scholarly journals Structure, Mechanical Properties And Weldability Of Pseudo-alpha and (alpha + beta)-Ti Alloys Strengthened By Silicides

2016 ◽  
Vol 2016 (2) ◽  
pp. 51-56 ◽  
Author(s):  
G.M. Grigorenko ◽  
◽  
O.M. Zadorozhnyuk ◽  
Keyword(s):  
Mechanical Properties ◽  
Ti Alloys ◽  
Alpha Beta

scholarly journals Novel α + β Zr Alloys with Enhanced Strength

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 418
Author(s):  
Anna Veverková ◽  
Dalibor Preisler ◽  
Mariia Zimina ◽  
Tereza Košutová ◽  
Petr Harcuba ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Section ◽  
Absorption Cross Section ◽  
Neutron Absorption ◽  
Absorption Cross ◽  
Ti Alloys ◽  
Alpha Beta ◽  
Nuclear Applications ◽  
Neutron Absorption Cross Section ◽  
Zr Alloys

Low-alloyed zirconium alloys are widely used in nuclear applications due to their low neutron absorption cross-section. These alloys, however, suffer from limited strength. Well-established guidelines for the development of Ti alloys were applied to design new two-phase ternary Zr alloys with improved mechanical properties. Zr-4Sn-4Nb and Zr-8Sn-4Nb alloys have been manufactured by vacuum arc melting, thermo-mechanically processed by annealing, forging, and aging to various microstructural conditions and thoroughly characterized. Detailed Scanning electron microscopy (SEM) analysis showed that the microstructural response of the alloys is rather similar to alpha + beta Ti alloys. Duplex microstructure containing primary alpha phase particles surrounded by lamellar alpha + beta microstructure can be achieved by thermal processing. Mechanical properties strongly depend on the previous treatment. Ultimate tensile strength exceeding 700 MPa was achieved exceeding the strength of commercial Zr alloys for nuclear applications by more than 50%. Such an improvement in strength more than compensates for the increased neutron absorption cross-section. This study aims to exploit the potential of alpha + beta Zr alloys for nuclear applications.

Phase Transformations in Ti-7w/oMo-3w/oMe Alloy

1974 ◽  
Vol 32 ◽  
pp. 514-515
Author(s):  
S. Fujishiro
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Mechanical Processing ◽  
Ray Method ◽  
X Ray ◽  
Transmission Electron ◽  
Water Quench ◽  
Alpha Beta

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.

scholarly journals First principles computation of composition dependent elastic constants of omega in titanium alloys: implications on mechanical behavior

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
R. Salloom ◽  
S. A. Mantri ◽  
R. Banerjee ◽  
S. G. Srinivasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
First Principles ◽  
Young's Modulus ◽  
Group Vi ◽  
Group V ◽  
Β Phase ◽  
Ti Alloys ◽  
Ω Phase ◽  
Stabilizer Concentration

AbstractFor decades the poor mechanical properties of Ti alloys were attributed to the intrinsic brittleness of the hexagonal ω-phase that has fewer than 5-independent slip systems. We contradict this conventional wisdom by coupling first-principles and cluster expansion calculations with experiments. We show that the elastic properties of the ω-phase can be systematically varied as a function of its composition to enhance both the ductility and strength of the Ti-alloy. Studies with five prototypical β-stabilizer solutes (Nb, Ta, V, Mo, and W) show that increasing β-stabilizer concentration destabilizes the ω-phase, in agreement with experiments. The Young’s modulus of ω-phase also decreased at larger concentration of β-stabilizers. Within the region of ω-phase stability, addition of Nb, Ta, and V (Group-V elements) decreased Young’s modulus more steeply compared to Mo and W (Group-VI elements) additions. The higher values of Young’s modulus of Ti–W and Ti–Mo binaries is related to the stronger stabilization of ω-phase due to the higher number of valence electrons. Density of states (DOS) calculations also revealed a stronger covalent bonding in the ω-phase compared to a metallic bonding in β-phase, and indicate that alloying is a promising route to enhance the ω-phase’s ductility. Overall, the mechanical properties of ω-phase predicted by our calculations agree well with the available experiments. Importantly, our study reveals that ω precipitates are not intrinsically embrittling and detrimental, and that we can create Ti-alloys with both good ductility and strength by tailoring ω precipitates' composition instead of completely eliminating them.

Fabrication of Titanium / Biodegradable-Polymer FGM for Medical Application

2009 ◽  
Vol 631-632 ◽  
pp. 199-204 ◽  
Author(s):  
Yoshimi Watanabe ◽  
Yoshimi Iwasa ◽  
Hisashi Sato ◽  
Akira Teramoto ◽  
Koji Abe
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Medical Application ◽  
Hot Water ◽  
Porous Ti ◽  
Ti Alloys ◽  
Plasma Sintering ◽  
Biodegradable Poly ◽  
Spark Plasma

Ti and Ti alloys are widely used as metallic implants, because of their good mechanical properties and nontoxic behavior. However, they have problems as the implant-materials, namely, high Young’s modulus comparing that of bone and low bonding ability with bone. There is a need to develop the Ti and Ti alloys with lower Young’s modulus and good bonding ability. In previous study, Ti composite containing biodegradable poly-L-lactic-acid (PLLA) fiber has been fabricated to improve these problems. However, this composite has low strength because of the imperfect sintering of Ti matrix. To improve its strength, sintering of Ti matrix should be completed. In this study, Ti-NaCl composite material was fabricated by spark plasma sintering (SPS) method using powder mixture of Ti and NaCl to complete the sintering of Ti matrix. To obtain porous Ti samples, Ti-NaCl composite were put into hot water of 100 oC. The porous Ti was dipped into PLLA melt in order to introduce PLLA into the pores of porous Ti. Finally, Ti-PLLA composite was obtained, and PLLA plays a role as reinforcement of Ti matrix. It was found that the Ti-PLLA composite has gradient structure and mechanical properties.

Effects of Cooling Rate and Sn Addition on the Microstructure of Ti-Nb-Sn Alloys

2011 ◽  
Vol 172-174 ◽  
pp. 190-195 ◽  
Author(s):  
Giorgia T. Aleixo ◽  
Eder S.N. Lopes ◽  
Rodrigo Contieri ◽  
Alessandra Cremasco ◽  
Conrado Ramos Moreira Afonso ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Melting Furnace ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Β Phase ◽  
Arc Melting ◽  
Ti Alloys ◽  
Ω Phase

Ti-based alloys present unique properties and hence, are employed in several industrial segments. Among Ti alloys, β type alloys form one of the most versatile classes of materials in relation to processing, microstructure and mechanical properties. It is well known that heat treatment of Ti alloys plays an important role in determining their microstructure and mechanical behavior. The aim of this work is to analyze microstructure and phases formed during cooling of β Ti-Nb-Sn alloy through different cooling rates. Initially, samples of Ti-Nb-Sn system were prepared through arc melting furnace. After, they were subjected to continuous cooling experiments to evaluate conditions for obtaining metastable phases. Microstructure analysis, differential scanning calorimetry and X-ray diffraction were performed in order to evaluate phase transformations. Depending on the cooling rate and composition, α” martensite, ω phase and β phase were obtained. Elastic modulus has been found to decrease as the amount of Sn was increased.

An assessment into mechanical properties and microstructural behavior of TIG welded Ti-6Al-4V titanium alloy

2020 ◽  
Vol 10 (3) ◽  
pp. 281-292 ◽  
Author(s):  
Saurabh Dewangan ◽  
Suraj Kumar Mohapatra ◽  
Abhishek Sharma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
High Strength ◽  
Hardness Test ◽  
Content Type ◽  
Ti Alloys ◽  
Microstructure And Mechanical Properties ◽  
Grade 5 ◽  
Selection Of

PurposeTitanium (Ti) alloys are in high demand in manufacturing industries all over the world. The property like high strength to weight ratio makes Ti alloys highly recommended for aerospace industries. Ti alloys possess good weldability, and therefore, they were extensively investigated with regard to strength and metallurgical properties of welded joint. This study aims to deal with the analysis of strength and microstructural changes in Ti-6Al-4V (Grade 5) alloy after tungsten inert gas (TIG) welding.Design/methodology/approachTwo pair of Ti alloy plates were welded in two different voltages, i.e. 24 and 28 V, with keeping the current constant, i.e. 80 A It was a random selection of current and voltage values to check the performance of welded material. Both the welded plates were undergone through some mechanical property analysis like impact test, tensile test and hardness test. In addition, the microstructure of the welded joints was also analyzed.FindingsIt was found that hardness and tensile properties gets improved with an increment in voltage, but this effect was reverse for impact toughness. A good corroboration between microstructure and mechanical properties, such as tensile strength, hardness and toughness, was reported in this work. Heat distribution in both the welded plates was simulated through ANSYS software to check the temperature contour in the plates.Originality/valueA good corroboration between microstructure and mechanical properties, such as tensile strength, hardness and toughness, was reported in this study.

Sign in / Sign up

Export Citation Format

Share Document