scholarly journals Transport Critical Current Density of (Bi1.6Pb0.4)Sr2Ca2Cu3O10Ceramic Superconductor with Different Nanosized Co3O4Addition

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Nur Jannah Azman ◽  
Huda Abdullah ◽  
Roslan Abd-Shukor
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Diffraction Method ◽  
Solid State Reaction Method ◽  
Small Addition ◽  
Transport Critical Current Density ◽  
X Ray Diffraction ◽  
Conventional Solid State Reaction ◽  
X Ray

The effect of different nanosized Co3O4(10, 30, and 50 nm) addition on the Bi1.6Pb0.4Sr2Ca2Cu3O10(Co3O4)xsuperconductor withx=0–0.05 wt.% has been investigated using X-ray diffraction method, scanning electron microscopy, transition temperature, and critical current densityJcmeasurements. The samples were prepared by the conventional solid-state reaction method. Samples withx=0.01 wt.% Co3O4(10 nm) showed the highestTc-zeroat 102 K. The highestJcwas observed in thex=0.03 wt.% Co3O4(10 nm) andx=0.02 wt.% Co3O4(30 nm) samples. At 77 K,Jcof the 10 nm and 30 nm Co3O4added samples was 6 and 13 times larger than the nonadded samples, respectively. Small addition of Co3O4nanoparticles in the Bi1.6Pb0.4Sr2Ca2Cu3O10(Bi-2223) samples enhanced the critical current density and the phase formation. The larger Co3O4nanoparticle (50 nm) had a greater degradation affect on superconductivity of the Bi-2223 phase.

Effect of ZnO Nano-Oxide Addition on the Superconducting Properties of the (Bi.Pb)2223 Phase

2011 ◽  
Vol 324 ◽  
pp. 241-244 ◽  
Author(s):  
R. Mawassi ◽  
R. Awad ◽  
Mohamad Roumie ◽  
M. Kork ◽  
I. Hassan
Keyword(s):  
Critical Current Density ◽  
Critical Current ◽  
Current Density ◽  
Flux Pinning ◽  
High Temperature Superconductors ◽  
Weak Links ◽  
Superconducting Properties ◽  
X Ray ◽  
Weight Percentage ◽  
Nano Oxide

The major limitation of Bi-system superconductor applications is the intergrain weak links and weak flux pinning capability producing low critical current density of the Bibased phases. In order to enhance these characteristics and other superconducting properties, effective flux pinning centers are introduced into high temperature superconductors. In this work, different weight percentages of ZnO nano oxide were introduced at the final stage of the Bi1.8Pb0.4Sr2Ca2Cu3O10-y superconductor preparation process. Phase characterization was completed by X-ray diffraction (XRD). Exact constitution of the samples was determined using particle induced X-ray emission (PIXE). Granular and microstructure were investigated using scanning electron microscopy (SEM). Electrical resistivity as function of the temperature was carried to evaluate the relative performance of samples, and finally, E-J characteristic curves were obtained at 77K. Using 0.4 ZnO weight percentage, the electrical and granular properties were greatly enhanced, indicating more efficient pinning mechanisms. A critical current density of 949 A/cm2 was obtained which represents more than twice the value obtained for the pure sample (Jc= 445 A/cm2).

Influence of Time and Temperature on Directional Growth of MoO3

2016 ◽  
Vol 869 ◽  
pp. 1001-1006
Author(s):  
Claudia Ferreira da Silva ◽  
André Lima e Silva ◽  
Francisco Xavier Nobre ◽  
Edson Cavalcanti Silva Filho ◽  
Luiz de Sousa Santos Jr. ◽  
...  
Keyword(s):  
Glacial Acetic Acid ◽  
Molybdenum Trioxide ◽  
Orthorhombic Phase ◽  
Growth Direction ◽  
X Ray Diffraction ◽  
Directional Growth ◽  
Preferential Growth ◽  
X Ray ◽  
Preferential Growth Direction ◽  
Characteristic Modes

Two-dimensional microstructures of molybdenum trioxide (MoO3) were synthesized by heptamolybdate tetrahydrate ammonium acidification, followed by calcination. A solution of the precursor compound heptamolybdate tetrahydrate ammonium acidified to pH 3,5 using glacial acetic acid followed by hydrothermal treatment for 150, 180 and 200 °C for 1, 6 and 12 hours. Then, the intermediate was calcined at 300 °C for varying time 6 and 12h to obtain MoO3. X-ray diffraction revealed that the crystals grew with crystalline structure corresponding to the orthorhombic phase of MoO3 (a-MoO3) as major phase, with a preferential growth direction along the planes (0K0). Raman spectroscopy and IR confirmed the formation of the characteristic modes of molybdenum trioxide for stage found. With Scanning Electron Microscopy (SEM) was possible to observe the formation of nanoplates.

Sign in / Sign up

Export Citation Format

Share Document