scholarly journals INVESTIGATION OF IMPEDANCE-DIFFERENTIAL PROTECTION’S ALGORITHM AS A FAULT LOCATOR FOR DOUBLE-CIRCUIT TRANSMISSION LINE

2020 ◽  
Vol 2020 (6) ◽  
pp. 57-60
Author(s):  
J. Herlender ◽  
◽  
J. Izykowski ◽  
B. Brusilowicz ◽  
◽  
...  
Keyword(s):  
Transmission Line ◽  
Fault Location ◽  
Differential Protection ◽  
Location Accuracy ◽  
Negative Sequence ◽  
Additional Relation ◽  
Zero Sequence ◽  
Impedance Parameters

This paper deals with an analysis of impedance-differential protection algorithm applied to locate faults on a double-circuit transmission line. In particular, the study of fault location accuracy for the case of using the relation between currents for negative-sequence not for zero-sequence, as it was presented so far, is provided. It results from the well-known fact that zero-sequence impedances are in practice considered as quite unreliable data. Therefore, one has to limit usage of zero-sequence impedance parameters as much as possible. Such approach was applied in this paper and therefore the use of the additional relation of currents for negative-sequence is under investigation. The fault signals from ATP-EMTP simulation on the sample double-circuit transmission line was applied for evaluating the fault location accuracy. References 8, figures 4, table 1.

Fault Location Scheme for Transmission Lines Using Kaiser Self-Convolution Windowed FFT Phase Comparison

2014 ◽  
Vol 596 ◽  
pp. 659-663
Author(s):  
Guo Chen Fan ◽  
Yong Li Zhu ◽  
Hong Wei Yan ◽  
Yan Feng Gao
Keyword(s):  
Transmission Line ◽  
Transmission Lines ◽  
Fault Location ◽  
Power Transmission ◽  
Phase Spectrum ◽  
Power Transmission Line ◽  
Excellent Performance ◽  
Location Accuracy ◽  
Spectral Leakage ◽  
Convolution Window

In order to improve the fault location accuracy, and eliminate the influence of spectral leakage in power transmission line fault location, we proposed a novel fault location scheme for transmission lines based on multi-measurements and phase comparison with Kaiser self-convolution windows FFT, which can locate the fault between two adjacent towers in the fault-prone segment. It is based Kaiser self-convolution window's excellent performance of leakage suppression, which can effectively solve the phase current fault component is relatively large errors due to spectral leakage problem. Firstly, this paper analyzes the causes of the phase spectrum leakage, then elaborates the sidelobe characteristics of Kaiser self-convolution window, and lists phase comparative fault location using steps, finally, verifies the correctness of the proposed method by simulation. The results show that the proposed method can effectively suppress spectral leakage, has a high location accuracy, a wide applicability and its solving of phase difference is precise.

scholarly journals Earth Fault Location Using Negative Sequence Currents

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3759 ◽  
Author(s):  
Farughian ◽  
Kumpulainen ◽  
Kauhaniemi
Keyword(s):  
Fault Location ◽  
Single Phase ◽  
Distribution Networks ◽  
Practical Implementation ◽  
Negative Sequence ◽  
Medium Voltage ◽  
Different Types ◽  
Sequence Components ◽  
Zero Sequence ◽  
Negative Sequence Current

In this paper, a new method for locating single-phase earth faults on non-effectively earthed medium voltage distribution networks is proposed. The method requires only current measurements and is based on the analysis of the negative sequence components of the currents measured at secondary substations along medium voltage (MV) distribution feeders. The theory behind the proposed method is discussed in depth. The proposed method is examined by simulations, which are carried out for different types of networks. The results validate the effectiveness of the method in locating single-phase earth faults. In addition, some aspects of practical implementation are discussed. A brief comparative analysis is conducted between the behaviors of negative and zero sequence currents along a faulty feeder. The results reveal a considerably higher stability level of the negative sequence current over that of the zero sequence current.

scholarly journals Combined DFT and Fuzzy Based Faulty Phase Selection and Classification in a Series Compensated Transmission Line

2019 ◽  
Vol 2019 ◽  
pp. 1-18 ◽  
Author(s):  
Praveen Kumar Mishra ◽  
Anamika Yadav
Keyword(s):  
Transmission Line ◽  
Fault Location ◽  
Fault Classification ◽  
Testing Time ◽  
Heavy Load ◽  
Phase Selection ◽  
Protection Scheme ◽  
Fault Resistance ◽  
Zero Sequence ◽  
Series Capacitor

The conventional distance protection scheme malfunctions sometimes in case of a fixed series capacitor compensated transmission line due to the change in relaying impedance of the protected line during faulty conditions. In order to mitigate this problem, a combined discrete Fourier transform and fuzzy (CDFTF) based algorithm has been proposed in this paper. This method has been tested on a 400 km, 735 kV series compensated transmission line network and WSCC 3-machine 9-bus system for all fault types using MATLAB/Simulink and PSCAD platforms, respectively. A fixed series capacitor is located at the middle of the protected line. The fundamental components of phase currents, phase voltages, and zero-sequence current are fed as inputs to the proposed scheme. The fault detection, faulty phase selection, and fault classification are achieved within 1/2–1 cycle of power frequency. The proposed CDFTF-based scheme is less complex and is better than other data mining techniques which require huge training and testing time. Test results corroborate the proposed scheme reliability with wide variations in fault location, fault resistance, fault inception angle, evolving faults, compensation level, and heavy load interconnection. The results discussed in this work indicate that the proposed technique is resilient to wide variations in fault and system conditions.

scholarly journals Design of Traveling Wave Location Method for Transmission Line Fault Based on EMD-TEO

2020 ◽  
Vol 2 (3) ◽  
pp. 73
Author(s):  
Juan Xia
Keyword(s):  
Transmission Line ◽  
Instantaneous Frequency ◽  
Traveling Wave ◽  
Fault Location ◽  
Arrival Time ◽  
Location Accuracy ◽  
Location Method ◽  
Hilbert Huang Transform ◽  
Mode Decomposition ◽  
Positioning Method

<p>With the rapid development of the social economy and the continuous extension of Internet technology, China’s power grid has entered the ranks of large-scale, high-voltage, and intelligent. The main purpose of the fault location of the transmission line is to eliminate hidden trouble and restore the fault line in time to ensure the safe and stable operation of the power system. With the advent of the smart grid, higher requirements are put forward for fault location accuracy, while the traditional wavelet transform and Hilbert-Huang transform have larger defects.</p><p>Therefore, this paper extensively analyses the generation and characteristics of fault traveling waves in transmission line fault, which proves that the traveling wave location method has higher location accuracy than the fault analysis method. Among them, the two-terminal traveling wave positioning method only uses the arrival time of the initial traveling wave, avoiding the principled defects and locating the dead zone of the single-terminal traveling wave positioning method, so the two-terminal traveling wave positioning method is generally used. The key of the two-terminal traveling wave location method is that it can accurately detect the arrival time of the initial traveling wave head. Although the Hilbert-Huang Transform (HHT) method can be used to detect the arrival time of the initial traveling wave head, the problem of inaccurate detection or failure of the wave head may arise when the instantaneous frequency of the IMF component decomposed by the Hilbert-Huang transform is used because of the mode aliasing in the empirical mode decomposition algorithm. Based on the above analysis, an empirical mode decomposition (EMD) combined with the Teager energy operator(TEO) is proposed for the traveling wave fault location of transmission lines. A large number of simulations prove that the EMD-TEO method in this paper can solve the problem of inaccuracy or failure of the HHT method using instantaneous frequency to detect the arrival time of wave head, and has higher fault location accuracy.</p>

Sign in / Sign up

Export Citation Format

Share Document